Fluke 113 Bedienungsanleitung

Model 113 English Instruction Sheet

Page 1

113

Electrical Multimeter

Instruction Sheet

Safety Information

A Warning statement identifies hazardous conditions and actions

that could cause bodily harm or death.

A Caution statement identifies conditions and actions that could

damage the Meter or the equipment under test.

To avoid possible electric shock or personal injury,

follow these guidelines:

•Use the Meter only as specified in this instruction sheet

or the protection provided by the Meter might be

impaired.

•Do not use the Meter or test leads if they appear

damaged, or if the Meter is not operating properly.

•Always use proper terminals, switch position, and range

for measurements.

•Verify the Meter's operation by measuring a known

voltage. If in doubt, have the Meter serviced.

•Do not apply more than the rated voltage, as marked on

Meter, between terminals or between any terminal and

earth ground.

•Use caution with voltages above 30 V ac rms, 42 V ac

peak, or 60 V dc. These voltages pose a shock hazard.

•Disconnect circuit power and discharge all high-voltage

capacitors before testing resistance, continuity, diodes,

or capacitance.

PN 3083192 December 2007, Rev. 1, 12/08

Specifications subject to change without notice. Printed in China

Model 113 English Instruction Sheet

Page 2

•Do not use the Meter around explosive gas, vapor or in

damp or wet environments.

•When using test leads or probes, keep your fingers

behind the finger guards.

•Only use test leads that have the same voltage,

category, and amperage ratings as the meter and that

have been approved by a safety agency.

•Remove test leads from Meter before opening the

battery door or Meter case.

•Comply with local and national safety requirements

when working in hazardous locations.

•Use proper protective equipment, as required by local or

national authorities when working in hazardous areas.

•Avoid working alone.

•Check the test leads for continuity before use. Do

not use if the readings are high or noisy.

Model 113 English Instruction Sheet

Page 3

Symbols

JEarth ground TDouble Insulated

XHazardous voltage YHazardous voltage

Battery (Low battery

when shown on the

display.)

Important Information; Refer

to manual

CAT III

IEC Measurement

Category III – CAT III

equipment is designed to

protect against transients

in equipment in fixed

equipment installations,

such as distribution

panels, feeders and short

branch circuits, and

lighting systems in large

buildings.

CAT IV

IEC Measurement Category

IV – CAT IV equipment is

designed to protect against

transients from the primary

supply level, such as an

electricity meter, overhead or

underground utility service.

~Do not dispose of this product as unsorted municipal waste. Go

to Fluke’s website for recycle information.

Terminals

COM

LOW IMPEDANCE

600 V

300 V

CAT

fda09.eps

No. Description

ACommon (return) terminal for all measurements.

BInput terminal for all measurements.

Model 113 English Instruction Sheet

Page 4

Automatic Range Selection

The meter defaults to autoranging when turned on. To return to

autoranging while in the manual range mode, press qfor 1 second.

Manual Range Selection (kCHEK, Ωand E)

See each function in this instruction sheet for available ranges.

RANGE

fda01.eps

Model 113 English Instruction Sheet

Page 5

Battery Saver

™

(Sleep Mode)

If the Meter is ON, but inactive and not connected to voltage for

more than 20 minutes, the display goes blank to preserve battery

life. To resume operation, press any button or turn the rotary

switch. To disable the Sleep Mode, refer to the Power-Up

Options section.

Sleep Mode is always disabled in MIN/MAX record mode.

Backlight

Press Qto toggle the backlight on and off. The backlight

automatically turns off after 40 seconds. To disable backlight

auto-off, refer to the Power-Up Options section.

Display Hold

XWWarning

To avoid electric shock, when Display HOLD is

activated, be aware that the display will not change

when you apply a different voltage.

In the Display HOLD mode, the Meter freezes the digital display.

1. Press fto activate Display HOLD. (Kis displayed.)

2. To exit and return to normal operation, press for turn the

rotary switch.

Model 113 English Instruction Sheet

Page 6

Power-Up Options

To select a Power-Up Option, hold down the button indicated in

the following table while turning the Meter from off to the kCHEK

function. Power-Up Options are canceled when you turn the

Meter off and when sleep mode is activated.

Button Power-Up Options

fTurns on all display segments until the button is released.

pDisables beeper. bEEP is displayed when enabled.

qTurns on all display segments until the button is released.

gDisables Sleep mode. PoFF is displayed when enabled.

QDisables auto backlight off. LoFF is displayed when

enabled.

Model 113 English Instruction Sheet

Page 7

WkCHEK

If a dc or ac voltage greater than about 3 V is present across the inputs

when the meter is set to kCHEK, the meter switches automatically to dc

or ac voltage mode and displays the voltage.

When kCHEK is activated, the meter has low input impedance (LoZ)

≅3 kΩ. This load can alter the voltages in electronic control circuits. Do

not use kCHEK to measure voltage in circuits that could be damaged by

a 3 kΩload.

Note

CHEK can be effectively used to eliminate “ghost”

voltages.

AC and DC Voltage

Also refer to kChek.

Volts

Input Impedance ≅3 kΩ

AC forAC Voltage

DC forDC Voltage

60 V6 V 600 V

RANGE

fda02.eps

Model 113 English Instruction Sheet

Page 8

Diode Test G

Turn off circuit power before testing. For best results, diodes

should be measured out of circuit.

Also refer to kCHEK.

Good Diode

Forward Bias

Single

Beep

Reverse Bias

Good Diode Good Diode

fda03.eps

Bad Diode

Shorted

and

Open

Bad Diode Bad Diode

fda04.eps

Model 113 English Instruction Sheet

Page 9

Continuity s

Turn off circuit power before testing.

OpenShort

fda05.eps

Continuity Capture

Turn off circuit power before testing.

MIN MAX

fda06.eps

Model 113 English Instruction Sheet

Page 10

Short Open

Short to Open Open to Short

fda10.eps

Captures transitions longer than 500 μs (1/2000th of a second).

Transitions after the first transition cause the Meter to beep, but

the display does not change.

To reset the display to the current condition, press p.

To exit, press pfor 2 seconds, or turn the rotary switch.

Andere Handbücher für 113

Inhaltsverzeichnis

Andere Fluke Multimeter Handbücher

Fluke

Fluke 287 Bedienungsanleitung

Fluke

Fluke 11/12 Bedienungsanleitung

Fluke

Fluke 8010A Bedienungsanleitung

Fluke

Fluke 8030A Bedienungsanleitung

Fluke

Fluke 27-II Gebrauchs- und Pflegehandbuch

Fluke

Fluke 110 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 116 Bedienungsanleitung

Fluke

Fluke 374 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 8020A Bedienungsanleitung

Fluke

Fluke 8842A Bedienungsanleitung

Fluke

Fluke 116C Bedienungsanleitung

Fluke

Fluke 1630 Gebrauchsanweisung

Fluke

Fluke 114 Bedienungsanleitung

Fluke

Fluke 45 Bedienungsanleitung

Fluke

Fluke 27-II Bedienungsanleitung

Fluke

Fluke 91 Series II Bedienungsanleitung

Fluke

Fluke 116 Bedienungsanleitung

Fluke

Fluke 88 V Bedienungsanleitung

Fluke

Fluke 1587 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 88 V Bedienungsanleitung

Fluke

Fluke 8021B Bedienungsanleitung

Fluke

Fluke 8050A Bedienungsanleitung

Fluke

Fluke 8505A Bedienungsanleitung

Fluke

Fluke CNX 3000 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Bedienungsanleitung