FRONIUS 1790FTG0015 Bedienungsanleitung

Power Consumption 500 W

Voltage 220 - 240 V

Amps 2,3 A

No Load Speed 27000 min-1

Sleeve-Ø 43 mm

Tension rod-Ø 6 mm

Grinding Wheel-Ø 50 mm

Weight 2075 g

SPECIAL SAFETY INSTRUCTIONS

 Observe the safety guidelines in this manual!

 Sockets in open air should be equipped with a leak-power security switch. This

is prescribed for your electrical tool. Please apply this when using our equip-

ment.

 When using this machine always wear protective glasses and also gloves,

closed and antislip shoes and an apron.

 Insert the plug into an electrical socket only if the machine is turned off.

 Remove the plug from the electrical socket before doing any work on the ma-

chine.

 Keeptheexawayfromtheareawhereyouareworking.Runtheexaway

from the back of the machine.

 After disconnecting the spindle is still turning, lay down the tool only after com-

plete standstill.

 Do not reach into the danger zone of machinery that is turned on.

 Only use tools with an rpm at least as high as the highest idle rpm of the ma-

chine.

 Inspect the grinding wheel before use. The wheel must be perfectly mounted in

order to turn freely. Test the wheel for at least 30 seconds before use. Do not

use wheels that are damaged, asymmetrical, or that vibrate.

 Grinding metals originate sparks. Please take care nobody gets hurt. Do to

rehaardnocombustiblematerialsshouldbeincloserange.Donotusfume

extractors.

 Please hold the engine in such a way that sparks and grinding dust are blow

away from your body.

 Tighten the tension nut before each use of the machine.

 Underextremeelectromagneticinterferencefromoutside,mayoccurtempo-

rary alternations in rotations.

 Keep always the vent-holes clean.

BRIEF DESCRIPTION

1. Grinding Head :

2. Motor unit :

BRIEF DESCRIPTION

3. Power On/Off :

Power off: Push the on/off switch

back. The switch will automatically

return in the 0 position.

Power on : Push the on/off switch

forward. Press the front of the switch

to lock it in position.

Electrical Connection :

Connect only to single-phase alternating current and only to the voltage stated on

thespecicationlabel.TheFRONIUSTIGGRINDERMOBILEisinsulatedaccor-

dingtoDIN57740/VDE0740(EEC20andcanbeconnectedtoungrounded

electricalsockets.RadiointerferencecomplieswithEuropeanNormEN55014.

4. Vacuum Removal of Dust :

 Loosenandthencompletelyremovethethreehexagonalcountersunk

  screwswitha4mmhexagonalkey

 Remove the cover

 Use the supplied

rotating socket and

connect to the vacuum

system.

We recommend this procedure as a safety measure to minimise contact with the

tungsten dust that results from the grinding process.

5. Angle Iron :

 The angle iron must be mounted

so that the machine

- can be fastened in a vice

- can be fastened by means

of a screw clamp

6. Optional Grinding Head :

 Asecondhead(colouredredisavailablefortheFRONIUSTIGGRINDER

  MOBILEforelectrodeswithdiametersof1.0/4.0/4.8/6.0millimetres.

TECHNICAL DATA

  TIGGRINDERMOBILE

- 2 -

Operating Instructions

TUNGSTEN ELECTRODE GRINDER

TIG GRINDER MOBILE

Spindle + Nut

Wheel take-off shaft

Coated side

of wheel

Wheel

Washer

Nut

GENERAL SAFETY INSTRUCTIONS

USEFUL TIPS

SYMBOLS

Read the instructions before

using this equipment.

Protect your eyes ! Wear safety goggles when using this equip-

ment.

Removal of used equipment, this tool can be disposed, free of

charge , at indicated local agencies.

ThisequipmenthasbeentestedaccordingtoEN60745,98/37/

EG(28.12.09,2006/42/EG(29.12.09,2004/108/EG.

Safety class II, safety insulation

7. How to Use :

 Makeadjustmentsfortheangleofthepoint(indegrees

and the electrode diameter

- Loosen the central screw on the head

- Set the degree and the electrode

diameter by turning the head

- Tighten the central screw

The number of degrees equals the angle

of the point on the sharpened electrode:

 Guide the tungsten electrode through the opening that coincides with its

diameter;

 TurnontheTIGGRINDERMOBILE

 Carefully press the tungsten electrode onto the revolving disc, while at the

same time rotating it with light pressure;

 Continue to rotate the electrode as it is removed from the disc until there is

no longer any contact;

 Inspect the results and, if necessary, repeat the process;

 The multi-functional cover with integrated opening slide makes it possible to

surface grind electrodes that have welding deposits due to the welding

process. In addition, ground electrodes can be optimised for aluminium

welding by being given a truncate cone.

 3stepsadjustmentfortripleuseofthegrindingdiscbyturningthegrindingin

position 1,2 or 3.

Warning ! Do not sharpen bent or burnt electrodes. Remove any drops on the point

of the electrode before it is sharpened. Use the electrode holder for short electrodes.

BRIEF DESCRIPTION

CHANGING THE GRINDING WHEEL

Remove the plug from the electrical socket before doing any maintenance on

this machine !

 LoosentheM6screwsandremovethemcompletely

 Removeheadshowingtheangleadjustment

 Loosen the stud bolts on the sides

 Remove the house

 Loosen and unscrew the tension nut

 Change the wheel

 Warning ! Ensure that the wheel is mounted correctly

 Replace the washer

 Screw the nut back on and tighten it

CHANGING THE WHEEL MOUNT

Remove the plug from the electrical socket before doing any maintenance on

this machine !

 Position spanner SW 13 on the spindle

 PositionspannerS19onthenut

 Loosen the nut

 Replace the wheel mount

 Tighten the nut

Followthesame

procedure to change

thespringcollet,except

that the nut must be completely

unscrewed in order for the spring to be changed.

Theseproceduresmustbefollowedexactlyastheyareexplainedandillustrated.

Remove the plug from the electrical socket before doing any maintenance on

this machine !

The tension rod must have the same diameter

as the take-off shaft; otherwise the tension

rod will be damaged.

Fitthetake-offshaftinto

the tension rod.

The take-off shaft must rest

on the nut.

Very important !!!

Position spanner SW 13

on the spindle and tighten

thenutwithS19.

Place the wheel on

thetake-offshaft.Ensure

that it is properly mounted

and not crooked. Put on the

washer, screw on the nut and

tighten with spanner SW 10.

PAYATTENTION.Pleaseobservethesesafetyguideli-

nes.Notfollowingthemcancauseelectricalshock,re

and/orheavyinjuiries.Thefollowingconceptelectrical

toolconcernstoolswithelectricalexasalsotools

with build-in batteries.

PLEASEGUARDTHESEINSTRUCTIONSCARE-

FULLY

1. Working place.

a Keepittidyandclean.Disorderandlowlightcan

occur accidents.

b Dontusethetoolinandangerousexplosiveen-

vironment,whereammableproducts,gasesand

dustarepresent.Electricaltoolsproducesparkles,

that can ignite the dust or gases.

c Keepchildrenandotherpersonsawaywhenusing

anelectricaltool.ithanunexpecteddeviationone

can loose control on the tool.

2.Electrical safety.

a Theplugandsocketmustbeappropriate.Dont

changethepluganddontuseanadaptertogether

with an earthed tool. Unchanged plug and socket

decrease the risk of electrical shocks.

b avoidbodycontactwithearthedsurfaces,suchas

pipes,radiators,stoves and refrigerators. There is a

high risk of electrical shock if your body is earthed..

c Protectthetoolfromrainandhumidity.ater

penetration can cause electrical shock.

d Dontusetheexasahandletocarrythetool,for

hanging it on the wall or to pull out the plug from

thesocket.Keeptheexfarfromheat,oil,sharp

edges or revolving parts of equipment. Damaged

ortwistedexesincreasestheriskofelectrical

shocks.

e henworkingoutsideonlyuseextensionexes

that has been approved for outdoor use. Doing so

one decreases the risk of electrical shock.

3. Safety of people.

a Beattentive,lookwhatyouaredoing,andbe

ingenious when working with an electrical tool.

Dontusethetoolwhenyouaretiredorunderthe

inuenceofdrugs,alcoholormedicine.Oneshort

momentofinattentioncanleadtosevereinjuries.

b Alwayswearpersonalprotectionequipment,such

as safety goggles,anti slip shoes,safety helmet

orearmufes,dependingonthetypeofelectrical

toolsinuse.Doingsoreducestherisksofinjuries.

c Preventtheequipmentfromstartingunexpectedly.

Makesurethattheswitchisonoffbeforeplug-

ging in. Never carry equipment that is connected

withyourngeronthepowerswitch.

The best results will be obtained by applying light pressure to the electrode while

at the same time rotating it on the disc. Remove the electrode before turning off

the grinder.

Using too much pressure while grinding will damage the grinder and require more

grinding discs; performance will suffer.

Warning : Always keep the air-intake vents clean.

Accessories :OnlyuseFRONIUSaccessoriesandspareparts.

Spare parts :

Order No.

Grinding wheel 42,0411,0012

PleaserefertotheFRONIUSProductCatalogueforotherreplacementparts,or

ask your dealer.

d Checkbeforestartingthatthekeyandadjustment

tools have been removed.

e Dontoverestimateyourself.Makesuretohavea

secure posture and balance. Doing so ,you are in

better position to control the tool.

f earthecorrectclothing.Dontwearlooseclothing

orjewellery.Keeplonghair,clothesandgloves

away from revolving parts.

g Ifmountingfume-andordust-extractorsmake

sure that they are connected and used the right

way. Doing so is avoiding dust-problems.

4. Carefully handling and use of electrical tools.

a Dontoverloadthetool.Foreveryjobusethe

appropriate electrical tool. Doing so you will obtain

a better and safer result .

b Dontuseanelectricaltoolwithadefectswitch.A

toolwithadefectswitchcannotbeswitchedoff

oron,isdangerousandmustberepaired.

c Pullouttheplugfromthesocketbeforeyouwish

tochangetheadjustments,changesomeparts

or putting away the tool. These measures prevent

unexpectedstartofthetool.

d Keepunemployedelectricaltoolsoutofreachof

childrenDontleavethistoolinhandsofpeoplenot

usedtohandleitorhaventnotreadtheseinstruc-

tions.Electricaltoolsaredangerouswhenusedby

inexperiencedpersons.

e Takecareofyourtool.Pleasecontrolifeverytur-

ningpartcanworkfreelyandisntblocked,orthat

some parts are broken or damaged. Let the tool

berepairedbeforeuse.Manyaccidentsaredueto

badly maintenance of electrical tools.

f Keepcuttingtoolscleanandsharp.Doingsoone

getsabettergripandeasierjobdone.

g Onlyuseelectricaltools,sparesaso,conformthese

instructions for this tool .Take also into conside-

rationtheenvironmentandthejobthathastobe

done. The use of electrical tools for inadequate

jobscanleadtodangeroussituations.

5. Service.

Haveyourtoolservicedbyqualiedpersonaland

repaired only with original spare parts. Than you will be

sure that the safety of the tool is guaranteed.

- 3 -

Inhaltsverzeichnis

Andere FRONIUS Schleifer Handbücher

FRONIUS

FRONIUS TIG GRINDER MOBILE Bedienungsanleitung

Beliebte Schleifer Handbücher anderer Marken

Parkside

Parkside PWS 230 C3 Bedienungsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Technisches Handbuch

PTA

PTA P1322 Bedienungsanleitung

Crown

Crown CT13313 Bedienungsanleitung

Parkside

Parkside 280250 Bedienungsanleitung

Climax

Climax VM2150 Series Bedienungsanleitung

Jet

Jet JPSG-618M1 Service-Handbuch

Makita

Makita GA4030 Bedienungsanleitung

DeWalt

DeWalt DWEN202 Bedienungsanleitung

Grizzly

Grizzly G2790 Bedienungsanleitung

Fein

Fein MSf843-1a Bedienungsanleitung

Bosch

Bosch GWS 14,4 V PROFESSIONAL Bedienungsanleitung

RAMSET

RAMSET CBAGR18 Bedienungsanleitung

Bosch

Bosch 8-115 Z Bedienungsanleitung

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Bedienungsanleitung

MW TOOLS

MW TOOLS ME15W Bedienungsanleitung

Caravaggi

Caravaggi SP 20 Betriebsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Technisches Handbuch

FRO­NIUS 1790FTG0015 Bedienungsanleitung

Beliebte Schleifer Handbücher anderer Marken

FRONIUS 1790FTG0015 Bedienungsanleitung