Franke 7612982239618 Bedienungsanleitung

ZMI_001_2030036621-EXOS0027_#SALL_#AQU_#V2.fm / 10.02.22

Installation and operating instructions Montaż i instrukcja obsługi

EA-Nr.: 7612982239618

FAR-Best.-Nr.: 2030036621

EXOS0027

Inhaltsverzeichnis11.fm

...................................................................................... 3

Please refer to the graphics in the German Installation and

Operating Instructions.

...................................................................................... 11

Prosimy przyjąć grafikę z niemieckiej instrukcji montażu i

obsługi.

- 3 -

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

0English

EXOS - A3000open toilet controls for wall-mounted cisterns, 24 V DC.

Please refer to the graphics in the German Installation and Operating Instructions.

0Table of Contents

1. Abbreviations and units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4. Important notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description of product

5. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. ID settings (17010) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

8. Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

9. Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Assembly, function and commissioning

10. Installing the electrical T-distributor . . . . . . . . . . . . . . . . . . . . . . . 7

11. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

12. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

13. Setting the range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

14. Setting the hygiene flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Maintenance

15. Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

16. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

17. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

- 4 -

1. Abbreviations and units

2. Key

Warning!

Failure to observe can result in bodily injury or even death.

Caution!

Failure to observe can result in material damage.

☞Important!

Failure to observe can cause the product to malfunction.

☞Useful information for optimum handling of the product.

3. Warranty

Liability is accepted in accordance with the General Terms and Conditions of

Business and Supply.

Use only original spare parts!

4. Important notes

• Installation, commissioning and maintenance must be performed only by a

qualified expert in accordance with the instructions provided, legal requirements

and recognised engineering standards.

• All technical connection regulations specified by the local water and electricity

supply companies must be observed.

• The power supply should be switched off before any work is carried out.

• We reserve the right to make changes.

RCD Residual current protective device,

Earth leakage circuit breaker

EA-Nr. European article number

FAR-Best.-Nr. Franke Aquarotter order number

Conversion 1 mm = 0.03937 inches

1 inch = 25.4 mm

All length specifications in the graphics are in mm.

- 5 -

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

5. Application

EXOS - A3000 open, non-contact, opto-electronically controlled toilet flush valve for

wall-mounted cisterns, with the option of external control, such as tap settings and

communication via ECC function controller or optional bidirectional remote control.

Electronic module with an additional input for customer-provided sensors

(BUTTONS), maximum distance to electronic module is 5 m.

Control functions:

– Hygienic flushing, 24 hours after last operation and storage of statistical data

– Safety disconnection in the event of continuous activation

Additional functions with ECC function controller (Ethernet):

– Cleaning deactivation

– Concurrence suppression

6. Technical specifications

7. ID settings (17010)

WC (cistern) / IR group sensor / Sanit

FUNCTION:

Pre-flush when the door is closed, after flushing for 5 min. has been completed

pre-flush is locked. Locking time 5 s. at the start of reflection, flushing in the case of

reflection interruption or after the end of reflection. No flushing in the case of refl.

< 5 s. During reflection, triggering is possible via the

disabled button.

SENSORS:

S2: Channel 2 / door contact

S3: Channel 3 / disabled button

S-Bus 1: Channel 3 / IR group sensor

ACTUATORS:

A1: Channel 3 / Sanit cistern motor

Operating voltage: 24 VDC

Power consumption: 4 W

Communication: Ethernet via ECC function controller

Protection class: IP 68

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

- 6 -

SETTINGS:

8. Scope of delivery

9. Dimensions

Range - / 59 cm / 59 cm

TempSensor 1 action -

TempSensor 2 action -

AquaPay -

Flow Time -. / - / -

Overrun time - / - / -

Safety shutdown after -

Reflection alarm after 3600 sec.

Concurrence suppression -

Flow time reduction -

Cleaning deactivation 1 min.

Hygiene flush (dynamic) Interval: 24 h/flow time: 1 sec.

Hygiene flush (fixed) Interval: 0 h/flow time: 1 sec.

Power-on flush Delay: 0 sec / flow time: 1 sec.

TD application time -

TD water saving function -

TD cooling -

Quantity Name

1Motor

1 Electronic module

2 Pressure cap

2 Electrical T-distributor

1 Adapter cable

3 Safety cap

1 Cover plate with frame

1 Installation and operating instructions

- 7 -

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

10. Installing the electrical T-distributor

☞Important!

The components of the electrical T-distributor may only be installed after the power

has been switched off.

☞Recommended system cable see Chapter 17., accessories.

When using cables other than the system cable, pay attention to the different colour

code. The outer diameter must not exceed 7.5 mm.

10.1

Remove the sheathing (a) of the system cable (approx. 40 mm).

10.2

Push the cap nut (c) onto the system cable (b) up to the stop.

☞The various wire guides are marked with numbers 1 to 4.

A: Union nut

B: FAR-Best.-Nr. 2000104272

FAR-Best.-Nr. 2000104274

FAR-Best.-Nr. 2000100801

FAR-Best.-Nr. 2000100852

10.3

Push the wires (d) into the wire guides (e) in accordance with their colours.

10.4

Cut off the projecting wire ends flush, i.e. without protrusions.

10.5

Push the cap nut (c) onto the electrical T-distributor (f) and tighten with the required

torque (1.2 Nm).

Caution!

Note the polarity.

The same wire colour must be in the same wire guide for both union nuts.

☞When tightening the union nut, the electrical contact and tension relief are created

automatically.

Special seals act as protection from dust and water.

1 brown red

2white white

3 blue blue

4 black black

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

- 8 -

11. Assembly

Preparing the electrical connection

☞The power supply should be installed in a separate room outside the wet area and

secured with a residual current device (RCD).

11.1

Install the cistern (a).

11.2

Install the electrical T-distributors (b, c) (see Chapter 10.).

11.3

Attach the motor (d) inside the cistern (see motor instructions).

11.4

Connect the motor (d) to the first electrical T-distributor (b).

11.5

Engage the pressure coil of the cistern (a) on the motor (d).

A: Cable motor (actuator 1)

B: Actuator 2 (optional)

C: Not used

D: Not used

E: Not used

F: Connection for the sensor to be provided by the customer (e.g. door contact)

G: Optical sensor

H: Electrical T-distributor system cable (power)

K: Electronic module

11.6

Connect the cable of the motor (d) to the cable (A) of the electronic module (K).

11.7

Connect the optical sensor via the adapter cable to the electronic module.

Optional

11.8

Connect the sensor to be provided by the customer (e.g. door contact).

11.9

Optional: Connect the second sensor.

e … adapter cable for sensors

f … door contact

g ... yellow

h… brown

11.10

Optional: Connect the third sensor.

e … adapter cable for sensors

k … flush trigger for disabled persons

l… white

m … green (use in combination with Y-sensor distributor 2/3 wire colour "yellow")

11.11

Connect the electronic module (K) to the second electrical T-distributor (c).

11.12

Place the electrical T-distributor (b) into the cistern.

- 9 -

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

Installing the cover plate

11.13

Insert the screws (o) into the tabs (n).

11.14

Turn the screws by 90°.

11.15

Install the frame (p).

11.16

Connect the optical sensor to the electronic module.

11.17

Fit the cover plate (q) and screw it down.

12. Function

12.1

Leave the sensor area.

• The flush system will be activated.

• Flushing will stop automatically.

☞An automatic hygiene flushing function after 24 hours of non-use has been

factory-set.

Function with door contact (optional):

Pre-flushing takes place once when the door is closed.

There is a minimum time interval of 5 minutes between two pre-flushes.

If the door remains locked for more than one minute and the sensor or trigger for the

disabled is not activated during this time, the flush will be automatically activated

when the door is unlocked.

13. Setting the range

The range can be adjusted using an ECC2 function controller via the web

application.

14. Setting the hygiene flush

The hygiene flush can be adjusted with an ECC2 function controller via the web

application.

15. Maintenance and care

The tap must be checked and maintained at regular intervals, depending on the

water quality and in accordance with the local conditions and rules and regulations

applicable at the site.

Use suitable cleaning agents which do not attack the tap in a proper manner and

rinse with water after use. High-pressure cleaners must not be used for cleaning.

ZMI_001_2030036621-EXOS0027_#SEN_#AQU_#V2.fm

- 10 -

16. Troubleshooting

If you cannot rectify a fault or if it is not in the list, please contact our customer

service department!

17. Spare parts

Fault Cause Remedy

Water does not flow – Water supply interrupted ➯Restore it

– Angle valve closed ➯Open it

– Electronics module faulty ➯Replace it

Water flows

continuously

– Motor faulty ➯Replace it

Description Order No.

1 Cover plate complete . . . . . . . . . . . 2030051706

2 Sensor. . . . . . . . . . . . . . . . . . . . . . . 2030041458

3 Motor . . . . . . . . . . . . . . . . . . . . . . . . 2030022899

4 Electronics module M1 . . . . . . . . . . 2030051713

5 Electrical T-distributor . . . . . . . . . . . 2000100853

6 Adapter cable . . . . . . . . . . . . . . . . . 2030062591

Accessories Order No.

ECC-2 function controller

with Ethernet connector and

CAN Bus connector (60 W) . . . . 2000108123

System cable for continuous

use in water,

Halogen-free 100 m . . . . . . . . . . 2000104272

Halogen-free 25 m . . . . . . . . . . . 2000104274

System cable,

Not halogen-free 100 m . . . . . . . 2000100801

Not halogen-free 25 m . . . . . . . . 2000100852

Inhaltsverzeichnis

Sprachen:

Andere Franke Sanitärprodukte Handbücher

Franke

Franke F5 Series Bedienungsanleitung

Franke

Franke F3 Series Bedienungsanleitung

Franke

Franke CMPX551GE Bedienungsanleitung

Franke

Franke F5 F5LM1033 Bedienungsanleitung

Franke

Franke 7612210016837 Bedienungsanleitung

Franke

Franke PROTRONIC-S PRTRS0013 Bedienungsanleitung

Franke

Franke Pescara Semi-Pro PES-SP-304 Bedienungsanleitung

Franke

Franke MARIS FREE Handbuch

Franke

Franke F3SM1002 Bedienungsanleitung

Franke

Franke SIRIUS ZSIRX0040 Bedienungsanleitung

Franke

Franke ZSHOW0008 Bedienungsanleitung

Franke

Franke AQUA741 Bedienungsanleitung

Franke

Franke SIRIUS WB440COP Bedienungsanleitung

Franke

Franke PROTRONIC-S Bedienungsanleitung

Franke

Franke AQUAPINO Bedienungsanleitung

Franke

Franke F5E-Therm F5ET1016 Bedienungsanleitung

Franke

Franke SHHE0004 Bedienungsanleitung

Franke

Franke AQRM905 Bedienungsanleitung

Franke

Franke SIRIUS BS302 Bedienungsanleitung

Franke

Franke CRYSTAL SEMI-PRO FFPD4600 Bedienungsanleitung

Franke

Franke F3EM1010 Bedienungsanleitung

Franke

Franke Steel STL-BR-304 Bedienungsanleitung

Franke

Franke F3SM2004 Bedienungsanleitung

Franke

Franke F5LT1001 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema