Fox FLOAT X2 Kurzanleitung
2
sag setting
To achieve the best performance from your FOX suspension, adjust the
air pressure to attain your proper sag setting. Sag is the amount your
suspension compresses under
your weight and riding gear. Sag range
should be set to 25-30% of total shock travel.
Watch the sag setup video at ridefox.com/sagsetup
1. Start by setting the shock air pressure (psi) to match your weight in
pounds. With the air pump attached to the shock valve, slowly cycle
your shock through 25% of its travel 10 times as you reach your desired
pressure. This will equalize the positive and negative air chambers and
will change the pressure on the pump gauge.
Do not exceed 300 psi, the maximum FLOAT X2 air pressure!
2. Remove the pump.
3. Sit still on the bike in your normal riding position, using a wall or a
tree for support.
4. Pull the sag indicator o-ring up against the Dust Wiper.
5. Carefully dismount the bike without bouncing.
6. Measure the distance between the sag indicator o-ring and the
Dust Wiper. Compare your measurement to the ‘Suggested Sag
Measurements’ table.
7. Cycle the shock 10 times while adding or removing air pressure
until you reach your desired sag measurement.
3
Your shock has a 4 digit ID code on the shock body. Use this number on
the Help page at www.ridefox.com to find out more information about your
shock, including shock travel.
Suggested Sag Measurements
Travel 30% sag (Plush)
51 mm/ 2.00in 15 mm/ 0.60in
55 mm/ 2.25in 17 mm/ 0.68in
65 mm/ 2.50in 19 mm/ 0.75in
70 mm/ 2.75in 21 mm/ 0.82in
75 mm/ 3.00in 22 mm/ 0.90in
89 mm/ 3.50in 27 mm/ 1.05in
The recommended settings in this tuning guide are designed
to be a starting point, in order to get you out on your first ride
in as few steps as possible. Consult your bike manufacturer’s
instructions for setup recommendations.
As you ride and get used to your new shock, adjust your settings as needed.
Detailed information and videos can be found in the online owner’s manual.
4
Low-speed compression (LSC) adjustment
is useful to control shock performance
under rider weight shifts, G-outs, and other
slow inputs.
High-speed compression (HSC) adjustment
is useful to control shock performance
under bigger hits, landings, and square-
edged bumps.
COMPRESSION
damper adjustments
The 2-position lever is useful to make
on-the-fly adjustments to control shock
performance, and is intended to be
adjusted throughout the ride. The Open
mode utilizes your standard HSC/LSC,
preset high- and low-speed compression
settings. The preset high- and low-speed
compression adjustments only have an aect
on compression damping when the lever is
in the OPEN position. The FIRM mode has a
very firm low-speed compression setting and
is useful for climbing and sprinting.
LOW-SPEED COMPRESSION
3 MM HEX
HIGH-SPEED COMPRESSION
6 MM HEX
2 POSITION LEVER
5
REBOUND
HIGH-SPEED REBOUND
2 MM HEX
LOW-SPEED REBOUND
3 MM HEX
Low-speed rebound (LSR) adjustment is useful to control shock performance under brake
bumps, technical climbing, and o-camber cornering, when extra traction is needed.
High-speed rebound (HSR) adjustment is useful to allow the shock to recover from bigger
hits and square-edged bumps quickly enough to absorb consecutive hits. The HSR has 8 total
clicks of adjustment. When viewing the shock from the end with the HSR adjuster, rotating the
HSR adjuster clockwise slows down HSR. Rotating the HSR adjuster counter-clockwise speeds
up HSR. The HSR adjuster can be turned with a 2mm hex wrench or other similarly sized tool.
6
recommended settings
Use your air spring pressure in the table to find the suggested starting RVS
damper settings for your shock.
Turn all four damper adjusters to the closed position (full clockwise) until they
stop. Then back them out (counter-clockwise) to the number of clicks shown in
the table.
*Count clicks from Closed: 0 Clicks = Closed*
Air Spring
Pressure
Recommended
LSR setting
Recommended
HSR setting
Recommended
LSC setting
Recommended
HSC setting
90 16-18 7-8 16-18 7-8
100 15-17 7-8 16-18 7-8
110 14-16 6-7 15-17 7-8
120 13-15 6-7 15-17 7-8
130 12-14 5-6 14-16 6-7
140 11-13 5-6 14-16 6-7
150 10-12 5-6 13-15 6-7
160 9-11 4-5 13-15 6-7
170 8-10 4-5 12-14 5-6
180 7-9 4-5 11-13 5-6
190 7-9 3-4 10-12 5-6
200 6-8 3-4 9-11 4-5
210 6-8 3-4 8-10 4-5
220 5-7 2-3 7-9 4-5
230 4-6 2-3 6-8 4-5
240 3-5 2-3 5-7 3-4
250 2-4 2-3 4-6 3-4
260 2-4 1-2 2-4 3-4
270 1-3 1-2 2-4 3-4
280 1-3 1-2 2-4 2-3
290 1-3 0-1 1-3 2-3
300 1-2 0-1 1-3 2-3
7
Additional tuning options
Volume Spacers
Changing volume spacers in the shock is an internal adjustment that allows you to
change the amount of mid stroke and bottom out resistance.
If you have set your sag correctly and are using full travel (bottoming out) too
easily, then you could install more spacers to increase bottom out resistance.
If you have set your sag correctly and are not using full travel, then you could
remove spacers to decrease bottom out resistance.
Installation procedure and tuning options are available online at:
ridefox.com/ownersmanuals
SEE ADDITIONAL INFORMATION AND VIDEOS:
ridefox.com/floatx2setup
typical air spring curves
SHOCK TRAVEL
SHOCK FORCE
MAX SPACERS
(LEAST AIR VOLUME)
NO SPACER
(MOST AIR VOLUME)
FULL COMPRESSION
FULL EXTENSION
©FOX FACTORY, INC. 2019 // 1.800.FOX.SHOX
915 DISC DRIVE SCOTTS VALLEY, CA 95066 USA
TEL: 831.768.1100
605-00-222 REV B
Inhaltsverzeichnis
Andere Fox Fahrradzubehör Handbücher
Fox
Fox ELITE 2.5 Series Bedienungsanleitung
Fox
Fox 34 Talas 29 Bedienungsanleitung
Fox
Fox 34 Float 29 Bedienungsanleitung
Fox
Fox LiveValve 32 Step Cast Bedienungsanleitung
Fox
Fox DHX Air 5.0 Bedienungsanleitung
Fox
Fox Live valve Kurzanleitung
Fox
Fox 36 Float 160 Bedienungsanleitung
Fox
Fox Live valve Bedienungsanleitung
Fox
Fox 36 Talas 180 Bedienungsanleitung
Fox
Fox FLOAT SL Bedienungsanleitung
Beliebte Fahrradzubehör Handbücher anderer Marken
Sigma
Sigma BC 16.16 Bedienungsanleitung
Playcore
Playcore Dero Setbacks Bedienungsanleitung
VDO Cyclecomputing
VDO Cyclecomputing x3dw Bedienungsanleitung
Cateye
Cateye RAPID X2 Bedienungsanleitung
buratti meccanica
buratti meccanica Clorofilla Trail Bedienungsanleitung
Shimano
Shimano SG-8R20 Betriebsanleitung
