FS IES3110-8TF Bedienungsanleitung

L2+ MANAGED INDUSTRIAL SWITCH

L2+ MANAGED INDUSTRIELLER SWITCH

SWITCH INDUSTRIEL MANAGEABLE L2+

Quick Start Guide V1.0

Quick-Start Anleitung

Guide de Démarrage Rapide

IES3110-8TF Switch

P1 FAULT

RESET

1 2

R.O.RING

1G/2.5G Link/Act 1G/2.5G

SFP

Link/Act

IES3110-8TF

Link

Act

1000

Act

Link

Introduction

Accessories

IES3110-8TF

Thank you for choosing IES3110-8TF Managed Switch. This guide is designed to familiarize you with

the layout of the switch and describes how to deploy the switch in your network.

Mounting Bracket x2 M3 Screw x4

NOTE: IES3110-8TF switch has dust plugs delivered with it. Keep the dust plugs properly

and use them to protect idle ports.

P1 FAULT

RESET

1 2

R.O.RING

1G/2.5G Link/Act 1G/2.5G

SFP

Link/Act

IES3110-8TF

Link

Act

1000

ActLink

2x 100/1000/2500BASE-X SFP Ports

Max. fault loading: 24V,1A

DC Input: 12-48V,1.25A max.

AC Input: 24V~,0.7A max.

23456

V1+ V1

PWR1

V2+ V2

PWR2

Fault

P1 FAULT

RESET

1 2

R.O.RING

1G/2.5G Link/Act 1G/2.5G

SFP

Link/Act

IES3110-8TF

Link

Act

1000

ActLink

Front Panel Ports

Upper Panel

Hardware Overview

8x 10/100/1000BASE-T Ports

Ports Description

10/100/1000BASE-T ports for Ethernet connection

SFP ports for 100M/1G/2.5G connection

RJ45

SFP

Grounding Point

Terminal Block Connector

Rear Panel

Front Panel LEDs

DIN-rail Mounting Kit

P1 FAULT

RESET

1 2

R.O.RING

1G/2.5G Link/Act 1G/2.5G

SFP

Link/Act

IES3110-8TF

Link

Act

1000

ActLink

SFP

RJ45

SYS

Installation Requirements

NOTE: It is recommended to use Internet Explorer 8.0 or above to access the switch. If the

web interface of the Industrial Managed Switch is not accessible, please turn oﬀ the

anti-virus software or ﬁrewall and then try it again.

Indicates the Switch has power.

LEDs DescriptionStatus

Green

Light

Blink

Orange

Light

Oﬀ

Green

Indicates power failure.

Indicates that the ERPS Ring has been created successfully.

Indicates that Switch has been enabled to Ring Owner.

SYSTEM

RJ45

Fault

Ring

R.O.

Indicates the link through that port is successfully

established.

Indicates that the Switch is actively sending or receiving

data over that port.

Indicates that the port is successfully connecting to the

network at 1000Mbps.

Indicates that the port is successfully connecting to the

network at 10Mbps or 100Mbps.

LINK/ACT

1000

Green

Light

Blink

Orange

Light

Oﬀ

SFP

Indicates the link through that port is successfully

established.

Indicates that the Switch is actively sending or receiving

data over that port.

Indicates that the port is successfully connecting to the

network at 1000Mbps.

Indicates that the port is successfully connecting to the

network at 100Mbps.

LINK/ACT

1000

Before you begin the installation, make sure that you have the following:

Workstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS X or later, Linux, UNIX, or

other platforms are compatible with TCP/IP protocols.

Workstations are installed with Ethernet NIC (Network Interface Card).

Ethernet Port Connection

Network cables -- Use standard network (UTP) cables with RJ45 connectors.

The above PC is installed with Web browser.

1. Position the unit in front of the DIN-Rail and hook the mount bracket over the top of the rail.

2. Rotate the switch downward towards the rail to lock it into place. You will know it is secure when

you hear the click.

3. To remove the unit, pull down to clear the bottom of the DIN-Rail and rotate away from the rail.

Mounting the Switch

Screw on the mounting bracket on the switch with M3 screws.

DIN-Rail Mounting

Wall Mounting

Mounting the unit Releasing the unit

Max. fault loading: 24V,1A

DC Input: 12-48V,1.25A max.

AC Input: 24V~,0.7A max.

23456

V1+ V1

PWR1

V2+ V2

PWR2

Fault

Max. fault loading: 24V,1A

DC Input:12-48V,1.25A max.

AC Input:24V~,0.7A max.

23456

V1+ V1

PWR1

V2+ V2

PWR2

Fault

123456

V1+ V1

PWR1

PWR2

Fault

The Upper Panel of the switch indicates an AC/DC inlet power socket and consists of one terminal

block connector within 6 contacts. Please follow the steps below to insert the power wire.

1. Insert positive/negative AC or DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5

and 6 for Power 2.

Connecting the Power

NOTE: This product is intended to be mounted to a well-grounded mounting surface such

as a metal panel.

Grounding and wire routing help limit the eﬀects of noise due to electromagnetic interference (EMI).

Run the ground connection from the ground screw to the grounding surface prior to connecting

devices.

Grounding the Switch

DC Input: 12-48V ,1.25A max.

AC Input: 24V~,0.7A max.

23456

V1+ V1

PWR1

V2+ V2

PWR2

Fault

12-48VDC,24VAC

V1+ V1- V2+ V2-

PWR1 PWR2

123456

NOTE: The wire gauge for the terminal block should be in the range from 12 to 24 AWG.

Pin 2 / 6

Positive (+) Pin Negative (-) Pin

Pin 1 / 5

2. Tighten the wire-clamp screws for preventing the wires from loosening.

Live line/Positive

Null line/Negative

Requiring good ground connection

NameNo. Description

V1+, V2+

V1-, V2-

P1 FAULT

RESET

1 2

R.O.RING

1G/2.5G Link/Act 1G/2.5G

SFP

Link/Act

IES3110-8TF

Link

Act

1000

Act

Link

P1 FAULT

RESET

1 2

R.O.RING

1G/2.5G Link/Act 1G/2.5G

SFP

Link/Act

IES3110-8TF

Link

Act

1000

Act

Link

1. Plug the compatible SFP transceiver into the SFP port.

2. Connect a ﬁber optic cable to the ﬁber transceiver. Then connect the other end of the cable to

another ﬁber device.

Connecting the SFP Ports

1. Connect an Ethernet cable to the RJ45 port of a camera, outdoor AP, computer or other network

device.

2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.

Connecting the RJ45 Ports

Step 1: Connect the computer to any RJ45 port of the switch using the network cable.

Step 2: Set the IP address of the computer to 192.168.1.x ("x" is any number from 2 to 255).

Step 3: Open a web browser, enter the default IP address of the switch 192.168.1.1, and enter the

default username and password, admin/admin.

Step 4: Click Login to display the web-based conﬁguration page.

100M/1G/2.5G Port is not Working

1. Ensure the optical module and cable have no problem.

2. Check if the conﬁguration at both ends of the communication device is auto or forced rate.

Connecting the Switch Remotely Unsuccessfully

1. Test network connectivity through ping.

2. If the network is reachable, try restarting the switch.

3. Check if the corresponding service is enabled.

The Port is not Working, the LED Indicator is Oﬀ

1. Ensure the switch ports are in the no shutdown state.

2. Check if the switch can read the DDM information.

3. Check if the port speed setting is correct.

4. Try looping the switch cable.

Conﬁguring the Switch

Troubleshooting

Conﬁguring the Switch Using the Web-based Interface

RJ45 port is not in connectivity or it is erroneous in receiving/

transmitting frames

1. Replace the twisted pair cable.

2. Check that the port conﬁguration has the common working mode with the connected switch.

Inhaltsverzeichnis

Sprachen:

Andere FS Schalten Handbücher

FS S3910 Series Bedienungsanleitung

FS S3700-24T4F Bedienungsanleitung

FS S5500-48T8SP Bedienungsanleitung

FS S5900-24S4T2Q Kurzanleitung

FS S3410 Series Bedienungsanleitung

FS S3700-24T4F Bedienungsanleitung

FS S3150-8T2FP Bedienungsanleitung

FS S1900-24T Bedienungsanleitung

FS S3700-24T4F Bedienungsanleitung

FS S3150-8T2FP Bedienungsanleitung

FS S5850-24S2C-DC Bedienungsanleitung

FS S1900-8TP Bedienungsanleitung

FS S5860-48SC Betriebsanleitung

FS N9510-64D Bedienungsanleitung

FS S5800-48F4SR-DC Bedienungsanleitung

FS Fiberstore S8050-20Q4C Bedienungsanleitung

FS S5850-24S2Q Bedienungsanleitung

FS S5900-24S4T2Q Bedienungsanleitung

FS S5800 Series Bedienungsanleitung

FS IES5100-24FS Bedienungsanleitung

FS S1900-5T Bedienungsanleitung

FS S3410 Series Betriebsanleitung

FS S3910-24TF Betriebsanleitung

FS TAP Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung