Floe MAXIS Bedienungsanleitung

Andere Floe Bootsausrüstung Handbücher

Floe

Floe 510-27300-00 Kurzanleitung

Floe

Floe VSD 3800 Bedienungsanleitung

Floe

Floe V1600 PWC Bedienungsanleitung

Floe

Floe V1600 PWC Bedienungsanleitung

Floe

Floe 510-17700-00 Bedienungsanleitung

Floe

Floe PONTOON CRADLE PADS Bedienungsanleitung

Floe

Floe 510-27200-00 Kurzanleitung

Floe

Floe V2602 LENGTH BUNKS Bedienungsanleitung

Floe

Floe VSD Leitfaden

Floe

Floe VSD6500 Bedienungsanleitung

Floe

Floe INSTA-FLOAT Produkthandbuch

Floe

Floe 510-20000-00 Bedienungsanleitung

Floe

Floe VSD 6000 Bedienungsanleitung

Floe

Floe VSD 6000 Bedienungsanleitung

Floe

Floe 510-27100-00 Kurzanleitung

Floe

Floe 510-27400-00 Kurzanleitung

Floe

Floe X-SHALLOW 510-17100-00 Kurzanleitung

Floe

Floe VSD 6000 Bedienungsanleitung

Floe

Floe 510-89304-00 Bedienungsanleitung

Floe

Floe VSD 8000 Bedienungsanleitung

Floe

Floe SHOREWAY QUICK PIVOT Bedienungsanleitung

Floe

Floe 510-27500-00 Kurzanleitung

Floe

Floe VSD 5000 Bedienungsanleitung

Floe

Floe VSD 6-8000 Bedienungsanleitung

Beliebte Bootsausrüstung Handbücher anderer Marken

Ideal Windlass

Ideal Windlass CWM Leitfaden

Access

Access BIMINI Bedienungsanleitung

Faun

Faun C40 Trackway Bedienungsanleitung

Exalto

Exalto 240BS Bedienungsanleitung

Hobie

Hobie Mirage 360 Bedienungsanleitung

Dowco

Dowco V322 CC - 2019 Bedienungsanleitung

Humphree

Humphree HCS-5 Bedienungsanleitung

Vetus

Vetus BOW4512D Technisches Datenblatt

Dock Doctors

Dock Doctors SLIDING BOARDING STEP Bedienungsanleitung

Mastervolt

Mastervolt Mass Combi 12/2000-100 Original Betriebsanleitung

Zattini Group

Zattini Group bamar BOXTRON E14S Benutzerhandbuch

SeaView

SeaView PM5-FMD-8 Bedienungsanleitung

Vetus

Vetus HTANK Bedienungsanleitung

Grammer

Grammer AVENTO MSG 65/511 Betriebsanleitung

Furuno

Furuno TZTL12F Bedienungsanleitung

Harken

Harken 944 Bedienungsanleitung

ShoreLand'r

ShoreLand'r DUB 2314 Bedienungsanleitung

ProFurl

ProFurl C480 Bedienungsanleitung

SHEET 1 OF 8

FLOE MAXIS EXTENSION KIT 6-10K

ASSEMBLY INSTRUCTIONS

KIT P/N 512-65030-00

TOOLS REQUIRED

-9/16” SOCKET/WRENCH

-3/4” SOCKET/WRENCH

-TORQUE WRENCH

-TAPE MEASURE

INSTRUCTION P/N: 611

-

6

5030

-

00

RELEASED 06/12/19

© Manufactured by:

Floe International Inc.

48473 State Hwy. 65

McGregor, MN 55362

www.floeintl.com

*LIFT

AND CANOPY

N

OT INCLUDED

SHEET 2 OF 8

BILL OF MATERIALS/EXPLODED VIEW

P/N 512-65030-00

KIT, MAXIS EXTENSION 6-10K

NUMBER PART NUMBER QTY. DESCRIPTION

1 001-70207-00 2 HHCS, ½-13 x 1 ¼” 18-8 ss

2 001-71021-00 2 FLAT WASHER, ½” 18-8 SS

3 001-76072-00 2 NUT, NYLOCK ½-13 ALUM.

4 002-00257-00 2 TUBE, MAXIS LEG EXTENSION 6-10K – 12”

5 002-00258-00 2 INSERT, CANOPY 6-10K W/ PIVOT HOLE – 44”

6 112-01075-00 2 ASS’Y, CANOPY INSERT W/ GUIDE HOLES – 44”

SHEET 3 OF 8

STEP 1

IF INSTALLED, REMOVE VINYL CAP FROM TOP OF EACH CORNER POST. USE A ½” X 1-1/4” BOLT

AND ½” WASHER FROM CANOPY HOOP HARDWARE (FIGURE 1.1). PLACE THE BOLT AND WASHER

INTO THE CORNER POST (FIGURE 1.2). SLIDE AN INSERT INTO EACH OF THE CORNER POSTS, THEN

START A ½” NYLOCK NUT (INCLUDED WITH CANOPY HOOP HARDWARE) ON THE BOLT, BUT DO

NOT TORQUE. CORNER POSTS ON THE TILTING SIDE USE INSERT P/N 002-00258-00 (ONE

THROUGH HOLE) (FIGURE 1.3). CORNER POSTS ON THE NON-TILTING SIDE USE THE INSERT P/N

112-01075-00 (TWO THROUGH HOLES) (FIGURE 1.4).

FIGURE 1.1

FIGURE 1.2

FIGURE 1.3

FIGURE 1.4

SHEET 4 OF 8

THE MAXIMUM HEIGHT OF THE INSERTS IS 38” (6” OF ENGAGEMENT IN THE CORNER POSTS). THE

MINIMUM HEIGHT OF THE INSERTS IS 26” (18” OF ENGAGEMENT IN THE CORNER POSTS) (FIGURE

1.5). TORQUE ½” NUT TO 60 FT-LBS (FIGURE 1.6). PROCEED TO INSTALL MAXIS CANOPY BY

REFERRING TO MAXIS CANOPY FRAME INSTRUCTIONS.

FIGURE 1.5

SHEET 5 OF 8

STEP 2 (IF INSTALLING MAXIS TILTING CANOPY)

INSTALL (1) ½” X 1 1/4” BOLT AND (1) ½” WASHER INTO EXTENSION TUBE. NOTE THAT THE

EXTENSION TUBE IS SLID OVER THE INSERTS ON THE NON-TILTING SIDE. DEPENDING ON THE

CONFIGURATION, IT IS EITHER ON THE MOTOR SIDE (CORNER POSTS “B” & “C”) OR THE LIFTING

SIDE (CORNER POSTS “A” & “D”). FOR EITHER CONFIGURATION, IT IS ALWAYS THE INSERT WITH

TWO THROUGH HOLES (112-01075-00) (FIGURE 2.1). START (1) ½” NYLOCK NUT ON THE ½” BOLT,

BUT DO NOT TORQUE. THEN, SLIDE EXTENSION ONTO INSERT (FIGURE 2.2).

FIGURE 2.1

FIGURE 2.2

SHEET 6 OF 8

FIRST, SET HEIGHT OF EXTENSION TUBE 7-3/8” FROM TOP OF CORNER POST. THEN, SWING LOWER

ACTUATOR MOUNT AND ACTUATOR TOWARDS EXTENSION TUBE (FIGURE 2.3). EXTENSION TUBE

WILL BE APPROXIMATELY 5-3/16” FROM TOP OF TUBE TO TOP OF ACTUATOR MOUNT. TORQUE 60

FT-LBS (FIGURE 2.4).

FIGURE 2.3

FIGURE 2.4

SHEET 7 OF 8

NOTE (MAXIS TILT KIT INSTALLATIONS)

SHEET 8 OF 8