Foxconn 5G + 4G AIO Small Cell Bedienungsanleitung

User Manual

5G + 4G AIO Small Cell

 
1
 
CONTENTS 
Overview.....................................................................................................2 
1 Small cell product dimensions and ports................................................................ 3 
2 Product Specifications......................................................................................... 5 
Quick Setup.................................................................................................7 
Installation guide.........................................................................................7 
1 Hardware installation ........................................................................................... 8 
 ............................................................................................................................ 9 
Key Technology.........................................................................................12 
Industry Standards....................................................................................13 
 

1.Overview

AIO Small cells are low-powered cellular radio access nodes used to increase network

coverage and network capacity in indoor and outdoor wireless communications. This small

cell includes both 5G mmWave and LTE capabilities. It provides high speed data transfer

rates and increased mobility. The AIO small cell can be used to provide both 5G services and

a 4G network. It can be deployed in a commercial network or used in a private network to

service an enterprise.

Figure 1.1- AIO small cell

This small cell successfully complies with 3GPP Release 15 implementation standards. It is

built to operate both indoors and outdoors in the temperature range -40 C to 65 C. It has 2T*2R

4G LTE antennas, 8*8 antenna array with 2-layer for 5G mmWave and 1 GPS antenna port and

is powered by 48V DC power supply. It operates in band 48 for 4G and band n257/n261 for 5G.

It supports 5G mmWave and 2-layer massive MIMO providing a high data throughput greater

than 1Gbps data rate. It supports both licensed band and unlicensed band in 4G LTE.

1.1 Small cell product dimensions and ports

AIO small cell measures 364mm (w) * 335mm (l) * 118mm (h) and weighs 12 Kg.

Figure 1.2 – AIO Small cell product dimensions

Side view

Figure 1.3 – IO ports

Figure 1.4 – DC 48V plug

1.2 Product Specifications

Table 1 Product Specifications

Specification

Description

4G + 5G dual mode small cell

Operating

Frequency

▪26.5 ~ 29.5 GHz (Band n257/n261 for 5G)

▪3550 ~ 3700 MHz (Band 48 for 4G)

TX Power

▪EIRP 50.6 dBm @ 5G mmwave

▪EIRP 24 +- 2 dBm for 4G

RF Bandwidth

▪20MHz @ 4G

▪400MHz @ 5G

Activate users

▪64 ~ 128

Duplex technique

▪TDD

Throughput

▪6.5 / 3.2 Gbps DL/UL

Compute & Storage

Main chip

▪NPU LX2160 + FSM10055 + QTM10028 on 5G

▪FSM9955 + FTR8900 on 4G

Flash/ Memory

▪64GB

Antenna Interface

GPS Antenna

Connector

▪SMA female connector

WAN Interface

Ethernet

▪100/1000/10000 Mbps

Power

Power Input

▪48V DC

Power

Consumption

▪Maximum 150 watts

Antenna

▪64 dual polarized antennas

LTE

▪6 +- 1dBi

GPS

▪1 active antenna with SMA type

Lightning

Protection

▪Earth ground connection with a surge protection cable

Physical Specifications

Mounting

▪Wall and pole mount

Housing Material

▪Aluminum, plastic

Operation

Humidity

▪10% ~ 90%

Operation

Temperature

▪-40 ~ 50 ℃

Net Weight

▪8.5 kg (9.5Kg with bracket)

Dimension

▪364 mm (w) * 335 mm (l) * 118 mm (h)

Reliability

MTBF

▪20 years

2.Quick Setup

Once connected to a power adapter with 48DVC and a 10G Ethernet cable, and the

ethernet link to internet CBSD server and ePC via switch or router and CBSD was for

CBRS LTE function use, and it’s ready to go. The IP addresses are dynamically obtained

through internal DHCP and check the RF LED for service on.

The AIO smallcell support the management system with TR069 for LTE function,

NetCONF/Yang for NR system. It is easy to connect to FNMS (Fii Network Management

System). And it is easy to use the FNMS to control the AIO smallcell with CM/FM/PM and

upgrade firmware.

3.Installation guide

This chapter briefly describes all the steps for the installation of the small cell in terms

of both hardware and software. The small cell shown here is pole mounted.

Figure 3.1 Pole-mounted small cell

3.1 Hardware installation

The small cell can be installed on a pole using a pole mount bracket as shown in Figure 3.2.

Figure 3.2 Pole mounting bracket accessories

•The pole mounting bracket kit consists of a pole mount plate, antenna back plate, pole

clamp plate, hex nuts and hex bolts.

•Step 1: Start by fastening the antenna back plate (A) of the bracket to the back of the

small cell using the Hex nuts (B). This is first done at the top.

•Step 2: Place the bracket firmly on the desired position/height on the pole.

•Step 3: Insert the Hex bolt (F) in the pole mount plate (C). Choose the nut and bracket

based on the size of the pole.

•Step 4: Now place the pole clamp plate (D) firmly behind the pole, align the holes with

the Hex bolt (F) and fasten the hex nuts (E).

•Step 5: First mount the top bracket on to the pole and then repeat the same procedure to

attach the bottom bracket.

•Step 6: The mount can be rotated manually in the vertical plane to point the small cell in

the desired direction as indicated in figure 3.3.

Pole Mount Bracket

Antenna back plate (A)

Pole mount plate (C)

Pole Clamp plate (D)

Hex bolt (F)

Hex nut (E)

Rotate 90

Hex nut (B)

Inhaltsverzeichnis

Andere Foxconn Drahtlosmodul Handbücher

Foxconn

Foxconn T99B226 Bedienungsanleitung

Foxconn

Foxconn J20H076 Bedienungsanleitung

Foxconn

Foxconn J20H086 Bedienungsanleitung

Foxconn

Foxconn J20H090 Bedienungsanleitung

Foxconn

Foxconn RPQN O-RU Installationsanleitung

Foxconn

Foxconn J20H084ac Bedienungsanleitung

Foxconn

Foxconn J20H081 Bedienungsanleitung

Foxconn

Foxconn WBUR56 Bedienungsanleitung

Foxconn

Foxconn T99B226 Bedienungsanleitung

Foxconn

Foxconn WBU063-VZ Bedienungsanleitung

Beliebte Drahtlosmodul Handbücher anderer Marken

Laird

Laird RM024 Bedienungsanleitung

Laird

Laird BT830-SA Kurzanleitung zur Einrichtung

Ebyte

Ebyte E49-400T20S Bedienungsanleitung

Fibocom

Fibocom FM101-NA-20 Montageanleitung

Waldmann

Waldmann EnOcean TALK MODUL G2 Bedienungsanleitung

Smartech

Smartech LBT-1.DO4 Bedienungsanleitung

Cooper Wiring Devices

Cooper Wiring Devices ESPIRE RF RFAPM Bedienungsanleitung

Yuga

Yuga CLM920 Bedienungsanleitung

Waldmann

Waldmann TALK Bluetooth Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions UC864-G Installationshandbuch

Ebyte

Ebyte E07-900M10S Bedienungsanleitung

Quectel

Quectel SC690A Series Beilage

Panasonic

Panasonic INDUSTRY PAN9028 Kurzanleitung zur Einrichtung

Ebyte

Ebyte E70-433NW30S Bedienungsanleitung

LongSung Technology

LongSung Technology U9507E Bedienungsanleitung

Ebyte

Ebyte E49-400M20S4 Bedienungsanleitung

Wistron NeWeb

Wistron NeWeb DNUR-S2 Bedienungsanleitung

RF-Star

RF-Star SimpleLink RF-BM-2652P1 CC2652P Bedienungsanleitung