FujiFilm Frontier-S DX100 Bedienungsanleitung

Revision 2.04 - V4.3 Driver- 11/23/16

Frontier-S DX100 printer with

DarkRoom Pro Software

Windows V4 Driver

Version 9.1.1978 Basic Driver

and

DarkRoom 9.20.2232 or higher for Advanced Driver integration

Installation Guide

Revision 2.04 - V4.3 Driver- 11/23/16 2

This page is

intentionally left

blan

Revision 2.04 - V4.3 Driver- 11/23/16 3

Table of Contents

Introduction 4

General System Information and Note on USB Port Installation 5

System Topology 6

Software, hardware and documents needed for this installation

Setting up the Frontier-S DX100 Printer 7

Installing the DarkRoom Pro software on the Client PC 8

Setting up the Frontier-S DX100 printer(s) on the DarkRoom PC 12

Setup and use of DarkRoom Pro 23

Appendix: Operation Notes; Color Management with Windows

Driver and DarkRoom 26

Revision 2.04 - V4.3 Driver- 11/23/16 4

Introduction

This guide will provide you with the necessary steps that need to be taken to install the Frontier-S

DX100 with DarkRoom Pro software using Version 9.1.1978 and Version 9.2 and higher.

Please Note: To take full advantage of the Fujifilm DX100 V 4 Driver with DarkRoom Pro

you must have DarkRoom Pro Version 9.2.2232 or higher. This will enable automatic set up of

the “Fujifilm DX100 EX” printer.

Set up in Versions 9.1.1978 or lower can be accomplished by use of the Windows Driver Printer

Set Up in DarkRoom Pro. In this basic option you will need to refer to your DX100 Operators

Manual for creation of custom page sizes.

To take full advantage of advanced integration of DX100 it is necessary to upgrade to the latest

version of DarkRoom Pro Version 9.2.2232 and higher uses direct drivers to communicate with

the DX100 printer. Benefits from this upgrade are advanced set up options in the driver as well

as automated page size selection and more efficient production.

Darkroom Pro software is to be installed on a client supplied PC (System PC) that meets the

following specifications:

Windows 7 Service Pack 1, 32 or 64 Bit

Windows 10 Pro 32 or 64 Bit

It is important that DarkRoom Pro software is installed on a computer that has the ability to

accommodate the workload of both software and the video graphics requirements of an imaging

workstation.

The DX100 Printer(s) connect directly to the DarkRoom Pro Workstation/PC via USB cable(s). A

total of up to *6 printers has been tested and is supported.

Revision 2.04 - V4.3 Driver- 11/23/16 5

General System Information

Note on Printer USB Port Installation: The Frontier-S DX100 printer connects to DarkRoom

Pro computer as USB connection one computer to multiple printers. Note location, port number

and printer number when installing. If a printer is disconnected or replaced connect only to the

port that the printer was originally installed on. When swapping or replacing a printer, refer to

the DX100_Printer_Driver_Operation_Guide_EN.pdf Fourth Edition and use of Frontier-S DX100

Maintenance Tool for correct registration of the printer.

See Topology Illustration on Page 7.

Minimum requirements for the DarkRoom PC computer (Client PC) are that it will need to support

the Operating System installed with RAM, (4Gb) Hard Drive Space (200 Gb). The system must

be capable of handling advanced image processing applications.

Operating Systems supported are Windows XP Pro with SP 3, OR Windows 7 Service Pack 1 ,

32/64 Bit, Windows 10 Pro 32/64 Bit.

Before you proceed with the installation it is important that you review and understand the

installation guide. Be familiar with the installation steps before beginning the installation.

Revision 2.04 - V4.3 Driver- 11/23/16 6

System Topology

The illustration below shows a Host PC which meets minimum configurations outlined in the

DX100 Installation Manual, Frontier-S Printer Driver Operation Guide EN.pdf Fourth

Edition. DarkRoom Pro is installed on the Client PC. The DX100 Printer is connected to the Host

PC via USB.

DX100 Connected via USB to the DarkRoom Pro Computer

Revision 2.04 - V4.3 Driver- 11/23/16 7

Software, hardware and documents needed for this installation:

Customer provided Computer which matches minimum specifications outlined in

General Information.

Fujifilm Frontier-S DX100 Printer(s)

DarkRoom Pro software and License/USB Dongle, supplied by FUJIFILM NAC

Marketing/Sales, or purchased directly from DarkRoom Software LLC

DarkRoom Pro Installation Guide and Quick Start Guide, supplied with the DarkRoom

software package

DX100 Windows Driver Software v 4 or higher, supplied with the Printer

Frontier-S Printer Driver Operation Guide EN.pdf Fourth Edition supplied with the

Printer

DarkRoom Pro installation Disk Version 9.10.1978, 9.2 or higher is preferred.

Setting up the DX100 Printer

Installation Preparation and unpacking the printer

Unpack and install the Frontier-S DX100 Printer as described in the Frontier-S DX100

Installation Manual supplied with the printer.

Printer Installation

Continue with the Printer installation of the Windows Driver following directions in

DX100_Printer_Driver_Operation_Guide_EN.pdf Fourth Edition - Pages 4 through 5.

Installation and Settings: Frontier-S DX100 Printer Driver Operation Guide EN.pdf

Fourth Edition pages 9 through 12

Review

Review and follow the instructions for the use of the Frontier-S DX100 Printer Driver

Operation Guide EN.pdf Fourth Edition Pages 12 through 50.

Revision 2.04 - V4.3 Driver- 11/23/16 8

Installing DarkRoom Pro software on the System PC

The Frontier-S DX100 S should be set up following instructions found in General Information and

Frontier-S Printer Driver Operation Guide EN.pdf Fourth Edition

To Install DarkRoom Pro on your host computer:

1. Insert the DarkRoom Pro installation disk into the DVD drive

2. If the Dvd does not automatically run

3. Click on Start > Run… > Browse..

4. Select SetupDRPRoxxxx.exe

5. Click OK to run the installer

6. Click OK

7. The Install Shield Wizard will start

Revision 2.04 - V4.3 Driver- 11/23/16

8. When the DarkRoom Professional installer starts, Click Next

9. Select the Radio button to “Accept the terms in the license agreement” and Click Next

Revision 2.04 - V4.3 Driver- 11/23/16

10. Click Next

11. Click Install

Andere Handbücher für Frontier-S DX100

Inhaltsverzeichnis

Andere FujiFilm Drucker Handbücher

FujiFilm

FujiFilm Printpix NC-400D Bedienungsanleitung

FujiFilm

FujiFilm MP-70 Bedienungsanleitung

FujiFilm

FujiFilm B9136 Bedienungsanleitung

FujiFilm

FujiFilm ASK-300 Bedienungsanleitung

FujiFilm

FujiFilm Frontier 570 Montageanleitung

FujiFilm

FujiFilm FM-DP L Bedienungsanleitung

FujiFilm

FujiFilm instax mini Link Bedienungsanleitung

FujiFilm

FujiFilm B9136 Bedienungsanleitung

FujiFilm

FujiFilm Apeos 7580 Bedienungsanleitung

FujiFilm

FujiFilm Xerox Phaser 6270 Bedienungsanleitung

FujiFilm

FujiFilm ASK-300 Bedienungsanleitung

FujiFilm

FujiFilm 3000 Bedienungsanleitung

FujiFilm

FujiFilm Apeos 5570 Bedienungsanleitung

FujiFilm

FujiFilm ASK-2500 Bedienungsanleitung

FujiFilm

FujiFilm FLA-8000 Bedienungsanleitung

FujiFilm

FujiFilm DryPix 7000 Bedienungsanleitung

FujiFilm

FujiFilm PICTROGRAPHY 4500N Bedienungsanleitung

FujiFilm

FujiFilm Apeos 4570 Bedienungsanleitung

FujiFilm

FujiFilm instax square Link Bedienungsanleitung

FujiFilm

FujiFilm ASK-300 Bedienungsanleitung

FujiFilm

FujiFilm ApeosPrint C325 dw Bedienungsanleitung

FujiFilm

FujiFilm ApeosPro C810 Bedienungsanleitung

FujiFilm

FujiFilm ApeosPort V C7785 Bedienungsanleitung

FujiFilm

FujiFilm ApeosPort-VII 4021 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung