Fluke 830 Bedienungsanleitung
830
July 2020 PN DOC 24.103.EN
© 2020 Fluke Corporation. All rights reserved. All rights reserved. Specications are subject to change
without notice. All product names are trademarks of their respective companies.
Laser Alignment Tool
Users Manual Addendum
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
830
Users Manual
2
Changes
Introduction . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 4
2. Package ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 4
3. Safety and operating notes ... ... ... ... ... ... ... ... ... ... ... ... ... 6
4. FLUKE 830 - an overview (Change 1) ... ... ... ... ... ... ... ... ... 7
4. FLUKE 830 - an overview (Change 2) ... ... ... ... ... ... ... ... ... 8
6. Getting started (Change 1) . ... ... ... ... ... ... ... ... ... ... ... ... . 14
6. Getting started (Change 2) . ... ... ... ... ... ... ... ... ... ... ... ... . 15
7. Horizontal machine alignment (Change 1) ... ... ... ... ... ... . 16
7. Horizontal machine alignment (Change 2) ... ... ... ... ... ... . 17
7. Horizontal machine alignment (Change 3) ... ... ... ... ... ... . 17
7. Horizontal machine alignment (Change 4) ... ... ... ... ... ... . 20
7. Horizontal machine alignment (Change 5) ... ... ... ... ... ... . 23
10. Appendix ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 25
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
830
Users Manual
4
Introduction
This addendum explains the functions of the sensor with integrated wireless
data transmission technology (the Wireless Sensor or the Sensor). Use this
addendum with the Users Manual for the Fluke 830 Laser Alignment Tool (the
Product). See each section for changes.
On page 28, make sure the setting for Wireless is ON.
2. Package
On pages 5 and 6, replace the Package chapter with:
2. Package
Table 2-1. Package items is a list of all the items included with the Product. The
items are shown in Figure 2-1. Items included with the Product.
Table 2-1. Package items
Item Description Part Number
Fluke 830 Laser Alignment Tool 4503893
Storage case 4462624
Wireless Sensor including dust cap 5237155
Prism including dust cap 5144366
Chain-type bracket (2 no.) – each comprises two support
posts and chain 4503916
Adapter/charger for power to Alignment Tool 4503957
USB Adapter/charger for power to sensor 5168024
Micro USB cable for power to sensor 5153070
PC cable 4503925
USB cable for USB memory stick 4503933
USB memory stick 4473175
Cleaning cloth 2687537
N/A Quick reference guide 4473130
N/A Safety sheets 4473148
N/A 830 Users manual N/A
N/A 830 Users manual addendum (this document) DOC 24.103.EN
1
2
3
4
5
6
7
8
9
10
11
12
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
5
Addendum
BACK
CLEAR ENTER
1
4
7
-
+
GHI
PQRS
2
5
8
0
ABC
JKL
TUV
space
3
6
9
DEF
MNO
WXYZ
./*
1 2
3
4
8
7
9
10
6
11
12
5
AU EU
CN
US
UK
Figure 2-1. Items included with the Product
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
830
Users Manual
6
3. Safety and operating notes
On page 7, replace the IP classication section and the rst paragraph in the
Laser safety section, with:
IP classication
Both the Product and the Wireless Sensor comply with code IP65 (dustproof and
water jets resistant). The prism complies with code IP67 (dust-tight and protected
against immersion).
Laser safety
This Product uses a Class 2 laser according to the requirements of IEC 60825-
1:2014. This laser complies with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007. The laser
operates at a wavelength of 630 nm – 680 nm and has a maximum radiant power
<1 mW. No maintenance is necessary to keep the product compliant as outlined
above.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
7
Addendum
4. FLUKE 830 - an overview (Change 1)
On page 17, in the Mounting and dismounting the universal adapter/charger plug
section, replace text and Figure 4-3 as follows:
Mounting and dismounting the universal adapter/charger plug
The universal adapter/charger comes with regional plugs for the Euro zone, the
US/Canada/Japan, the UK, Australia and China.
To mount the plug:
1. Push down the latch and hold [A].
2. Insert the plug into the housing with the lip on the leading edge [B].
When the latch is pushed down, the arrow inside the charger housing shows
the direction to insert the plug. The plug is locked into position when the latch
release springs back into position.
To dismount a plug, push down the latch [A]. The plug pops out.
1
2
Figure 4-3. Mounting the charger plug
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
830
Users Manual
8
4. FLUKE 830 - an overview (Change 2)
On pages 18-19, replace the Sensor section with:
Wireless Sensor
The Wireless Sensor mounts using the chain type bracket on the shaft or solid
coupling of the left machine (usually stationary machine) – as viewed from the
normal working position.
The Sensor contains a position detector, which measures the position of the laser
beam as the shafts are rotated. The Sensor also contains an electronic inclinom-
eter for shaft rotation measurements. The semiconductor laser diode within the
Sensor emits a ray of red light (wavelength 630 nm to 680 nm) which is visible at
the point it strikes a surface. The Class 2 laser beam is emitted with a diameter of
approximately 5 mm (3/16”).
The Sensor has two indicator LEDs on the front. See Figure 4-4. Parts of the
Sensor. When facing the sensor, the left LED [A] indicates the laser beam
adjustment and the charging status. The LED on the right [B] indicates the
wireless communication status and lights blue when scanning and when commu-
nication is established. See Table 4-2. Monitoring sensor LEDs.
The internal optics and electronics are internally sealed to prevent possible con-
tamination. The Sensor lens, however, must be kept clean. Use the lens cleaning
cloth or a ne dusting brush such as that normally used to clean other optical
devices. Keep the dust cap on when not in use.
An internal rechargeable battery powers the Sensor.
To turn on the Sensor, press the On/O switch on the Sensor. The red LED lights
when sensor is switched on.
To turn o the Sensor, press and hold the On/O switch until both LEDs are o.
Warning
When the Wireless Sensor is on, the laser beam is emitted. DO NOT stare
into the laser beam.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
9
Addendum
Figure 4-4. Parts of the Sensor
Caution
Avoid polishing the lens too vigorously to prevent irreparable damage to
its anti-reective coating.
Caution
DO NOT remove the six housing torx head screws. Removing the screws
voids the warranty.
Note
Check the calibration accuracy of the Wireless Sensor every two years as in-
dicated by the colored label located on the back of the housing. Return the
Sensor to your authorized service center for calibration.
Warning
Do not stare into the beam.
A Laser beam status and charging LED; B Laser on/Communication LED;
C Laser beam; D Scratch resistant lens; E Sensor dust cap; FHousing;
G Locking knob; H Micro USB port; I On/O switch
1 8 9
2
3
4
6
7
5
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
830
Users Manual
10
Wireless Sensor LEDs
Table 4-2. Monitoring sensor LEDs
Activity Status / Charging LED (left)
(See [A] in Figure 4-4)
Laser On / Communication LED (right)
(See [B] in Figure 4-4)
Turn on Lights red for 1 second, then red or green
(depending on the battery capacity) for
another second, then blinks red
Lights blue for 1 second then blinks red (indi-
cating laser emission)
Laser beam
status
Blinks red when laser is OFF
Blinks orange when laser is in END position
Blinks green when laser is centered or in
‘laser OK’ position
When wireless communication is established,
blinks blue once then red three times (indicat-
ing laser emission). This sequence repeats.
Charging Blinks fast green during fast charge (0 % -
90 %)
Blinks slowly green when charge is > 90 %
Steady green when charge is 100 %
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
11
Addendum
Charging the Wireless Sensor
Use the mains supply or a PC to charge the Sensor.
Note
Charging the Sensor using the mains supply is faster than when charging
through a PC.
Use the supplied micro USB to connect the charging source to the Sensor. (See
Figure 4-8. Charging the non-removable rechargeable battery.)
Figure 4-8. Charging the non-removable rechargeable battery
USB
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Andere Handbücher für 830
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Fluke Messgerät Handbücher
Fluke
Fluke DSX-600 CableAnalyzer Bedienungsanleitung
Fluke
Fluke 1520 Bedienungsanleitung
Fluke
Fluke 700GA4 Bedienungsanleitung
Fluke
Fluke 772 Gebrauchs- und Pflegehandbuch
Fluke
Fluke 5790B Bedienungsanleitung
Fluke
Fluke MultiFiber Pro Bedienungsanleitung
Fluke
Fluke 333 Technisches Handbuch
Fluke
Fluke 80PK-26 Bedienungsanleitung
Fluke
Fluke 732C Konfigurationshandbuch
Fluke
Fluke 321 Technisches Handbuch
Fluke
Fluke 1742 Konfigurationshandbuch
Fluke
Fluke 700G04 Bedienungsanleitung
Fluke
Fluke 323 PLUS Bedienungsanleitung
Fluke
Fluke 15B MAX Bedienungsanleitung
Fluke
Fluke 430 Series Gebrauchsanweisung
Fluke
Fluke 165X Bedienungsanleitung
Fluke
Fluke TS44DLX Bedienungsanleitung
Fluke
Fluke 789 Gebrauchs- und Pflegehandbuch
Fluke
Fluke CableAnalyzer DSX-5000 Bedienungsanleitung
Fluke
Fluke i3000s Flex Series Bedienungsanleitung
