Fluke T50 Bedienungsanleitung

Model T50

Voltage/Continuity

Tester

Users Manual

PN 2438510

May 2005

Printed in China.

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

References marked on instrument or in the

instruction manual:

Warning of potential danger, comply

with instruction manual.

Reference. Please use utmost attenti-

on.

Caution! Dangerous voltage.Danger of

electrical shock.

Continuous double or reinforced insu-

lation complies with category II IEC

61140.

Insulated personnel body protective

equipment up to 690V

Conformity symbol, the instrument

complies with the valid directives. It

complies with the EMV Directive

(89/336/EEC) and the Low Voltage Di-

rective (73/23/EEC).

The instruction manual contains infor-

mation and references, necessary for

safe operation and maintenance of the

instrument. Prior to using the instru-

ment, read the instruction manual and

comply with it in all sections.

Failure to read the instruction manual

or to comply with the warnings and re-

ferences contained herein can result in

serious bodily injury or instrument da-

mage.

Introduction / Scope of Supply

The FLUKE T50 instruments are voltage

and continuity testers for universal applica-

tions. The voltage testers are constructed

in accordance with the newest safety pres-

criptions and guarantee safe and reliable

measurement and testing.The voltage tes-

ters represent a valuable support for all

testing and measurement in handicraft and

Fluke T50

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

industrial applications as well as for house-

hold uses.

The voltage testers FLUKET50 characteri-

sed by the following features:

• Constructed in compliance with DIN EN

61243-3, DINVDE 0682 Part 401 (previo-

usly DIN VDE 0680 Part 5), IEC61010

• DC and AC voltage measurement up to

690V

• Single-pole phase test

• Continuity test / diode test

After unpacking, verify that the instrument

is undamaged. The scope of supply com-

prises:

1 FLUKE T50

2 Batteries 1.5V IEC LR03 AAA

1 Instruction manual

Safety Measures

The FLUKE T50 instrument has been con-

structed and verified in compliance with the

safety measures for voltage testers DIN EN

61243-3, DIN VDE 0682 Part 401 (previo-

usly DINVDE 0680 Part 5), EN 61010, and

IEC 61010 and have left the factory in safe

and perfect condition.

In order to avoid electrical shock, the

valid safety andVDE regulations regar-

ding excessive contact voltages must

receive utmost attention, when working

with voltages exceeding 75V (60V) DC

or 50V (25V)rms AC.The values in bra-

ckets are valid for special ranges (for

example medicine and agriculture).

Prior to measurement ensure that the

test leads and the test instrument are

in perfect condition.

Fluke T50

Safety Measures

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

When using this instrument only the

handles of the probes may be touched .

This instrument may only be used wit-

hin the ranges specified (seeTechnical

Data) and within voltage systems up to

690V.

Prior to usage, ensure perfect instru-

ment function (e.g. on known voltage

source).

The voltage testers may no longer be

used if one or several functions fail or if

no functionalityis indicated.

Do not measure under damp conditi-

ons.

Perfect display is only guaranteed wit-

hin a temperature range of -10°C up to

+ 55°C, at relative humidity <85%.

If operator’s safety cannot be guaran-

ted, the instrument must be removed

from service and protected against

use.

The safety can no longer be ensured if the

instrument:

• shows obvious damage

• does not carry out the desired measure-

ments

• has been stored for too long under unfa-

vourable conditions

• has been subjected to mechanical stress

during transport. All relevant statutory

safety regulations must be adhered to

when using this instrument.

Fluke T50

Safety Measures

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Appropriate Usage

The instrument may only be used under

those conditions and for those purposes for

which it was built. For this reason, the

safety references, the technical data inclu-

ding environmental conditions and the

usage in dry environments must be follo-

wed.

When modifying or changing the in-

strument, the operational safety is no

longer ensured.

The instrument may only be opened by

an authorized service technician, e.g.

for fuse replacement.

Control Elements

Handle test probe - (L1)

Instrument test probe + (L2)

LEDs for voltage display

LED for single-pole phase test

LED for continuity

Polarity indication

Battery case

Fluke T50

Users Manual

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Measurements

Safety Measures

For any test (measurement) the safety

references must be respected. Prior to

any use, a functional test has to be car-

ried out.

Function test / Self test:

• Test the voltage tester on a known

source.

• Connect test probes. An acoustic sound

must be audible and the LED Rx/Ω(5)

must be illuminated.

The voltage testers may no longer be

used if one or several functions fails or

if no functional reliability can be de-

tected.

The voltage display of the FLUKE T50

instruments also functions when using

discharged or no batteries.

The FLUKE T50 instrument are equipped

with an internal load enabling the tripping

of an RCD protection device of 10mA or

30mA.

For voltage tests (L towards PE) in sys-

tems with RCD devices, the RCD may

be triggered. To avoid RCD tripping

first test between L and N (approx. 5s).

Immediately afterwards testing L to-

wards PE can be carried out without

RCD tripping.

Fluke T50

Users Manual

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Voltage Test

Safety measures have to be met

• Connect both test probes with UUT.

From a voltage of > 12V the voltage

tester switches on automatically.

• The voltage is indicated by LED (3)

• For AC voltages the ”+” and ”-” LEDs are

illuminated and an additional signal

sound is audible.

• For DC voltages the LED (6) is illumina-

ted or a sound is audible.

• The instruments are equipped with an

LED row comprising: 12V, 24V, 50V,

120V, 230V, 400V, 690V.

• For DC voltage, the polarity of the volta-

ge displayed refers to the instrument test

probe (+).

Single-Pole Phase Test

The single-pole phase test starts at an

AC voltage of approx. 100V (pole >

100V AC).

When using single-pole phase tests to

determine external conductors, the

display function may be impaired

under certain conditions (e.g. for insu-

lating body protective equipment on

insulation locations).

The single-pole phase testing is not

appropriate to determine whether a

line is live or not.For this purpose, the

double-pole voltage test is always re-

quired.

A signal sound indicates the phase.

The LED (4) is illuminated in the dis-

play.

Fluke T50

Users Manual

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Voltage Test with RCD Trip

Test

During voltage tests in systems equipped

with RCD circuit breakers, a RCD switch

can be tripped at a nominal residual cur-

rent of 10mA or 30mA by measuring the

voltage between L and PE.

The RCD trips.

To avoid RCD tripping, a test has to be car-

ried out between L and N during approx. 5

seconds. Immediately afterwards, voltage

testing between L and PE can be carried

out without RCD tripping.

Continuity Test

Make sure that UUT is not live. Test

voltage polarity at handle test probe is

positive (+).

• Check that UUT is not live by carrying out

a double-pole voltage test.

• Connect both test probes with UUT.A sig-

nal sound is audible for continuity and the

LED for continuity Rx/Ω(5) is illuminated.

Maintenance

When using FLUKET150 testers in compli-

ance with the instruction manual, no parti-

cular maintenance is required. If functional

errors occur during normal operation, stop

using it and contact your nearest authori-

zed service center.

Fluke T50

Users Manual

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Cleaning

Prior to cleaning, remove voltage tester

from all measurement circuits. If the instru-

ment is dirty after daily usage, it is advise-

able clean it by using a damp cloth and a

mild household detergent. Never use acid

detergents or dissolvents for cleaning.

After cleaning, do not use the voltage tes-

ter for a period of approx.5 hours.

Calibration Interval

The voltage testers must be calibrated pe-

riodically and checked by our service de-

partment at regular intervals to ensure the

specified accuracy of measurement re-

sults.We recommend a calibration interval

of one year.

Battery Replacement

If no signal sound is audible when shorting

the test probe sproceed with the battery re-

placement.

• Completely disconnect FLUKE T50 from

the measurement circuit.

• Turn the screw (left) in the case (down,

direction of the arrow). Then open and

remove it.

• Remove discharge batteries.

• Replace with new batteries, type 1.5V IEC

LR03 AAA respecting correct polarity.

• Insert the battery case and close it.

Fluke T50

Users Manual

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Please consider your environment when

you dispose of your one-way batteries.

They belong in a trash dump for hazardous

waste. In most cases, the batteries can be

returned to their point of sale.

Please, comply with the respective

valid regulation regarding the return,

recycling and disposal of used batte-

ries and accumulators.

Technical Data

LED voltage range 12...690V AC/DC

LED resolution ±12, 24, 50, 120, 230, 400,

690V

Tolerance complying to DIN VDE 0682,

Part 401

Voltage detection automatic

Acoustic signal (AC voltage) yes

Polarity detection full range

Range detection automatic

Response time <0.1s LED

Frequency range DC, 0...65 Hz

Automatic load (RCD) yes

Internal basic load approx. 2.1 W at 690V

Test current < 3,5 mA

Peak current Is = 0.2 A

Operation time ED (DT) = 30s

Recovery time 240 s

Auto Power On > 12 V AC/DC

Single-pole Phase Test

Voltage range 100...690 V AC

Frequency range 50...65 Hz

Continuity Test

Resistance range 0...200 kΩ

Accuracy RN +50%

Test current 3 µA

Overvoltage protection690V AC/DC

Power supply 2 x 1.5 V Micro IEC LR03

Power consumption max. 30mA / approx. 250mW

Temperature range -10°C...55°C

Humidity max. 85% relative humidity

Height above sea levelup to Tm

Overvoltage class CAT III / 600 V

Degree of contamination2

Type of protection IP54

Safety complying to DIN EN 61243-3, DIN VDE

0682 Part 401 (first DIN VDE

0680 Part 5, EN 61010, IEC

61010)

Weight 130g (incl. batteries)

Dimensions (HxWxD) 210 x 40 x 22 mm

Fluke T50

Technical Data

ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ

+7 (495) 109-02-08 [email protected] www.bbrc.ru

Inhaltsverzeichnis

Andere Fluke Prüfgeräte Handbücher

Fluke

Fluke DTX-CLT CertiFiber Bedienungsanleitung

Fluke

Fluke 5700A Series II Service Bedienungsanleitung

Fluke

Fluke 6055 Bedienungsanleitung

Fluke

Fluke 1537-II Bedienungsanleitung

Fluke

Fluke T100 Bedienungsanleitung

Fluke

Fluke 730G Bedienungsanleitung

Fluke

Fluke 5560A Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Fluke

Fluke 726 Bedienungsanleitung

Fluke

Fluke ULT800 Bedienungsanleitung

Fluke

Fluke 9009 Bedienungsanleitung

Fluke

Fluke 714B Bedienungsanleitung

Fluke

Fluke BT5300 Series Bedienungsanleitung

Fluke

Fluke 3130-G2M Bedienungsanleitung

Fluke

Fluke MicroNetBlink Kit Bedienungsanleitung

Fluke

Fluke Fiber OneShot PRO Bedienungsanleitung

Fluke

Fluke ScopeMeter 190 Series III Bedienungsanleitung

Fluke

Fluke ScopeMeter 190B Series Bedienungsanleitung

Fluke

Fluke 1507 Bedienungsanleitung

Fluke

Fluke TS54 Bedienungsanleitung

Fluke

Fluke 1550C Gebrauchsanweisung

Fluke

Fluke NetDAQ 2640A Bedienungsanleitung

Fluke

Fluke CombiScope PM3370B Bedienungsanleitung

Fluke

Fluke 1503 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung