Fluke I100 Bedienungsanleitung

i100

AC/DC Solar Current Clamp

100 A

Instructions

Introduction

Fluke current clamps extend the current ranges of Fluke tools.

The Fluke i100AC/DC Solar Current Clamp is highly reliable,

measures 1 Ato100 A and provides accurate current reading

without breaking the circuit. This clamp measures both ac and dc

current with a large jaw, battery-powered Hall-effect probe that

gives access to difficult toreach areas.

Safety

A Warning identifies hazardous conditions and procedures that

are dangerous to the user. A Caution identifies conditions and

procedures that can cause damage to the Product or the

equipment under test.

XW Warning

To prevent possible electrical shock, fire, or personal

injury:

Carefully read all instructions.

Read all safety information before you use the

Product.

PN 5292418 (English) August 2022

subject to change without notice. All Product names are trademarks of

their respective companies.

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

Do not alter the Product and use only as specified, or

the protection supplied by the Product can be

compromised.

Do not use the Product around explosive gas, vapor,

or in damp or wet environments.

Do not touch voltages >30 V ac rms, 42 V ac peak, or

60 V dc.

Do not use the Product if it operates incorrectly.

Do not use the Product if it is altered or damaged.

Comply with local and national safety codes. Use

personal protective equipment (approved rubber

gloves, face protection, and flame-resistant clothes)

to prevent shock and arc blast injury where hazardous

live conductors are exposed.

Before each use, examine the Product. Look for cracks

or missing pieces of the clamp housing or output cable

insulation. Also look for loose or weakened

components. Carefully examine the insulation around

the jaws.

Use the Clamp only on insulated conductors. Use

caution around bare conductors or bus bars. To

prevent electrical shock, do not touch the conductor.

Do not apply more than the rated voltage and rated

current on the jaws.

Do not use a current measurement as an indication

that a circuit is safe to touch. A voltage measurement

is necessary to know if a circuit is hazardous.

Hold the Product behind the tactile barrier.

Remove the input signals before you clean the

Product.

Repair the Product before use if the battery leaks.

Battery leakage may create a shock hazard or damage

the Product.

Batteries contain hazardous chemicals that can cause

burns or explode. If exposure to chemicals occurs,

clean with water and get medical aid.

Remove the batteries if the Product is not used for an

extended period of time, or if stored in temperatures

above 50 °C. If the batteries are not removed, battery

leakage may result.

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

The battery door must be closed and locked before

you operate the Product.

Be sure that the battery polarity is correct to prevent

battery leakage.

Use only specified replacement parts.

Have an approved technician repair the Product.

Symbols

The table below lists the symbols that can be used on the Product

or in this document.

Instructions

To use the Clamp:

1. Connect the green plug to the green socket on the Analyzer.

2. Connect the yellow plug to the yellow socket on the Analyzer.

3. Select FUNC./PAC/DC on the Analyzer.

4. Turn on the Clamp .

The ON indicator turns on.

Symbol Description

»Consult user documentation.

WWARNING. RISK OF DANGER.

XWARNING. HAZARDOUS VOLTAGE. Risk of electric

shock.

Do not apply current sensor to or remove from

HAZARDOUS LIVE UNINSULATED CONDUCTORS,

which may render electric shock, electric burn, or

arc flash.

MBattery

PConforms to European Union directives.

This product complies with the WEEE Directive and

its marking requirements. The affixed label indicates

that you must not discard this electrical/electronic

product in domestic household waste. Do not

dispose ofthis product as unsorted municipal

waste. For information about take-back and

recycling programs available in your country, see

the website.

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

5. Rotate the Zero Adjust knob (jaws empty) until 0.0 shows on

the Analyzer display.

6. Open the Clamp jaw  and place around the insulated

conductor.

The measurement shows on the Analyzer display.

Item Description

ON/OFF Button

Jaw Lever

Jaw

Zero Adjust

ON Indicator

i100

AC/DC SOLAR

CURRENT CLAMP

OUTPUT:10mV/A

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

Maintenance

Clean with a soft towel moistened with water and mild detergent.

DO NOT IMMERSE in liquid.

Battery Replacement

For specified battery life, replace with alkaline batteries.

Product Disposal

Dispose of the Product in a professional and environmentally

appropriate manner. Remove batteries that are not integrated into

the electrical system before disposal and dispose of batteries

separately.

Specifications

Maximum voltage between any Terminal

and Earth Ground ......................1000 V

Operating Temperature............0 °C to 50 °C (14 °F to 122 °F)

Storage Temperature...............-30 °C to 60 °C (-22 °F to 140 °F)

Relative Humidity ......................<80 % RH, up to 40 °C (104 °F)

<40 % RH, up to 50 °C (122 °F)

Operating Altitude.....................2000 m

Storage Altitude.........................12 000 m

Battery Type (x2)........................1.5 V AA (alkaline) IEC LR6

Battery Life ..................................50 hr typical

Output Signal..............................10 mV/A dc or ac

Jaw Opening...............................34 mm

Cable Length ..............................150 cm

Load Impedance........................≥1 MΩ, ≤100 pF

Specified Current Range ........1 A to 100 A dc / 1 A to 100 A ac rms

Note

With a true-rms voltmeter, the minimum ac current is

limited to the low end of the specified mV ac range.

Usable Current Range .............0.2 A to 100 A

DC Accuracy (zero adjusted,

conductor centered) ................1.5 % + 0.1 A

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

AC Accuracy ...............................1.5 % + 0.1 A

up to 1 kHz

Crest Factor ≤3

Temperature Coefficient.........±(0.1 x accuracy) per °C

(0 °C to 18 °C, 28 °C to 50 °C)

Size.................................................246 x 83 x 45 mm

Weight...........................................0.39 kg

Safety ............................................IEC 61010-1, Pollution Degree 2

IEC 61010-2-032, Type D current

sensor (for use on insulated

conductors), 1000 V max

Electromagnetic Compatibility (EMC)

International. .........................IEC 61326-1: Portable,

Electromagnetic Environment,

IEC 61326-2-2 CISPR 11: Group 1,

Class A

Group 1: Equipment has intentionally generated and/or uses

conductively-coupled radio frequency energy that is

necessary for the internal function of the equipment itself.

Class A: Equipment is suitable for use in all establishments

other than domestic and those directly connected to a low

voltage power supply network that supplies buildings used for

domestic purposes. There may be potential difficulties in

ensuring electromagnetic compatibility in other environments

due to conducted and radiated disturbances.

Caution: This equipment is not intended for use in residential

environments and may not provide adequate protection to

radio reception in such environments.

Korea (KCC) ...........................Class A equipment (Industrial

Broadcast & Communications

Equipment)

Class A: Equipment meets requirements for industrial

electromagnetic wave equipment and the seller or user should

take notice of it. This equipment is intended for use in business

environments and not to be used in homes.

USA (FCC)...............................47 CFR 15 subpart B. This product is

considered an exempt device per

clause 15.103.

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

LIMITED WARRANTY

This Fluke product will be free from defects in material and

workmanship for 1 year from the date of purchase. This warranty

does not cover fuses, disposable batteries, or damage from

accident, neglect, misuse, alteration, contamination, or abnormal

conditions of operation or handling. Resellers are not authorized

to extend any other warranty on Fluke’s behalf. To obtain service

during the warranty period, contact your nearest Fluke authorized

service center to obtain return authorization information, then

send the product to that Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,

ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.

Since some states or countries do not allow the exclusion or

limitation of an implied warranty or of incidental or consequential

damages, this limitation of liability may not apply to you.

11/99

1.888.610.7664sales@GlobalTestSupply.com Fluke-Direct.com

Inhaltsverzeichnis

Andere Fluke Messgerät Handbücher

Fluke

Fluke PLS 3X360R Bedienungsanleitung

Fluke

Fluke a3001 FC Bedienungsanleitung

Fluke

Fluke ScopeMeter 225C Bedienungsanleitung

Fluke

Fluke 377 Gebrauchs- und Pflegehandbuch

Fluke

Fluke FIBER QUICKMAP Bedienungsanleitung

Fluke

Fluke RUSKA 2482 Bedienungsanleitung

Fluke

Fluke i800 Bedienungsanleitung

Fluke

Fluke 1736 Konfigurationshandbuch

Fluke

Fluke VT650 Bedienungsanleitung

Fluke

Fluke 301D Bedienungsanleitung

Fluke

Fluke 345 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 789 Gebrauchs- und Pflegehandbuch

Fluke

Fluke TS52PRO Bedienungsanleitung

Fluke

Fluke 317 Bedienungsanleitung

Fluke

Fluke endurance series Bedienungsanleitung

Fluke

Fluke 1550B Bedienungsanleitung

Fluke

Fluke NORMA 4000 Operators Bedienungsanleitung

Fluke

Fluke 945 Bedienungsanleitung

Fluke

Fluke Comark Diligence 600 Bedienungsanleitung

Fluke

Fluke ASM-990 Series Bedienungsanleitung

Fluke

Fluke FL700G01 Bedienungsanleitung

Fluke

Fluke 8808A Gebrauchs- und Pflegehandbuch

Fluke

Fluke 336 Technisches Handbuch

Fluke

Fluke 845AR Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

Fluke i100 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken