FlowLine EchoPod UG06 Series Bedienungsanleitung

Flowline, Inc. | 10500 Humbolt Street, Los Alamitos, CA 90720 p 562.598.3015 f 562.431.8507 w flowline.com QS310140 Rev A2

Made in USA

UG06 & UG12 Series Quick Start

EchoPod®

Ultrasonic Liquid Level Transmitter

| 2 QS310140 Rev A2

WELCOME TO THE ECHOPOD® QUICK START

The EchoPod® Quick Start provides basic mounting, setup and use instructions for getting the EchoPod®

up and running quickly. If you have a non-standard installation or setup requirement that is not

addressed here, please refer to the EchoPod® Manual or other support documentation located at

flowline.com.

WE DO YOUR LEVEL BEST

Thank you for purchasing EchoPod®. The sensor provides integrated LCD and three push-button

configuration. This quick start includes everything you’ll need to get the sensor up and running.

COMPONENTS

Depending on how the sensor part number that was shipped, EchoPod® comes with a Viton® gasket for

installation and the Quick Start.

EchoPod®

UG06-0001-00

UG06-0001-01

UG06-0011-00

UG06-0011-01

EchoPod®

UG12-0001-00

UG12-0001-01

UG12-0011-00

UG12-0011-01

USB® Key Fob

P/N: LI99-2001

Viton® gasket (2”)

P/N: 200129

G threaded version only

Viton® gasket (3”)

P/N: 210157

G threaded version only

ENCLOSURE

While the switch housing is liquid-resistant the EchoPod® is not designed to be operational when immersed. It

should be mounted in such a way that the enclosure and transducer do not come into contact with the

application media under normal operational conditions. Before closing the enclosure, make sure that the

enclosure gasket is properly seated, and that any conduit fittings, cable connectors or plugs are installed

correctly and sealed. Note: If using the Flowline LM90-1001 (liquid tight fitting) on the ½” conduit, the cable

minimum is 0.170” (4.3mm) and the maximum is 0.450” (11.4mm).

CONFIGURATION

When configuring EchoPod®, choose either the WebCal® or Push Button method. Either method will

accomplish the goal of sensor configuration. Changes to the configuration can be made using the alternative

method. When beginning with one method, it is recommended to complete the configuration before using the

other method to make any adjustments.

Note: When connecting the sensor to the WebCal®Software, you must remove the display or the software will

not connect. Once completed, you can re-connect the display to the terminal.

QS31

Ech

perf

STE

spe

Win

You

inst

STE

Not

not

The

the

140 Rev

FIGURING

Pod

is co

rmed prior

1: INSTAL

nload Web

ifications:

ows

2000

must have

ll software

2: CONNE

:Do not c

:When co

onnect. O

sensor com

port, ens

omputer a

1. Rem

from

2. Con

Ech

termi

3. Tigh

scre

4. Plug

CHOPOD

(

figured thr

to mounting

WEBCAL

al® softwa

XP/Vista/7/

n active In

efore proc

T THE US

nnect the

necting the

ce complet

municates t

re that all e

d EchoPod

ve the dis

the connec

ect the pro

Pod

to the

nals on the

. Power (+

)

. Power (-)

. WebCal (

en the term

driver.

the Fob int

EBCAL)

ugh WebC

, since it re

SOFTWAR

e from ww

/10, 10 M

ernet conn

eding to St

FOB

ob to your

sensor to t

d, you can

WebCal

ternal pow

is 15’.

lay and un

or on the ci

er terminal

correspond

Fob.

)

to Red

to Black

W) to Whit

G) to Gree

nal screws

your PC’s

, a PC so

uires conn

.flowline.co

storage sp

ction to do

p 2. Install

omputer u

e WebCal

re-connect

hrough the

r is discon

lug the cabl

cuit board.

from the

ing colored

ith a slotte

port.

tware progr

ction to yo

m/webcal-s

ce, 256 M

nload Web

er program

til after you

Software,

he display

USB

Fob.

ected from

d Wirin

Black,

am. Config

r PC.

ftware ont

RAM, 1 U

. Doubl

ill automa

’ve installed

ou must re

o the termi

Prior to plu

EchoPod

identical f

Green and

ration of y

a PC with

2.0 port

e-click the

ically install

WebCal

ove the dis

al.

ging the Fo

The maxim

r all serie

White wir

ur sensor s

he followin

ebCal

ins

any require

ftware.

lay or the

into your

m distanc

– Use onl

hould be

minimum

taller to

drivers.

oftware will

omputers

between

the Red,

3 |

| 4 QS310140 Rev A2

STEP 3 - MEASURE THE TANK

Measuring the tank is one of the most important aspects

in configuring the sensor. When measuring the tank,

take into account the location of the sensor with respect

to fittings, risers, dome tops and bottoms, and identify

where the measurements are taken from the sensor.

The HEIGHT and FILL-H settings determine the 4-

20mA span and are always measured from the bottom

of the tank up.

STEP 4 - SENSOR CONFIGURATION

Configures the Loop Fail-Safe, Output at Empty and Startup Condition for the sensor.

QS310140 Rev A2 5 |

STEP 5 – DIMENSIONAL ENTRY

Distance Mode (default): Output of sensor is based on the distance (height of liquid) in the tank. Any change

in liquid level will reflect linearly to the current output. The two values (Sensor Height and Fill-Height) below set

the 4-20 mA current span for the sensor. Both values will be set in the units shown under Height Units.

Height Units: Confirm units for use in Sensor Height and Fill-Height settings.

Sensor Height: Sets the location for 4mA. It is based on the distance from the Empty level position

(bottom of tank) to the Measurement location for the sensor (bottom of sensor).

Fill-Height: Sets the location for 20mA. It is based on the distance from the Empty level position

(bottom of tank) to the Full level position (see below).

STEP 6 - TANK LEVEL CONFIRMATION

Verify the Height Units, Sensor Height & Fill-Height. All values were calculated and set in the previous

Dimensional Entry window. Make any adjustments if required.

| 6 QS310140 Rev A2

STEP 7 - WRITE TO UNIT

This WebCal®* operation uploads the configuration into the sensor, provides a custom wiring diagram specific

to the signal output and/or relay configuration, and saves the configuration file to your hard drive.

* For complete information on the WebCal® software, please refer to the WebCal® manual located at

flowline.com/webcal-software.

Before configuration can be completed:

 You must click the Write to Unit button to save the settings to the unit.

 Then, click Wiring Diagram for a hard copy of the sensor’s settings.

 Finally, enter the file name under which you wish to save the configuration file and click Save Config

File.

Configuration is now complete.

Disconnect the USB® Fob before continuing to the next step: Mounting the EchoPod®.

QS310140 Rev A2 7 |

CONFIGURING ECHOPOD® (DISPLAY)

TOP-LEVEL MENU

The sensor is configured with the three buttons on the sensor face (UP, DOWN and OK) and the sensor’s

LCD. To access the sensor’s Top-level menu, simply hold down the OK button for five seconds. The display

menu will automatically begin to scroll through the TOP-LEVEL MENU.

When the menu scrolls to an item you wish to configure, simply press the OK button to choose that item. The

TOP-LEVEL MENU will continue to scroll through the following (UNITS – TANK – dISPLY – OUTPUT –

VALUES – RUN), If you miss your selection, it will appear again shortly.

 To return to the TOP-LEVEL MENU, press OK when EXIT appears.

 To return to Operational Mode of the sensor, press OK when RUN appears in the TOP-LEVEL MENU.

 Note: To speed up the scrolling of the values on the display, hold down the OK button while holding

down the UP or DOWN buttons.

STEP 1 - MEASURE THE TANK

Measuring the tank is one of the most important aspects in

configuring the sensor. When measuring the tank, take into

account the location of the sensor with respect to fittings, risers,

dome tops and bottoms, and identify where the measurements

are taken from the sensor. The HEIGHT and FILL-H settings

determine the 4-20mA span and are always measured from the

bottom of the tank up.

Height: Sets the location for 4mA. It is based on the distance

from the Empty level position (bottom of tank) to the

Measurement location for the sensor (bottom of sensor).

Fill-Height: Sets the location for 20mA. It is based on the

distance from the Empty level position (bottom of tank) to the

Full level position (see below).

#2 - SETTING THE UNITS OF MEASUREMENT (UNITS)

The EchoPod

displays information in the following units:

inches, feet, centimeters, meters or percentage. The value

shown on the display represents the amount of liquid in the

tank.

1) In TOP-LEVEL MENU mode, select UNITS.

2) Next, select INCHES, FEET, CM or METERS by holding

down OK button.

3) Finally, select EXIT to return to the TOP-LEVEL MENU.

| 8 QS310140 Rev A2

#3 - SETTING THE HEIGHT (SENSOR HEIGHT) & #4 - SETTING THE FILL-H (FILL-HEIGHT)

This setting customizes the reading for your installation.

Follow these instructions to set the height and fill height for your tank:

1) In TOP-LEVEL MENU mode, select TANK.

2) Select HEIGHT.

3) Use the UP and DOWN buttons, set the

HEIGHT of your tank.

4) To enter the value, press and hold OK for 3

seconds and release. SAVED will display.

HEIGHT is now set.

5) Select FILL-H.

6) Use the UP and DOWN buttons, set the

HEIGHT of your tank.

7) To enter the value, press and hold OK for 3

seconds and release. SAVED will display.

FILL-H is now set.

8) Select EXIT to return to the TOP-LEVEL MENU.

9) Select RUN to return to Operational Mode.

Note: The Height and Fill Height settings also determine the 4 to 20 mA current span.

The Height setting determines the 4mA position and the Fill-H setting determines the 20 mA position.

#5 - HOW TO SELECT FAIL-SAFE CURRENT OUTPUT (LOST)

In the event the sensor does not receive an echo,

the Fail-Safe Current Output or LOST setting can

be set to output a current of 4mA, 20mA, 21mA,

22mA or HOLD (last known value). During fail-

safe, the display will read LOST.

1) In TOP-LEVEL MENU mode, select SAFE.

2) Select 4mA, 20mA, 21mA, 22mA or

HOLD by holding down OK button.

3) Select EXIT to return to the TOP-LEVEL

MENU.

TROUBLESHOOTING

If you face any issues not addressed in this Quick Start, please refer to the EchoPod® Manual located on

Flowline’s website at www.flowline.com.

QS310140 Rev A2 9 |

MOUNTING ECHOPOD®

The sensor should always be mounted perpendicular to the liquid surface. Insure that there are no restrictions

or obstacles in the path of the acoustic signal. For further mounting information, please refer to the EchoPod®

manual at www.flowline.com.

Installation in existing 3” fittings:

Use a LM52-2400 3” thread x 2” thread adapter or a LM52-2410 3”

slip x 3” thread adapter (UG06 series only).

Basic Tank Installation:

Use a 2” bulkhead fitting, such as the LM52-2890 bulkhead fitting

for the UG06 series or a 3” bulkhead fitting, such as the LM52-

3890 for the UG12 series.

Use a larger bulkhead fitting, such as the LM52-3890 with a

reducer bushing such as the LM52-2400.

Use a flange with a 2” thread, such as the LM52-2850.

Weld a plastic 2” half coupling to the tank top.

Mounting in Riser:

Installations with tall, narrow risers can impede the acoustic signal.

2" diameter risers should be no taller than 5". Larger diameter

risers should be no taller than 12". For best results, follow a 2:1

Height to Inner Diameter ratio (example: 8” High to 4” Inner

Diameter).

Installation in open tanks and sumps:

Use Flowline's LM50-1001 side mount bracket.

Note: The Side Mount Bracket (LM50 series) is not designed

for use with stand pipes or as a method to secure stand pipes.

There are too few threads to properly hold the sensor and the

stand pipe.

LM50-1001

LM52-2400

LM52-2890

LM52-2850

Mounting in Riser

| 10 QS310140 Rev A2

IMPORTANT MOUNTING GUIDELINES

1) Never mount the sensor at an angle.

2) Liquid should never enter the dead band.

3) Mount at least 3” from the side wall.

4) Never mount the sensor in a vacuum.

5) Do not obstruct the sensor’s beam width with objects underneath the sensor.

6) Do not mount in the center of a dome top tank.

7) In a cone bottom tank, position the sensor over the deepest part of the tank.

8) Avoid mounting in a riser where the sensor is recessed more than twice the diameter of the riser.

MOUNTING IN A STAND-PIPE

A stand-pipe may be used to dampen turbulence, separate surface foam from the point of measurement or

increase performance in heavy vapor. When mounting the sensor in a stand-pipe, the minimum diameter of the

pipe is 3”, minimum 4” for the UG12 series. Larger diameter pipes can be used. The pipe should be attached

with a coupling or tank adapter and reducer bushing. Avoid the use of multiple pipe fittings when possible. An

ideal mount would be to select a 3” tank adapter (S x T or S x S) and connect the pipe to the inside slip and use

a reducer bushing to attach the sensor (see example below).

The pipe length should run the measurement span and the bottom of the pipe should remain submerged at all

times to prevent foam from entering the pipe. Cut the bottom end of the pipe at 45° and drill a 1/4” pressure

equalization hole within the sensor’s dead band. Locate the stand-pipe away from pump outlets and/or other

sources of substantial turbulence which might cause the liquid in the pipe to oscillate.

3” x 2”

Reducer Bushing

(TxT)

3” Tank

Adapter

(S x T)

3” PVC Pipe

Stand-Pipe Example

Stand-Pipe Mounting

Andere Handbücher für EchoPod UG06 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere FlowLine Sender Handbücher

FlowLine

FlowLine EchoBeam LR80 Series Bedienungsanleitung

FlowLine

FlowLine EchoTouch US03 Series Bedienungsanleitung

FlowLine

FlowLine EchoSpan LU80-5101 Bedienungsanleitung

FlowLine

FlowLine EchoPulse LR15 Series Bedienungsanleitung

FlowLine

FlowLine EchoSonic II LU23 Series Bedienungsanleitung

FlowLine

FlowLine EchoBeam LR83 Series Bedienungsanleitung

FlowLine

FlowLine EchoSonic LU23-00 Bedienungsanleitung

FlowLine

FlowLine EchoPod UG03 Series Bedienungsanleitung

FlowLine

FlowLine EchoPro LR11 Series Bedienungsanleitung

FlowLine

FlowLine EchoPulse LR10 Series Bedienungsanleitung

FlowLine

FlowLine LU20 Bedienungsanleitung

FlowLine

FlowLine EchoTouch US01 Series Bedienungsanleitung

FlowLine

FlowLine EchoSpan LU80 series Bedienungsanleitung

FlowLine

FlowLine EchoWave LG11 Series Bedienungsanleitung

FlowLine

FlowLine EchoSafe XP88 Bedienungsanleitung

FlowLine

FlowLine EchoPod US01-03 Bedienungsanleitung

FlowLine

FlowLine EchoSpan LU80 series Bedienungsanleitung

FlowLine

FlowLine DeltaSpan LD30 Series Bedienungsanleitung

FlowLine

FlowLine EchoPod UG12 Series Bedienungsanleitung

FlowLine

FlowLine EchoSonic II Bedienungsanleitung

FlowLine

FlowLine EchoTouch US12 Series Bedienungsanleitung

FlowLine

FlowLine EchoPulse LR30 Series Bedienungsanleitung

FlowLine

FlowLine LA12 Bedienungsanleitung

FlowLine

FlowLine EchoSafe XP88 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung