Fluke 80i-110s Bedienungsanleitung
Table of Contents 3
November 1996
¤1994, 1996 Fluke Corporation.
All rights reserved. All product names are
trademarks of their respective companies.
Printed in the Netherlands
80i-110s
AC/DC CURRENT PROBE
Users Manual
®
Table of Contents 1
Table of Contents
INTRODUCING THE CURRENT PROBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLING THE BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
USING THE CURRENT PROBE SAFELY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SAFETY SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
BATTERY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INSTRUMENT COMPATIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
USING THE CURRENT PROBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MEASUREMENT CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CLEANING AND STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PERFORMANCE VERIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
80i-110s Instruction Manual 3
INTRODUCING THE CURRENT PROBE
The Fluke 80i-110s is a clamp-on AC/DC Current Probe that reproduces current
waveforms found in modern commercial and industrial power distribution sys-
tems. The probe's performance is optimized for accurate reproduction of currents
at line frequency and up to the 50th harmonic waveform. The 80i-110s is also
compatible with any instrument capable of millivolt measurements. The Current
Probe (shown in Figure 1) provides the following benefits:
• Accurate AC, DC and AC+DC current measurements for Electrical, Electronic
and Automotive applications.
• Shielded for high noise immunity around electronic motor drives and ignition
systems.
• Wide measurement range from 50 milliamps to 100 amps, useful to 10
milliamps.
• Jaw shaped for easy access to cramped spaces.
• Safety-designed 600 volt insuIated BNC - compatible with Fluke ScopeMeter£
test tools, Power Harmonic analyzers, and oscilloscopes.
•Selectable output of 10 millivolts per 1 amp for the 100 A range, and 100
millivolts per 1 amp for the 10 A range.
Figure 1. 80i-110s AC/DC Current Probe
4 80i-110s Instruction Manual
UNPACKING
The following items should be included in your Current Probe box:
•AC/DC Current Probe, 80i-110s
•Users Manual (this book)
•Quick Reference Card
•9 volt Battery, type IEC 6LR61
Check the contents of the shipping box for completeness. If something in the box
has been damaged or missing, contact your distributor or the nearest FLUKE
sales or service office immediately.
80i-110s Instruction Manual 5
INSTALLING THE BATTERY
WARNING
TO AVOID ELECTRICAL SHOCK, UNCLAMP THE CURRENT PROBE FROM
ANY CONDUCTOR, AND DISCONNECT THE SCOPEMETER TEST TOOL OR
ANY OTHER MEASUREMENT DEVICE BEFORE INSTALLING OR REPLACING
THE BATTERY.
Atfirstuse,remembertoinstallthebattery.ReferringtoFigure2,usethefollowing
procedure to install the battery:
1. Be sure that you have unclamped the Current Probe from any conductor and
have disconnected the ScopeMeter test tool or any other measurement device.
2. Be sure that the Current Probe is in the OFF position.
3. Locate the battery cover on the handle. (see Figure 2.) Loosen the screw with
a flat-blade screwdriver.
4. Slide the battery cover away from the Current Probe.
5. Install the battery (IEC 6LR61) as shown in Figure 2. Arrange the battery leads
sothattheywillnotbepinchedbetweenthehandlebottomandthebatterycover.
6. Reinstall the battery cover and secure the screw.
Figure 2. Installing the Battery
6 80i-110s Instruction Manual
USING THE CURRENT PROBE SAFELY
ATTENTION
Carefully read the following safety information before attempting to operate
or service the Current Probe.
•Never use the probe on circuits rated higher than 600V in Installation
Category II (CAT II) or 300V in Installation Category III (CAT III). (See
"Safety Specifications".) Use extreme caution when clamping around
uninsulated conductors or bus bars.
•Keep your fingers off the probe jaws.
•Check the magnetic mating surfaces of the probe jaws; these should be free
of dust, dirt, rust, and other foreign matter.
•Do not use a probe that is cracked, damaged, or has a defective cable. Such
probes should be made inoperative by taping the clamp shut to prevent
operation.
In this Users Manual, a WARNING identifies conditions and actions that pose haz-
ard(s) to the user. A Caution identifies conditions and actions that may damage
the current probe. International electrical symbols used are explained below.
The80i-110sisdesignedtomeet the requirements ofIECPublication 1010 and oth-
er safety standards (see "Safety Specifications"). Follow all warnings to ensure safe
operation.
Use of this equipment in a manner not specified herein may impair the protection
provided by the equipment.
DC - Direct Current Caution
(see explanation in manual)
AC - Alternating Current Equipment protected throughout
by DOUBLE INSULATION or
REINFORCED INSULATION
Earth Recycling
ConformitéEuropéenne
80i-110s Instruction Manual 7
ELECTRICAL SPECIFICATIONS
All Electrical Specifications are valid at a temperature of 23 qC r3 qC (73 qFr5 qF).
Current Ranges:
0 to 10A dc or ac peak
0 to 100A dc or ac peak
Output Signals:
10A range: 100 mV/A
100A range: 10 mV/A
Working voltage (Clamps jaws to Ground):
600V ac rms on Installation Category II per IEC 1010-1 circuits.
300V ac rms on Installation Category III per IEC 1010-1 circuits.
Floating Voltage (Output cable and connector to Ground):
600V ac rms on Installation Category II per IEC 1010-1 circuits.
300V ac rms on Installation Category III per IEC 1010-1 circuits.
Basic Accuracy (DC to 1kHz):
Extended Accuracy:
For other frequencies, refer to the appropriate input current range and add the
error listed below to the "Basic Accuracy" error.
Input Current
(DC or AC peak) Error (after zero check)
100 mV/A 10 mV/A
0 to 10A
0 to 40A
40 to 80A
80 to 100A
<3% of reading +50 mA
-
-
-
-
<4% of reading +50 mA
<12% of reading +50 mA
<15% of reading
Frequency Additional Error
100 mV/A 10 mV/A
1 to 5 kHz
5 to 20 kHz
>20 kHz
3%
12%
not specified
3%
12%
not specified
8 80i-110s Instruction Manual
Input Load Impedance (of host instrument):
>1 M:in parallel with up to 100 pF.
Useful Bandwidth (-3 dB):
0 to 100 kHz
Rise or Fall Time:
<4 Psec.
Output noise level:
10 mV/A typ. 480 PV pk-pk
100 mV/A typ. 3 mV pk-pk
Max. non destructive current:
0 to 2 kHz 140A peak
2 to 10 kHz 110A peak
10 to 20 kHz 70 A peak
20 to 50 kHz 30A peak
50 to 100 kHz 20A peak
Temperature coefficient:
2000 ppm/qC max. for temperature from 0 to 50 qC (32 to 132 qF)
Andere Handbücher für 80i-110s
1
Inhaltsverzeichnis
Andere Fluke Messgerät Handbücher
Fluke
Fluke 983 Bedienungsanleitung
Fluke
Fluke 805 FC Bedienungsanleitung
Fluke
Fluke OptiView T1/E1 Bedienungsanleitung
Fluke
Fluke 433 Konfigurationshandbuch
Fluke
Fluke 377 Bedienungsanleitung
Fluke
Fluke ScopeMeter 199B Bedienungsanleitung
Fluke
Fluke 374 FC Gebrauchs- und Pflegehandbuch
Fluke
Fluke 85RF II Bedienungsanleitung
Fluke
Fluke 43B Bedienungsanleitung
Fluke
Fluke CertiFiber Pro Bedienungsanleitung
Fluke
Fluke 353 Bedienungsanleitung
Fluke
Fluke i310s Bedienungsanleitung
Fluke
Fluke CO-220 Bedienungsanleitung
Fluke
Fluke 6050H Bedienungsanleitung
Fluke
Fluke 374 FC Bedienungsanleitung
Fluke
Fluke 434-II Konfigurationshandbuch
Fluke
Fluke ScopeMeter 190 II 190-104 Bedienungsanleitung
Fluke
Fluke 922 Bedienungsanleitung
Fluke
Fluke 374 Bedienungsanleitung
Fluke
Fluke Victoreen 190 Bedienungsanleitung
