FS S3700-24T4F Bedienungsanleitung
COMMUTATEUR D'ACCÈS FULL-GIGABIT
S3700-24T4F Switch
FULLGIGABIT ACCESS SWITCH
V3.1
Quick Start Guide
Quick-Start Anleitung
Guide de Démarrage Rapide
EN
Introduction
Thank you for choosing FS S3700-24T4F Full-gigabit Access Switch. This guide is designed to familiarize
you with the layout of the switch and describes how to deploy the switch in your network.
S3700-24T4F
Accessories
Power Cord x 1 Console Cable x 1 Mounting Bracket x 2
Rubber Pad x 4 M3 Screw x 8
1
Grounding Cable x 1
EN
Hardware Overview
Front Panel Ports
Front Panel Button
RJ45
RESET
Console SFP
Ports Description
RJ45 10/100/1000BASE-T ports for Ethernet connection
Hot swappable SFP ports for 1G fiber connection
An RJ45 console port for serial management
SFP
Console
Reset Keep the device powered on, press the button "RESET" for 6 seconds,
and the system will return to the default setting.
Button Description
2
EN
Site Environment
Front Panel LEDs
Back Panel
Grounding Point
Power Supply
SYS
SFPPWR RJ45
Do not operate it in an area that exceeds an ambient temperature of 50°C.
The installation site must be well ventilated. Ensure that there is adequate air flow around the
switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
LEDs Status Description
PWR Green Switch is powered on.
SYS
Orange 10/100M connection.
1000M connection.Green
Off
Green
Off No signal transmission.
1000M connection.
No signal transmission.
Blinking Green System is working properly.
RJ45
SFP
3
EN
Installing
Desk Mounting
Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with eight M3 screws.
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
4
EN
Grounding the Switch
2. Attach the switch to the rack using four M6 screws and cage nuts.
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washers
and screws.
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
5
EN
Connecting to the power
Connecting to the RJ45 Ports
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
1. Connect an Ethernet cable to the RJ45 port of a computer, printer, network storage, or other network
devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
WARNING: Do not install power cables while the power is on.
6
EN
Connecting to the SFP Ports
Connecting to the Console Port
1. Plug the compatible SFP transceiver into the SFP port.
2. Connect a fiber optic cable to the fiber transceivers. Then connect the other end of the cable to
another fiber device.
1. Connect the DB9 female connector of the console cable to RS-232 serial port on the computer.
2. Insert the RJ45 connector into the RJ45 console port on the front of the switch.
7
EN
Configuring the Switch
Troubleshooting
Configuring the Switch Using the Web-based lnterface
Configuring the Switch Using the Console Port
Power LED Working Abnormally
Step 1: Connect your computer to any Ethernet port of the switch using the network cable.
Step 2: Set up the lP configuration on your computer.The lP address of your computer should be set in
the same subnet addresses of the switch.The lP address is 192.168.1.x("x" is any number from
2 to 254).
Step 3: Open a web browser window.Enter the default lP address of the switch http://192.168.1.1 in the
address bar and press Enter.
Step 4: When the login page appears choose the language that you prefer and enter the username and
password.
The default username is admin.The default password is admin.
Step 5: Click Sign in to display the web-based configuration page.
Step 1:Connect a computer to the switch's console port using the supplied console cable.
Step 2:Start the terminal simulation software such as HyperTerminal on the computer.
Step 3:Configure the terminal simulation with the following parameters:
115200 bits per second
8 data bits
no parity
1 stop bit
no flow control
Step 4:Enter the username and password.The default username is admin.The default password is
admin.
1. Check the power cable connections at the switch and the power source.
2. Make sure the power cord used matches the voltage and frequency of your local power.
8
EN
HyperTerminal Displaying Abnormally
Accessing the Web-based Configuration Page Unsuccessfully
1. Make sure the power supply is normal and the console cable is properly connected.
2. Check if the console cable is the right type.
3. Check if the control cable driver is properly installed on the computer.
4. Ensure the parameters of the HyperTerminal are correct.
1. Check every port LED on the switch and make sure the Ethernet cable is connected properly.
2. Try another port on the switch and make sure the Ethernet cable is suitable and works normally.
3. Power off the switch. After a while, power it on again.
4. Make sure the IP address of your PC is set within the subnet of the switch.
5. If you still cannot access the configuration page, please restore the switch to its factory defaults.
Then the IP address of your PC should be set as 192.168.1.x ("x" is any number from 2 to 254) and
Subnet Mask as 255.255.255.0.
Online Resources
Download
Help Center
Contact Us
https://www.fs.com/products_support.html
https://www.fs.com/service/fs_support.html
https://www.fs.com/contact _us.html
Product Warranty
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a
free return within 30 Days from the day you receive your goods. This excludes any custom made
items or tailored solutions.
Warranty: FS S3700-24T4F Switch enjoys 4 years limited warranty againist defect in
materials or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_ return_ policy.html
4
9
Andere Handbücher für S3700-24T4F
12
Inhaltsverzeichnis
Sprachen:
Andere FS Schalten Handbücher
FS
FS S1900-16TP Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S3900 Series Bedienungsanleitung
FS
FS S5850-24XMG Bedienungsanleitung
FS
FS IES3110-8TF Bedienungsanleitung
FS
FS NC8400 Series Bedienungsanleitung
FS
FS S3150-8T2FP Bedienungsanleitung
FS
FS S5860 Series Betriebsanleitung
FS
FS S5800-48F4S Bedienungsanleitung
FS
FS S3270 Series Betriebsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS N5860 Series Bedienungsanleitung
FS
FS S5810 Series Betriebsanleitung
FS
FS S5850-24S2C-DC Bedienungsanleitung
FS
FS S3700-24T4F Bedienungsanleitung
FS
FS S5300-12S Bedienungsanleitung
FS
FS N Series Bedienungsanleitung
FS
FS S3260-8T2FP Bedienungsanleitung
FS
FS S5850-24S2Q-DC Bedienungsanleitung
FS
FS S2800S Series Bedienungsanleitung
