Four-Faith F-PM100 Bedienungsanleitung

F-PM100 Multifunctional Power Meter User Manual

F-PM100

Multifunctional Power

Meter User Manual

Product Version

Page

V1.0

Product Name：F-PM100

Total:

F-PM100

Multifunctional Power Meter

For Power Distribution System

User Manual

Version 1.0

F-PM100 Multifunctional Power Meter User Manual

1. Product Introduction

Multi-function power meter, a multi-function intelligent power meter with full power acquisition,

programmable measurement, display, RS485 digital communication and switch input, relay output,

it can complete three-phase electrical measurement (includes three-phase voltage, three-phase

current, active power, reactive power, apparent power, power factor, frequency, harmonics,

multi-rates, demand, SOE event records, etc.), four quadrant energy metering, data display,

acquisition and transmission, therefore it can be widely used in substation automation, distribution

automation, intelligent building, internal energy measurement, management, assessment for

company. Using the special measurement chip, the power meter could achieve large-screen LCD

liquid crystal display and RS-485 communication interface, communication protocol is the standard

MODBUS-RTU.

2. Technical Parameters and Indicators

Working Power Supply

220VAC±10% or 85～265VAC/DC

Working Temperature

-10℃+55℃

Storage Temperature

-40℃+70℃

Operating and storage

Humidity

5% 95%, no condensation

Insulation Grade

Meet the requirement of standard EN61010-1

Operating Frequency

50/60Hz

Product Life

≥10 years

Size

Display Panel：96mm×96mm×12mm(W×H×D)

Main Unit：96mm×96mm×75mm(W×H×D)

Weight

About 400G

Protection Grade

Operational Panel IP54, IP20 Side and Back Panel IP20

Input characteristics

Current Measurement：5A/1A

Voltage Measurement：57.5/220V (AC Phase Voltage RMS)

Input Characteristics

Breaking parameters: 5A@250VAC

Resistive load: 5A@30VDC

Communication

Communication Interface：RS485

Communication Protocal：MODBUS-RTU

Communication Rates:

1200/2400/4800/9600/19200/38400bps

Range of the Power MeterAddress：1 254

Note

：

Indicates that the function parameter is related to the order type.

F-PM100 Multifunctional Power Meter User Manual

Parameter

Accuracy

Measuring range

Voltage

0.2

0 999,999V

Current

0.2

0 49,999A

Power Factor

0.5

-1.0<|CosΦ|<+1.0

Active Power

0.5

Single-Phase：0 100MW

Total：0 300MW

Reactive Power

0.5

Single-Phase：0 100Mvar

Total：0 300Mvar

Apparent power

0.5

Single-Phase：0 100MVA

Total：0 300MVA

Electrical Degree

0.5

0 9999999.9kWh/kvarh

Frequency

0.1Hz

45 65Hz

3. Installation and Wiring

Drill a hole of 91 * 91mm on the switch cabinet panel.

Take out the Power Meter, release the the fixed bolts on both sides of Power Meter , remove

the metal fixed bracket.

Insert the Power Meter into the mounting hole from the front panel.

Insert the metal fixed bracket and screw the bolts to fix the power meter.

3.2 Definition of the Terminal block on Power Meter

Number

Code

Definition

Ia*

A Phase current line

A Phase current outlet

Ib*

B Phase current line

B Phase current outlet

Ic*

C Phase current line

C Phase current outlet

A Phase voltage

B Phase voltage

C Phase voltage

Neutral line

11*

RS485 Communication Interface

Positive

12*

RS485 Communication Interface Negative

13*

COM

Binary Input of the Public Terminal

14*

DI1

Binary Input 1

15*

DI2

Binary Input 2

16*

DI3

Binary Input 3

F-PM100 Multifunctional Power Meter User Manual

Remark: Indicates that the terminal function is related to the order type.

3.3 Typical Wiring Diagram of the Power Meter

Wiring Diagram of Three Phrase Four Wire:

Wiring Diagram of Three Phrase Three Wire:

17*

R11

Relay 1 Output

18*

R12

Relay 1 Output

19*

R21

Relay 2 Output

20*

R22

Relay 2 Output

N/-

AC power supply

220V Zero Line

L/+

AC power supply

220V live wire

F-PM100 Multifunctional Power Meter User Manual

4. Power Meter Parameter Setting

4.1 Key Functions in Setup Mode:

: When the cursor is flashing, select and confirm the function (Enter key);

: When the cursor is flashing, modify the configuration; When the cursor is flashing, switch the

parameter page (up key);

: When the cursor is flashing, turn the cursor on the same page to the left (press the left

button).

4.2 Description of the Parameter Setting

Note: Press "SET" key to enter the parameter setting interface, you can press the " " key to

directly view the current parameters of the Power Meter. When you press the " " key to view the

Power Meter parameters and it will pop up "need pswd" to indicate the need for a password to set

up.

F-PM100 Multifunctional Power Meter User Manual

Page

Content

Description

1. Password

Enter

Press "SET" key to enter into setting mode;

Press " " key, the digital cursor will flash, prompt for

the password entering , the factory default value is 0000;

Press " " key to move the cursor position, press " "

key to change the cursor value;

Press the " " key to confirm, the LCD screen

automatically jump to the next Power Meter parameter

setting page indicates that the password is correct and

can be operated continuously. Go to the electrical

parameters display page password input error, press

"SET" to re-enter the setup mode

2. Setting of

the

Communicati

Parameter

Setting of Baud Rate

When the cursor is flashing, press " " key to switch to

the communication parameter display interface;

Press " " key to enter the communication parameter

modification interface

Press the " " key to move the cursor to the

modification area of baud rate value.

The Key recurrently display 1.2K / 2.4K / 4.8K / 9.6K /

19.2K / 38.4K, the factory default value of Power Meter is

9.6K;

Setting of the Check Code

Press the " " key to move the flashing cursor to the

check code modification area

Press the " " key to recurrently display the n / O / E

check code range.

N is a 1-bit start bit, 8-bit data bits, no parity , 1 stop bit;

default is no parity;

O represents 1 bit start bit, 8 bits data bit, odd parity, 1 bit

stop bit.

E represents 1 bit start bit, 8 bits data bit, even parity, 1

bit stop bit;

Setting of the Communication Setting Address

F-PM100 Multifunctional Power Meter User Manual

The communication address range is 1 ~ 254, the factory

default communication address is 1;

Press the " " key to move the cursor to the

communication address modification area;

Press " " key to change the cursor value, then press "

" key to move the cursor position;

Press the " " key to confirm the page settings

3. Setting of

the System

Wiring

Method

The Power Meter supports both star and triangular

measurement wiring methods.

The default wiring method for the Power Meter is 3CT 3P4L:

Method 1: 3CT 3P4L

Method 2: 3CT 3P3L

Method 3: 2CT 3P3L

When no cursor is flashing, press " " to switch to the

setting page of the system wiring type ;

Press " " to start setting;

Press " " key to recurrently display 3CT 3 phase 4 wire

connection page; 3CT 3 phase 3 wire connection page;

2CT 3 phase 3 wire connection page;

Press the " " key to confirm the new wiring type.

4. PT Ratio

Setting

The Power Meter should set the correct PT ratio parameter.

The setting value range is 0 ~ 350, the instrument factory

default is 1.

For example: if used in 10kV high voltage cabinet, PT value

should be set to 100; If used in 380V low voltage switchgear,

PT value should be set to 1.

When no cursor is flashing, press " " to switch to PT

ratio setting page.

Press " " to start the setting.

Press the " " key to move the cursor, press " " key

to change the cursor value;

Press the " " key to confirm the PT ratio.

F-PM100 Multifunctional Power Meter User Manual

5. Setting of

CT Ratio

The Power Meter should set the correct CT variable ratio

parameters.

Value range of the setting is 0 ~ 5000, the factory default of

the Power Meter is 1.

For example, CT: 500/5 requires a CT value of 100.

When no cursor is flashing, press " " key to switch to CT

variation ratio setting interface;

Press " " to start the setting.

Press the " " key to move the cursor, press " " key

to change the cursor value;

Press the " " key to confirm the CT variation.

6. Time

Setting

Time Setting of the ACE series Power Meter from left to right,

from top to bottom followed by years, months, days, hours,

points.

When no cursor is flashing, press " " key to switch to

time setting page;

Press " " to start the setting;

Press " " key to move the cursor, press " " key to

change the cursor value;

Press " " to confirm the time.

7. Blacklight

Setting

Backlight time of ACE series Power Meter counts in seconds,

when the input is 060, it stands for the backlight time is 60s,

the longest backlight time is 999s.

When the cursor is flashing, press " " to switch to the

backlight time setting page;

Press " " to start the setting

Press " " key to move the cursor, press " " key to

change the cursor value;

Press " " to confirm the backlight time.

F-PM100 Multifunctional Power Meter User Manual

8. Preset the

Total Active

Power

You can manually enter the base of active power .

When no cursor is flashing, press " " to switch to the

setting page;

Press " " to start the setting;

Press " " key to move the cursor, press " " key to

change the cursor value;

After the active power value is set, press the " " key

to move the cursor to the position, press " " to

change to , press " " to save the active

power.

9. Preset the

Total

Reactive

Power

You can manually enter the base of reactive power

When no cursor is flashing, press " " to switch to the

setting page;

Press " " to start the setting;

Press " " key to move the cursor, press " " key to

change the cursor value;

After the reactive power value is set, press the " " key

to move the cursor to the position, press " " to

change to , press " " to save the reactive

power.

10. Clear the

Power

Setting

Operator could manually clear the electrical value

When no cursor is flashing, press " " to switch to the

setting page;

Press " " to start the setting;

Press " " to change to , press " " to

confirm the clearance of the electrical degree.

F-PM100 Multifunctional Power Meter User Manual

11. Settings

of the

Presentation

Mode

Power Meter enters into the presentation mode

When no cursor is flashing, press " " to switch to the

setting page;

Press " " to start the setting;

Press " " to change to , press " " to

confirm the entrance of the presentation mode.

12. Setting of

the

Password

Change

Power Meter enters into the interface of the password

change.

When no cursor is flashing, press " " to switch to the

setting page;

Press " " to start the setting;

Press " " key to move the cursor, press " " key to

change the cursor value;

After the password is set, press " " key to move

the cursor to , press " " to change the to

, then press" " to save.

13. Setting of

the Relay

Pulse Width

The relay output pulse width of the Power Meter Setting

counts in milliseconds.

The minimum pulse width of the relay is set to 100ms and the

maximum setting is 99900ms.

The factory default of the relay output pulse width is 2000ms.

When no cursor is flashing, press " " key to switch to

Press " " to start the setting;

Press " " key to move the cursor, press " " key to

change the cursor value;

Press " " to confirm the pulse width setting.

Inhaltsverzeichnis

Andere Four-Faith Messgerät Handbücher

Four-Faith

Four-Faith FPI-Hand Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung