Fortinet FortiAP Bedienungsanleitung

FortiAP 221C

QuickStart Guide

January 28, 2014

20-000-226428-20140128

and FortiGuard®, are registered trademarks of Fortinet, Inc., and other

Fortinet names herein may also be trademarks of Fortinet. All other

product or company names may be trademarks of their respective

owners. Performance metrics contained herein were attained in internal

lab tests under ideal conditions, and performance may vary. Network

variables, different network environments and other conditions may affect

performance results. Nothing herein represents any binding commitment by

Fortinet, and Fortinet disclaims all warranties, whether express or implied,

except to the extent Fortinet enters a binding written contract, signed by

Fortinet’s General Counsel, with a purchaser that expressly warrants that the

identiﬁed product will perform according to the performance metrics herein.

For absolute clarity, any such warranty will be limited to performance in the

same ideal conditions as in Fortinet’s internal lab tests. Fortinet disclaims in

full any guarantees. Fortinet reserves the right to change, modify, transfer,

or otherwise revise this publication without notice, and the most current

version of the publication shall be applicable.

Table of Contents

Package Contents 1

Mounting Your FortiAP Unit 2

Connecting Your FortiAP Unit 4

Conﬁguring Your FortiAP Unit 5

Technical Speciﬁcations 7

LED Speciﬁcations 8

Cautions and Warnings 9

Regulatory Notices 12

Documentation and Links 14

Product License Agreement 16

This page intentionally left blank.

Package Contents

Fortinet’s FortiAP wireless thin access points deliver secure, identity-driven

WiFi client access that creates a fortiﬁed WLAN network that is centrally

managed by a FortiGate or FortiWiFi platform.

Your box contains the following:

FortiAP 221C

QuickStart Guide (with Mounting Template)

Mounting Bracket

T-Rail Mounting Hardware Kit

Wall/Ceiling Mounting Hardware Kit

Page 1

Mounting

Bracket

Wall/Ceiling Mounting

Hardware Kit

T-Rail Mounting

Hardware Kit

QuickStart Guide

FortiAP 221C

QuickStart Guide

Note: Accessories may not be exactly as shown.

Mounting Your FortiAP Unit

Page 2

Using the provided hardware, the FortiAP unit can be attached to a ceiling or wall.

To attach the unit to a ceiling or wall using the mounting bracket:

1. Attach the mounting bracket to the wall or ceiling using the Mounting Template

and the provided wall/ceiling mounting hardware kit (P3.5x32 screws and

Mounting Anchors).

2. Insert the provided P2.6x12 screws into the bottom cover of the FortiAP unit.

3. Leave enough of the screws exposed to ensure that the unit can be attached to

the mounting bracket.

If extra space is required, use the provided spacers and long screws from the

T-Rail mounting hardware kit to increase the space between the unit and the

mounting bracket.

4. Mount the FortiAP unit on the mounted mounting bracket by rotating the unit

clockwise about 90 degrees to secure it in place.

You can now proceed with connecting your FortiAP unit.

Mounting Anchor

P3.5x32 Screw

P2.6x12 Screw

Mounting Bracket

Rotate clockwise to

secure the unit in place

Installation

Template

Wall or Ceiling

Page 3

To attach the unit to a ceiling using the provided T-rail connectors:

1. Attach the T-rail connectors to the bottom cover of the FortiAP unit using the

provided P2.6x10 screws.

Two sizes of T-rail connectors are included in the mounting hardware kit: 15/16in

(2.38cm) and 9/16in (1.43cm).

If extra space is required to accommodate drop ceiling tiles, use the provided

spacers and P2.6x25 screws.

2. Line up the connected T-rail connectors with an appropriately sized rail and press

the unit onto the rail until it snaps into place.

Note: To protect your FortiAP unit from unauthorized removal, use the Kensington

Security Slot to attach a cable lock (cable lock is not included).

P2.6x25 Screw

P2.6x10 Screw

Spacer

Clip

T-rail

Kensington

Security Slot

Page 3

Page 4

Using the provided mounting hardware, attach the FortiAP unit to a wall or ceiling,

as described in the previous section.

Adequate grounding must be provided to the FortiAP unit and the PoE injector, in

compliance with your local electrical code or regulations.

Caution: This device complies with IEEE 802.3af PoE speciﬁcation. Do not use any

PoE injectors that are not IEEE 802.3af compliant as they may damage your device.

To connect the FortiAP unit:

1. Insert an Ethernet cable into the Ethernet port of the FortiAP unit.

2. Insert the other end of the Ethernet cable into your FortiGate, FortiWiﬁ, or

FortiSwitch unit.

If you are using PoE, ensure that the Ethernet cable is connected to an applicable

port on your FortiGate unit, FortiSwitch unit, or PoE injector.

3. If you are not using PoE, connect the DC plug of the optional power adapter

into the DC power jack on the FortiAP unit, and then insert the other end into an

appropriate power outlet.

Note: For FortiWiﬁ units, the wireless controller feature is only supported on units

running FortiOS 4.0 MR3 and higher.

Connecting Your FortiAP Unit

Page 5

Conﬁguring Your FortiAP Unit

The FortiAP unit is designed to require no conﬁguration in most networks. Zero

Conﬁguration mode works if the unit is directly connected to the FortiGate or

FortiWiﬁ performing the Wireless LAN Controller (WLC) functions, or on the same

layer-2 network and subnet as the FortiGate or FortiWiﬁ unit.

If the FortiAP wireless controller’s IP address cannot be determined using Zero

Conﬁguration mode, or if the network uses static IP addresses, it can be conﬁgured

to use a static IP address.

To enable the FortiAP using Zero Conﬁguration:

1. After connecting the FortiAP unit as described in the previous chapter, the unit

goes through its boot procedure and requests an IP address from the DHCP

server.

2. If the IP address is retrieved successfully, the FortiAP enters discovery mode to

locate a FortiGate or FortiWiﬁ wireless controller. The discovery modes are:

• Broadcast

• Multicast

• DHCP option 138

3. Verify that the FortiAP has successfully connected to the controller.

In the FortiGate Web-based Manager, go to WiFi Controller > Managed Access

Points > Managed FortiAP. A successfully discovered unit displays an orange

circle with a question mark.

4. Select the access point and click Edit.

5. In the State ﬁeld, select Authorize.

6. In the AP Proﬁle ﬁeld, select Change, then select a proﬁle from the list and click

OK.

The conﬁguration is downloaded from the wireless controller to the FortiAP and

the WiFi LEDs light up.

To enable the FortiAP with a static IP address:

1. Connect the FortiAP device to a separate private switch or hub, or directly connect

it to your management computer via a cross-over cable.

2. Conﬁgure the management computer to be on the same subnet as the internal

interface of the FortiAP unit:

• IP address: 192.168.1.3

• Netmask: 255.255.255.0

3. Telnet to IP address 192.168.1.2.

4. Type admin in the Name ﬁeld, leave the Password ﬁeld blank, and press Enter.

5. Conﬁgure a static IP address for the FortiAP unit and netmask & gateway

information for your network, using the following commands:

cfg -a ADDR_MODE=STATIC

cfg –a AP_IPADDR=xxx.xxx.xxx.xx

cfg –a AP_NETMASK=255.255.255.0

cfg –a IPGW=yyy.yyy.yyy.yyy

cfg –a AC_IPADDR_1=zzz.zzz.zzz.zzz

where xxx is the IP address of the FortiAP unit, yyy is the Gateway IP address and

zzz is the IP address of the FortiGate Wireless Controller.

6. Save the conﬁguration by typing the following command:

cfg –c

7. Unplug the FortiAP unit and plug it back in order for the conﬁguration to take

effect.

8. Move the FortiAP to the intended deployment location and connect the Ethernet

cable as described in the Connecting Your FortiAP Unit section.

9. Log in to the FortiGate controller Web-based Manager, and go to WiFi Controller

> Managed Access Points > Managed FortiAP. A successfully discovered unit

displays an orange circle with a question mark in the Status column.

10.Select the access point and click Edit.

11.In the State ﬁeld, select Authorize.

12.In the Edit FortiAP dialog box, select Enable Wireless Radio. Leave the remaining

settings at their default values. The conﬁguration is downloaded from the FortiGate

unit to the FortiAP device.

For more information, see the Deploying Wireless Networks Guide, available on

Fortinet’s technical documentation website, http://docs.fortinet.com.

Page 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fortinet Drahtloser Zugangspunkt Handbücher

Fortinet

Fortinet FortiAP S323CR Kurzanleitung zur Einrichtung

Fortinet

Fortinet FortiAP S322CR Betriebsanleitung

Fortinet

Fortinet FortiAP 222E Bedienungsanleitung

Fortinet

Fortinet FortiAP U431F Bedienungsanleitung

Fortinet

Fortinet FortiAP U422EV Bedienungsanleitung

Fortinet

Fortinet FortiGate 200F Series Bedienungsanleitung

Fortinet

Fortinet FortiAP U223EV Bedienungsanleitung

Fortinet

Fortinet FortiAP 231G Series Bedienungsanleitung

Fortinet

Fortinet FortiAP U231F Bedienungsanleitung

Fortinet

Fortinet FortiAP FAP-U321EV Bedienungsanleitung

Fortinet

Fortinet FAP-224E Bedienungsanleitung

Fortinet

Fortinet AP1000 Bedienungsanleitung

Fortinet

Fortinet FortiAPCam-214B Bedienungsanleitung

Fortinet

Fortinet FortiAP 14C Bedienungsanleitung

Fortinet

Fortinet FortiAP S421E Betriebsanleitung

Fortinet

Fortinet FortiAP U421EV Bedienungsanleitung

Fortinet

Fortinet OAP832E Bedienungsanleitung

Fortinet

Fortinet FortiAP 432FR Bedienungsanleitung

Fortinet

Fortinet FortiAP 421E Betriebsanleitung

Fortinet

Fortinet FortiAP S321CR Kurzanleitung zur Einrichtung

Fortinet

Fortinet FortiAP-220A Bedienungsanleitung

Fortinet

Fortinet FortiAP 831F Bedienungsanleitung

Fortinet

Fortinet FortiAP U432F Bedienungsanleitung

Fortinet

Fortinet AP400 Series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung