Fortin FSA-206 Bedienungsanleitung

1User guide

TABLE OF CONTENTS

INTRODUCTION ......................................................................................................................................................................................2

USING THE REMOTE CONTROL..................................................................................................................................................................2

WARNING.............................................................................................................................................................................................. 2

WARNING..................................................................................................................................................................................2

REMOTE-STARTING .................................................................................................................................................................................3

REMOTE-STARTING THE VEHICLE..........................................................................................................................................3

ACCESSORY PRESET ...............................................................................................................................................................3

READY MODE (MANUAL TRANSMISSION ONLY)............................................................................3

DRIVING OFF ............................................................................................................................................................................. 4

CANCELLING A REMOTE START............................................................................................................................................. 5

REMOTE-STARTER FEATURE’S .................................................................................................................................................................. 5

IDLE MODE (AUTOMATIC TRANSMISSION).......................................................................................................................... 5

IDLE MODE (MANUAL TRANSMISSION)...............................................................................................................................5

TURBO MODE (AUTOMATIC TRANSMISSION) ..................................................................................................................... 6

TURBO MODE (MANUAL TRANSMISSION) ..........................................................................................................................6

VALET MODE (VIA SWITCH) / VALET CODING..................................................................................................................... 7

VALET MODE (VIA REMOTE) ................................................................................................................................................... 8

2-WAY REMOTE CONTROL (IF EQUIPPED)...................................................................................................................................................8

5 BUTTON FUNCTIONALITY....................................................................................................................................................9

2-WAY REMOTE CONTROL RESPONSE (LED AND SPEAKER) ...........................................................................................9

ALARM SYSTEM (IF EQUIPPED)............................................................................................................................................. 9

VEHICLE STATUS QUERY ......................................................................................................................................................10

COLD START TIMER MODE ................................................................................................................................................... 10

AUXILIARY USE (5 BUTTON TRANSMITTER ONLY)........................................................................................................... 10

MULTI-VÉHICLE MODE...........................................................................................................................................................11

REMOTE STARTING OPTIONS .................................................................................................................................................................11

CONFIGURABLE FONCTIONALITY DURING INSTALLATION..............................................................................................11

REMOTE DOOR LOCKS ..........................................................................................................................................................12

ACTIVE OR PASSIVE ARMING............................................................................................................................................... 12

IGNITION DOOR LOCKS..........................................................................................................................................................12

SECURITY LOCK...................................................................................................................................................................... 12

TRUNK/HATCH RELEASE ZONE 6.......................................................................... 12

RUNTIME ................................................................................................................................................................................. 13

RUNTIME RESET (5 BUTTON TRANSMITTER ONLY)......................................................................................................... 13

SECURE TRANSMITTER MODE............................................................................................................................................. 13

ALARM................................................................................................................................................................................................13

AUDIBLE CONFIRMATION .....................................................................................................................................................13

ALARM ACTIVITY.................................................................................................................................................................... 13

OPEN ZONE NOTIFICATION................................................................................................................................................... 13

FALSE ALARM DEACTIVATION .............................................................................................................................................14

SHOCK SENSOR (ZONE 4) ....................................................................................................................................................14

VEHICLE LOCATOR/PANIC MODE .......................................................................................................................................14

SENSOR DEACTIVATION .......................................................................................................................................................14

TRANSMITTER RANGE........................................................................................................................................................................... 14

FAILED REMOTE-START..........................................................................................................................................................................14

REMOTE START / ALARM DIAGNOSTICS .................................................................................................................................................. 15

REMOTE STARTER DIAGNOSTICS .................................................................................................................................................... 15

ALARM DIAGNOSTICS....................................................................................................................................................................15

User guide 2

INTRODUCTION

This guide contains all the information relevant and necessary for the use of this

module. This is a state of the art Remote-Starter/Alarm system including numerous

new comfort and security features, and all of the elementary features generally offered

with most basic Remote-Starter systems. This system contains transmitter(s) and a

receiver with 750m/2500ft range. Most of the installation requirements and

programming of this product are explained in the Installation Guide. Therefore, if you

need detailed information regarding the installation or a specific programming feature

of the product, we recommend that you refer to the Installation Guide.

USING THE REMOTE CONTROL

The transmitter functions are as follows :

START

Remote-start the vehicle,

Remote stop the vehicle (4 button only).

LOCK

Locks all doors, arm the anti-theft system and

activates the Alarm (if installed).

UNLOCK

Unlocks all doors, disarms the anti-theft system

and deactivates the Alarm (if installed).

TRUNK

Opens the trunk, and deactivates the Alarm (if

installed). The Alarm ignores the trunk zone until

it is closed.

AUX + AUXILLIARY + START

Remote Stop the vehicle. (5 button only).

AUX + AUXILLIARY + LOCK

Auxiliary 1 (5 button only).

AUX + AUXILLIARY + UNLOCK

Auxiliary 2 (5 button only).

Note: The 5 button remote(s) has the same characteristics of the 4 button remote(s)

with the exception of button placement and the addition of an auxiliary button. (See

Auxiliary Use p.9, Runtime Reset p.11).

WARNING

Your system is provided with a hood pin safety switch which is located in the engine

compartment. When the hood is opened the switch will disable the remote-starter and

prevent it from remote-starting.

Have a qualified technician verify the functionality of the hood switch every 3 to 6

months to ensure it remains in good condition.

The manufacturer is not responsible for a defective or poorly maintained hood pin

switch. Ensure that the hood pin switch is installed by a qualified technician.

WARNING

•Do not start the vehicle indoors (garage, underground parking).

•Manual transmission vehicles: do not remote-start the vehicle with a

passenger inside.

•When servicing the vehicle enable VALET MODE (See P.7).

3User guide

REMOTE-STARTING

REMOTE-STARTING THE VEHICLE

This Remote-Starter supports both manual and automatic transmission vehicles. For

manual transmission vehicles see the Ready Mode section. To remote-start the vehicle

press the (START) button for approximately 1 second. The parking lights will turn

on to indicate a response to the Remote-Start signal. Approximately 5 seconds later the

engine will crank. Once the vehicle starts the parking lights will turn on and remain on for

the entire duration of the Remote-Starter runtime, or until the Remote-Starter is shut

down. If the vehicle fails to start on the first attempt, the Remote-Starter will wait 3

seconds before it will attempt to start the vehicle again. The Remote-Starter will attempt to

start the vehicle 3 times (default) before giving up. (See Failed Remote Start p.14)

ACCESSORY PRESET

Heater & Heated Seat(s): When leaving the vehicle it is recommended that the driver pre-set

the climate controls in preparation for a later Remote-Start. When the vehicle Remote-

Starts, the current (or last) setting for the climate controls, windshield wipers (and other

accessories) will be used. When setting the blower motor (fan speed) and heated seats

(if equipped) should not be left on HIGH. It is recommended to leave these settings on

either a LOW or MEDIUM setting.

Windshield Wipers & Radio & Headlights: Some vehicles require the radio, windshield wiper,

headlight circuits to become energized while running under Remote-Start. When leaving

the vehicle you must ensure that the windshield wiper and headlight switches are turned

off. Leaving the headlights on with some vehicles could cause them to remain on even

after the Remote-Starter has shut down, resulting in a dead battery.

Rear Defrost: On most vehicles the Rear Defrost can only be activated after the vehicle has

been started and in most cases this feature is not included with a Remote-Starter

installation. On some vehicles it may be possible for the installer to hook this feature up

so it either automatically enables after Remote-Start or can be enabled by using an AUX

output. (See Auxiliary Outputs p.10)

Driver Presets: Some vehicles retain different seat, mirror and radio settings for each driver.

Different driver presets are not controlled by the Remote-Starter, however they may be

controlled with the Bypass/Interface Kit.

READY MODE (MANUAL TRANSMISSION ONLY)

Two activation methods are possible, please consult the salesman or installer to

determine which of these modes applies to your vehicle.

There are always safety concerns for a manual transmission vehicle to accidentally start

while in gear, Ready Mode alleviates these concerns. The driver must enable Ready

Mode in order to Remote-Start the vehicle at a later time. Once Ready Mode is setup

the vehicle can be started/stopped at will, as many times as needed. However once the

parking brake is disengaged, the hood is opened, or any of the doors are opened, Ready

Mode will deactivate and the vehicle will not start until Ready Mode is reactivated.

MODE 1 ACTIVATION :

STEP 1

and

Make sure that all doors are closed and the transmission

is in the NEUTRAL position.

STEP 2

Engage the parking brake.

STEP 3

Release the brake pedal.

STEP 4

Within 20 seconds push the (START) button.

The parking lights will flash once and then remain on.

User guide 4

STEP 5

Remove the key from the ignition barrel.

The vehicle will remain running with the Remote-Starter.

STEP 6

Exit the vehicle and close all of the doors.

The Remote-Starter will stop running once all the doors are

closed.

STEP 7

Lock the doors by pushing the . (LOCK) button.

To deactivate Ready Mode:

• Open any door(s) • Open the hood

• Disengage of the parking brake

Note : If the parking lights flash 3 times when Remote-Starting, Ready Mode is not enabled.

MODE 2 ACTIVATION :

STEP 1

Make sure the transmission is in the NEUTRAL position.

STEP 2

Engage the parking brake.

STEP 3

Release the brake pedal.

STEP 4

Remove the key from the ignition barrel. The engine will shut

down and the vehicle will be ready to start at any time.

STEP 5

Lock the doors by pushing the . (LOCK) button.

To deactivate Ready Mode:

• Transmission is put in gear (not neutral) • Open the hood

• Disengage of the parking brake

Note : If the parking lights flash 3 times when Remote-Starting, Ready Mode is not enabled.

DRIVING OFF

When the vehicle is running with the Remote-Starter, enter the vehicle and proceed with

the following steps:

STEP 1

Insert the key and turn it to the ignition (ON/Run) position.

WARNING: Do not turn the key to the START position when the

engine is running. This may damage the ignition system on

some vehicles.

STEP 2

Step on the brake pedal to disable the Remote-Starter, and put

the vehicle in gear.

5User guide

CANCELLING A REMOTE START

If the vehicle is running with the Remote-Starter and you want to shut down the vehicle

proceed with the following steps:

4 BUTTON

TRANSMITTER

Press the START button of the transmitter.

5 BUTTON

TRANSMITTER

First press the AUX button (the light will flash slowly),

then within 12 seconds press the START button

(the light will flash rapidly).

REMOTE-STARTER FEATURE’S

IDLE MODE (AUTOMATIC TRANSMISSION)

Idle Mode allows the vehicle to run without the key in the ignition barrel. For example, if

you stop for a quick errand or delivery, simply allow the vehicle to run while you are gone.

The engine will run until the Remote-Starter runtime expires. Press START any time the

vehicle is running with the Remote-Starter to reset this timer. To activate Idle Mode

(automatic transmission) proceed with the following steps:

STEP 1

With the key in the barrel at the ignition (ON/RUN) position and

the engine running, press the (START) button, until the

parking lights turn on.

STEP 2

Turn the key to the OFF position and remove the key from the

ignition barrel. The vehicle will continue to run with the the

Remote-Starter.

STEP 3

Get out of the vehicle and press the (LOCK) button to lock the

doors. The engine will run until the Remote–Starter runtime

expires.

WARNING : Never leave children or animals in a Remote-Started vehicle unattended.

IDLE MODE (MANUAL TRANSMISSION)

Idle mode is activated in much the same way Ready Mode is activated, except for Step 1.

To activate Idle Mode (manual transmission) proceed with the following steps:

Idle Mode Activation :

STEP 1

and

Open at least one door and ensure the transmission is in

the NEUTRAL position.

STEP 2

Engage the parking brake.

User guide 6

STEP 3

Release the brake pedal.

STEP 4

Within 20 seconds push the (START) button.

The parking lights will flash once and then remain on.

STEP 5

Remove the key from the ignition barrel.

The vehicle will continue to run with the the Remote-Starter.

STEP 6

Exit the vehicle and close all of the doors.

The vehicle will continue to run after all the doors are

closed.

STEP 7

Lock the doors by pushing the . (LOCK) button.

The engine will continue to run until either the transmitter (STOP) button is pressed, the

Remote-Starter runtime expires, the parking brake is disengaged, the brake is pressed, or

the hood is opened. If the Remote-Starter is shut down by transmitter it will automatically

go in to Ready Mode (if all the doors are closed).

WARNING : Never leave children or animals in a Remote-Started vehicle unattended.

TURBO MODE (AUTOMATIC TRANSMISSION)

Turbo Mode (if installed) is similar to Idle Mode but is used to cool down the turbo-charger

once the driver leaves the vehicle. The Remote-Starter will continue run the vehicle for 2

minutes allowing the turbo-charger to cool down. To activate Turbo Mode (automatic

transmission) proceed with the following steps:

STEP 1

With the engine already running, push the (START)

button until the parking lights come on.

STEP 2

Remove the key from the ignition barrel.

The vehicle will continue to run with the the Remote-Starter.

STEP 3

Exit the vehicle and close all of the doors.

The vehicle will continue to run after all the doors are closed.

STEP 4

Press the . (LOCK) button to lock the doors.

The vehicle will continue to run for 60 seconds

TURBO MODE (MANUAL TRANSMISSION)

Turbo Mode (if installed) is similar to Idle Mode but is used to cool down the turbo-charger

once the driver leaves the vehicle. The Remote-Starter will continue run the vehicle for 60

seconds allowing the turbo-charger to cool down. To activate Turbo Mode (manual

transmission) proceed with the following steps:

ÆSee IDLE MODE (MANUAL TRANSMISSION) page 5.

7User guide

VALET MODE (VIA SWITCH) / VALET CODING

Valet Mode disables both the Remote-Starter and Alarm system. Whenever the vehicle is

being serviced or repaired, or the vehicle is parked indoors it is mandatory that Valet Mode

be enabled to prevent an accidental Remote-Start.

Note: The alarm system is not active (including Starter Kill) when the system is in Valet

Mode. However you are still able to lock and unlock the doors, and release the rear

hatch/trunk.

Note: When the Remote-Starter/Alarm is in Valet Mode, the LED will stay ON solid instead

of flashing after the doors are locked. The LED will turn off only after the Remote-

Starter/Alarm exit Valet Mode.

The valet mode can be programmed to use a coded entry in order to increase the security

of your alarm system and to prevent accidents. By default, the valet button is pressed 3

times after turning the ignition. Function 30 can be programmed to use a coded value

instead of the default one.

VALET CODING DISBALED (DEFAULT):

To activate and deactivate Valet Mode using the valet switch proceed with

the following steps:

STEP 1

Insert the key and turn it to the ignition (ON/RUN)

position. The vehicle does not need to be started.

STEP 2

Within 10 seconds press (1 second) and release the

Valet switch 3 times.

STEP 3

Valet mode enabled: The LED is ON

Valet mode disabled: The LED is OFF

VALET CODING ENABLED (OPTIONAL):

To activate and deactivate Valet Mode using the valet switch proceed with the following

steps:

STEP 1

Insert the key and turn it to the ignition (ON/RUN)

position. The vehicle does not need to be started.

STEP 2

Within 10 seconds press and release the valet button 3

to 7 times (X = valet code) for 1 second. If your valet

code is 7 then press and release the valet button 7

times.

STEP 3

Press and hold the valet button once for 3 seconds to

finish the sequence.

STEP 4

Valet mode enabled:The LED is ON

Valet mode disabled: The LED is OFF

Note: The coded valet option allows a selection of one of the five available codes. Once

the installer chooses one of the codes, note the value here so you do not forget

it_____________________.

User guide 8

VALET MODE (VIA REMOTE)

Valet Mode disables the remote-starter and alarm. Whenever the vehicle is being serviced

or repaired, or the vehicle is parked indoors it is mandatory that Valet Mode be enabled to

prevent an accidental Remote-Start.

Note: The alarm system is deactivated (including Starter Kill) when the system is in Valet

Mode. However you are still able to lock & unlock the doors, and release the rear

hatch/trunk. This method of enabling/disabling Valet Mode uses the remote transmitter

instead of the valet switch indicated in the preceding section.

To enter Valet Mode using the remote transmitter proceed with the following steps:

STEP 1

Simultaneously press the (LOCK) and (UNLOCK) buttons for 1

second. The parking lights will flash once.

STEP 2

The LED will turn ON solid and remain ON.

To exit Valet Mode using the remote transmitter proceed with the following

steps:

STEP 1

Simultaneously press the (LOCK) and (UNLOCK) buttons for 1

second. The parking lights will flash once.

STEP 2

The LED will turn OFF or will start to flash.

2-WAY REMOTE CONTROL (IF EQUIPPED)

The 2-way remote control is

built with the latest RF

telecommunication

technology. It is functional up

to 4000 feet (range may

vary depending on

environment). The remote

control has a multi-color

LED and a speaker to

provide both a visual and

audible confirmation of the

status of your vehicle.

9User guide

5 BUTTON FUNCTIONALITY

The functions of the buttons are described in detail within the USING THE REMOTE

CONTROL section (p.3)

2-WAY REMOTE CONTROL RESPONSE (LED AND SPEAKER)

Action

Commu-

nicating

with

The

remote-

starter.

LED

RESPONSE SPEAKER RESPONSE STATUS

1 Green

Flash 1beep LOCK succeeded

LOCK Flashing

Blue

1 Red Flash 1 low beep LOCK failed, no

communication. [1]

1 Green

Flash 2 beeps UNLOCK succeeded

UNLOCK Flashing

Blue

1 Red Flash 1 low beep UNLOCK failed, no

communication. [1]

1 Green

Flash 1 beep TRUNK succeeded

TRUNK Flashing

Blue

1 Red Flash 1 low beep TRUNK failed, no

communication. [1]

1 beep START/STOP

succeeded

Ascending notes

[2]

The vehicle has

STARTed.

1 Green

Flash

Descending notes

[2]

The remote-starter

failed to start or

shutdown normally.

START

Flashing

Blue

1 Red Flash 1 low beep

START/STOP failed

no communication.

[1]

NOTE [1]: It is possible that the remote control was able to communicate with the remote-

starter and that action was performed successfully, but the remote-starter was unable to

send its response back to the remote control. Some factors such as radio interference

may interfere with the communication between the remote control and the remote-starter.

See the TRANSMITTER RANGE (p.14) and FAILED REMOTE-START (p.14)

NOTE [2]: The response from the remote-starter may take up to 8 seconds or

longer (diesel mode).

ALARM SYSTEM (IF EQUIPPED)

If the alarm system is enabled the remote control will provide the following status

when the alarm is triggered.

LED SPEAKER STATUS

Flashing Red Oscillating tone

for 20 seconds A zone on the alarm has been triggered.

Andere Handbücher für FSA-206

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Fortin Fernstartsystem Handbücher

Fortin

Fortin EVO ALL Bedienungsanleitung

Fortin

Fortin EVO ONE Bedienungsanleitung

Fortin

Fortin E400 Bedienungsanleitung

Fortin

Fortin FTX-64-2W Bedienungsanleitung

Fortin

Fortin EVO ALL Bedienungsanleitung

Fortin

Fortin EVO ONE Bedienungsanleitung

Fortin

Fortin FMH SERIES Bedienungsanleitung

Fortin

Fortin EVO ONE Bedienungsanleitung

Fortin

Fortin EVO ONE Bedienungsanleitung

Fortin

Fortin EVO ONE Bedienungsanleitung

Fortin

Fortin ANT-FMH-2W Bedienungsanleitung

Fortin

Fortin EVO-ALL Bedienungsanleitung

Fortin

Fortin EVO-ONE FTX25 Bedienungsanleitung

Fortin

Fortin ORBIT F3400 Bedienungsanleitung

Fortin

Fortin EVO-ONE RFK912 Bedienungsanleitung

Fortin

Fortin KEY-OVERRIDE-ALL Bedienungsanleitung

Fortin

Fortin EVO ONE Bedienungsanleitung

Fortin

Fortin Evo Ride Bedienungsanleitung

Fortin

Fortin EVO-START Bedienungsanleitung

Fortin

Fortin EVO-ONE Bedienungsanleitung

Fortin

Fortin ATX5 Bedienungsanleitung

Fortin

Fortin FTX-44-2W Bedienungsanleitung

Fortin

Fortin EVO ALL Bedienungsanleitung

Fortin

Fortin KEY-OVERRIDE-ALL Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch