Francis Searchlights L230 Bedienungsanleitung

User Instruction & Installation Manual

L230 LED 40 Watt Searchlight

Product Reference Number:

A6158 –12/24v DECK

A6159 –12/24v CABIN

Manufacturer’s details: Distributor details:

Manual Part Number: C27604

Issue: 1 1/9/17

Francis Searchlights Ltd

Union Road, Bolton

Lancashire, BL2 2HJ, UK

Tel: +44 (0) 1204 558960

Fax: +44 (0) 1204 558979

http://www.francis.co.uk

E-mail: sales@francis.co.uk

CONTENTS

1 - Introduction

2 - Safety Precautions

3 - Technical Information

4 - Unpacking and Installation Instructions

5 - Electrical Installation

6 - Operating Instructions

7 - Fault Finding

8 - Maintenance and Servicing

9 - Wiring Diagrams & General Assemblies

10 - Spare Parts List

1 - Introduction

It is imperative that this manual is read carefully and understood before

installing your equipment. For your future reference please keep this manual in

a safe place.

Thank you for specifying a product from the Francis Searchlights range. All Francis products are

designed to give complete customer satisfaction and are manufactured to the highest engineering

standards in order to ensure optimum performance and service life.

The Francis LED range combines features proven over many years service in the most hazardous

conditions in both marine and land installations.

In order to prolong the life and performance of your product, we recommend that you only specify

Francis Searchlights spare parts. This will also ensure that any warranties on your equipment will

not be invalidated. Information on spares ordering and parts is provided in this manual.

Should you ever need to contact Francis Searchlights Ltd. regarding your equipment, please quote

the Product Serial Number at all times.

2 - Safety Precautions

The following instructions must be adhered to, in order to ensure a safe working environment and

the safety of the user.

The high luminance of the LED can cause severe damage to the eye if viewed directly.

ALWAYS wear suitable protective goggles when viewing the LED;

Searchlights get hot. Never touch the unit when lit and always allow 15 to 20 minutes for

cooling down after turning the searchlight off;

Never place anything on or cover the searchlight when in use;

Ensure the LED has cooled sufficiently before removal;

Due to the vast range of LED modules available it may appear possible that more powerful

LED’s can be used in the equipment than for which it was designed. Even when the unit will

physically accept a higher wattage LED, this substitution is not recommended and is

dangerous. This action will also void any warranties on the equipment.

3 –Technical Information

This product has been designed to operate in accordance with the product specification.

The L230 LED 40w searchlight has the following features:

All marine grade materials and fixings;

Powder coated finish;

Horizontal rotation 360°;

Vertical movement ±35°;

Instant re-strike. No cooling down time required;

Economical 30,000 hour LED life;

Toughened Opti White front glass;

Luminous flux 4800;

Colour temperature 6000K;

Searchlight Weight 4Kg;

The searchlight also performs to the following optical data:

Supply voltage –12v or 24v;

Range –500 metres at 1 Lux;

Divergence –5°;

Temperature range: -40 to +50

In order that the searchlight operates correctly it is imperative that competent personnel are

responsible for the installation, operation and servicing of this equipment. Failure to adhere to this

advice may cause premature failure or incorrect operation of the searchlight, which may damage

the equipment or cause personal injury.

4 - Unpacking and Installation Instructions

The following instructions should be read and fully understood prior to installing the equipment to

ensure that the correct procedures are followed, and all safety precautions are observed.

Note: If the equipment has been in storage for a considerable amount of time, it is advisable

to conduct a routine maintenance check on all parts before installation.

Safety Precautions

This equipment should not be connected to an electrical supply before being installed. Installation

procedures should be adhered to in order to ensure a safe working environment and reduce the

risk of damage or personal injury.

Preparing the Mounting Position

Mark out and drill 3 off holes Ø6.4mm on a 108mm P.C.D.

A central hole Ø50mm will be required to accept the movement of the control handle. Make sure to

fit the Base-sealing gasket, when in the desired position bolt the searchlight firmly down. On an

uneven surface a suitable sealant maybe required to provide a weatherproof seal.

5 - Electrical Installation

For safety purposes, only competent personnel should perform the electrical installation. All

equipment should be installed to current Electrical Regulations and Standards.

In order to obtain the maximum light output from the searchlight, it is essential that the full

operating voltage of the LED fitted be applied to the LED contacts.

Method of Electrical Connection

1) Disconnect the supply before working on the electrical system;

2) The searchlight must be connected to a fused electrical supply, using suitably sized cable;

3) If the searchlight is located a considerable distance from the supply, provision must be made in

the cable size in order to overcome the voltage drop.

4) Whenever possible cable terminations should be made below deck and with approved terminal

devices;

5) If a spare auxiliary fuse or circuit breaker is not available, one of the correct type and rating

should be fitted and connected to a positive supply. It is advisable to locate a bus bar or main

connection and avoid any direct connection to the supply:

6) When wiring the negative supply, the direct connection to a battery or supply, or metal

hull/object, should be avoided. It is advisable to use a suitable commoning block or connection.

7) For ease of use a single pole switch, of the appropriate rating, should be fitted in a convenient

location. All cable lengths should be kept to a minimum.

6 - Operating Instructions

This equipment is designed for use out of doors, in free air. Never place anything on or cover the

searchlight when in use as this may present a hazard.

The beam of the searchlight cannot be adjusted.

This product should not be used for any purpose other than for which it was designed. Any

modifications to the product should not be undertaken without consulting the manufacturer.

7- Fault Finding

All fault finding must be conducted by a competent person or qualified Electrical Engineer.

Failure of LED to light.

In the event of the LED failing to light the following steps should be taken:

1) Check that the supply is connected to the input of the LED and check all connections as per

the wiring diagram C27603. On operation if the lamp does not light, switch off supply and

check all fuses;

8 - Maintenance and Servicing

In order to prolong the service life and performance of your searchlight, the following maintenance

guidelines are recommended:

Maintenance checks should be conducted before every voyage or at least every three months;

Before checking, disconnect the equipment from the supply;

Visually inspect the condition of the equipment;

Any major or minor structural damage should be rectified immediately in order to reduce

sympathetic wear;

After inspection it may be necessary to clean the inside of the searchlight. The following

procedure should be adhered to:

Remove the front bezel;

Clean the front glass inside and out using a proprietary glass cleaner;

Clean the reflector if required;

It is advisable to check all seals and gaskets for signs of degradation. Renew if necessary;

Upon completing all maintenance requirements, the searchlight should be tested for full

working order (approximately 20 minutes).

If in any doubt as to the correct servicing procedures to adopt please contact your

distributor/agent or the manufacturer who will be able to advise the best course of action for

your product.

Notes for Lamp Fitting/Removal

Ensure all screws are retained carefully in a safe position;

Remove front bezel from searchlight by releasing the three latches;

Remove the three M4 hex head screws that fasten the reflector to the mirror pads.

Remove reflector & unclip lamp leads.

For aid see Diagram C27612. Remove lamp by undoing the 2 screw that hold the plates to

lampholder & then undoing the 4 screws that secure the plates together.

Replace the lamp by reversing the procedure.

It is IMPORTANT the heat dissipation belts on the rear of the lamp are spread to their

maximum (As shown below). Failure to do so will cause damage to the L.E.D

9 - Wiring Diagrams & General Assemblies

Drawing Number Description

A6158/A6159 L230 LED 40w 12/24v Deck/Cabin GA

C27612 Reflector Assembly (Lamp fitting/removal guide)

C27603 Wiring Diagram 12/24v

Inhaltsverzeichnis

Andere Francis Searchlights Scheinwerfer Handbücher

Francis Searchlights

Francis Searchlights A6150 Bedienungsanleitung

Francis Searchlights

Francis Searchlights FH380RC Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7195 VL500 150w 24v LED Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7104 Bedienungsanleitung

Francis Searchlights

Francis Searchlights FX380 Bedienungsanleitung

Francis Searchlights

Francis Searchlights LX480 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7199 Bedienungsanleitung

Francis Searchlights

Francis Searchlights FB230 Bedienungsanleitung

Francis Searchlights

Francis Searchlights FX560D Bedienungsanleitung

Francis Searchlights

Francis Searchlights A6172 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7193 VL500 150w 115/230v LED Bedienungsanleitung

Francis Searchlights

Francis Searchlights FH300 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A6074 Bedienungsanleitung

Francis Searchlights

Francis Searchlights FH380 Bedienungsanleitung

Francis Searchlights

Francis Searchlights L300 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7147 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7164 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7180 VH500 Montageanleitung

Francis Searchlights

Francis Searchlights FX380D Bedienungsanleitung

Francis Searchlights

Francis Searchlights LED300 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A2213 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7186 VX500 100w 24v Xenon Bedienungsanleitung

Francis Searchlights

Francis Searchlights A7123 Bedienungsanleitung

Francis Searchlights

Francis Searchlights A6220 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung