Fujitsu Flash-64P-M01 Bedienungsanleitung

Flash-64P-M01/M09

Page 1

Flash-64P-M01/M09

Evaluation Board

Documentation

Fujitsu Mikroelektronik GmbH

Rev. 1.1

Flash-64P-M01/M09

Page 2

History

Revision Date Comment

V1.0 10.05.99 New Document

V1.1 09.07.99 History Table added on page 2, addendum 1

included in chapter 1.4.2

Flash-64P-M01/M09

Page 3

Warranty and Disclaimer

To the maximum extent permitted by applicable law, Fujitsu Mikroelektronik

GmbH restricts its warranties and its liability for the Product [Flash-64P-

M01/M09 Hardware and Software Tools], its performance and any consequential

damages, on the use of the Product in accordance with (i) the terms of the License

Agreement and the Sale and Purchase Agreement under which agreements the

Product has been delivered, (ii) the technical descriptions and (iii) all

accompanying written materials. This product has been created to work in

laboratory environment only. In addition, to the maximum extent permitted by

applicable law, Fujitsu Mikroelektronik GmbH disclaims all warranties and

liabilities for the performance of the Product and any consequential damages in

cases of unauthorised decompiling and/or reverse engineering and/or

disassembling.

1. Fujitsu Mikroelektronik GmbH warrants that the Product will perform

substantially in accordance with the accompanying written materials

[this manual] for a period of 90 days form the date of receipt by the

customer. Concerning the hardware components of the Product, Fujitsu

Mikroelektronik GmbH warrants that the Product will be free from

defects in material and workmanship under use and service as specified

in the accompanying written materials for a duration of 1 year from the

date of receipt by the customer.

2. Should a Product turn out to be defect, Fujitsu Mikroelektronik GmbH´s

entire liability and the customer´s exclusive remedy shall be, at Fujitsu

Mikroelektronik GmbH´s sole discretion, either return of the purchase

price and the license fee, or replacement of the Product or parts thereof,

if the Product is returned to Fujitsu Mikroelektronik GmbH in original

packing and without further defects resulting from the customer´s use or

the transport. However, this warranty is excluded if the defect has

resulted from an accident not attributable to Fujitsu Mikroelektronik

GmbH, or abuse or misapplication attributable to the customer or any

other third party not relating to Fujitsu Mikroelektronik GmbH.

3. To the maximum extent permitted by applicable law Fujitsu

Mikroelektronik GmbH disclaims all other warranties, whether

expressed or implied, in particular, but not limited to, warranties of

merchantability and fitness for a particular purpose for which the

Product is not designated.

Flash-64P-M01/M09

Page 4

4. To the maximum extent permitted by applicable law, Fujitsu

Mikroelektronik GmbH´s and its suppliers´ liability is restricted to

intention and gross negligence.

NO LIABILITY FOR CONSEQUENTIAL DAMAGES

To the maximum extent permitted by applicable law, in no event

shall Fujitsu Mikroelektronik GmbH and its suppliers be liable for

any damages whatsoever (including but without limitation,

consequential and/or indirect damages for personal injury, assets of

substantial value, loss of profits, interruption of business operation,

loss of information, or any other monetary or pecuniary loss) arising

from the use of the Product.

Should one of the above stipulations be or become invalid and/or unenforceable,

the remaining stipulations shall stay in full effect.

Date: 22.01.99, V1.0

Flash-64P-M01/M09

Page 5

Contents

1. Hardware description 6

1.1 Overview 6

1.2 Features 6

1.3 General Description 6

1.4 Jumpers and Switches 7

1.4.1 Define µC operating mode (DIP switch S1) 8

1.4.2 Power supply voltage (J1, J7) 9

1.4.3 Define External Interrupts INT0, INT1 (J8, J24)

1.4.4 Configuration of RS232 Interfaces (J20 - J23, S1) 10

1.4.5 Reset Generation (J9, J10) 11

1.4.6 Configuration of the analog Interface (J2, J3, J4) 12

1.5 Serial Programming Interface 14

1.6 Related Products 15

1.7 Connectors 16

1.7.1 Edge connectors (J16, J17, J18, J19) 16

1.7.2 Serial Interface connectors X2, X3 18

1.7.3 Power connector X1 18

2. Installation 19

3. Schematics and Drawings 20

3.1 Top Assembly Flash-64P-M01/M09 evluation board 20

3.2 Schematics Flash-64P-M01/M09 evaluation board 21

Flash-64P-M01/M09

Page 6

1. Hardware description

1.1 Overview

The Flash-64P-M01/M09 is a low cost multifunctional evaluation board for the

Fujitsu 16-Bit Flash microcontroller series MB90560, MB90560L and MB90565.

It can be used stand alone for software development and testing or as a simple

target board to work with the emulator system.

The board allows the designer immediately to start with the software development

before his own final target system is available.

1.2 Features

•Supports 16-Bit LX series MB90560, MB90560L, MB90565

•Fully supports 3V and 5V environment

•QFP-64 or DIP-64 package can be used

•In-Circuit serial Flash programming

•All resources available for evaluation

•All pins routed to connectors

•4MHz main crystal

•Two UART Interfaces (3V and 5V operating)

•8 User LEDs

•Reset Button

•Two Buttons configurable for external interrupts

•Prototyping area

1.3 General Description

The Flash-64P-M01/M09 was designed to support the MB90560/L series. It can

be used as a stand alone evaluation board or as a target board for emulator

debugger. The evaluation board supports two different packages:

ØFPT-64P-M09 (square QPF64 package, 0,65mm pitch)

ØDIP-64P-M01 (shrink DIP package)

Note: The board can only be mounted with one microcontroller. So never

plug in two microcontrollers at the same time!

Flash-64P-M01/M09

Page 7

By default the board is working with a 4MHz crystal as the main oscillation

clock, so internal clock rates up to 16MHz can be generated using the internal

PLL of the µC. Two separate RS232 transceiverss can be used to connect directly

the two on-chip UARTs to the 9 pin D-Sub connectors. The transceivers generate

the adequate RS232 levels for the receive (RXD) and transmit (TXD) lines. The

DTR line of the connector is hardwired to the DSR line. The RTS signal can be

shortcut to CTS using the DIL switch setting. The UART1 interface (X3) is

always used for the in-circuit serial programming of the MB90F562/L.

If the board is used as an emulator target board, the microcontroller must be

removed from the socket and the corresponding probe cable has to be plugged in

instead. For the FPT-64P-M09 package (64 pin QFP package), use the probe

cable MB2132-461. For the DIP-64P-M01 package (64 pin DIL package), use the

probe cable MB2132-434.

All pins of the Microcontrollers are connected to the edge connectors J16-J19. So

all pins are directly available.

Note: The pin numbers of the connectors correspond to the pin numbers of

the QFP socket only! For the DIL package please use the cross reference

table at the end of this document.

The on-board line regulator allows to connect a regulated DC input voltage

between +7.5V to +12V. In case of any modifications of the board, the user has to

take care for the complete power consumption. To avoid any possible damages an

additional heat sink for the line regulator can be mounted if necessary.

There are three push buttons on the board; one Reset button and two buttons

which can be used for external interrupts.

Eight user LEDs are connected via a 1K pull up resistor network to Port 0. If this

port is used for something else, the resistor network can be removed in order to

disconnect the LEDs.

The operating mode of the microcontroller can be selected by the mode pin

setting. This setting can be done by the DIP switch S1 located on the board.

1.4 Jumpers and Switches

This chapter describes all jumpers and switches which can be modified on the

evaluation board. The default setting is shown with a gray shaded area. All

jumpers and switches are named directly on the board by its meaning, so it is very

easy to set the jumpers according to the features.

Flash-64P-M01/M09

Page 8

1.4.1 Define µC Operating Mode (DIP Switch S1)

The DIP switch S1 is used to set the operating mode of the µC and to configure

the two serial interfaces. S1/1, S1/2 and S1/3 are used to set the three mode pins

MD0, MD1, MD2 of the microcontroller. These mode pins define the operating

mode of the µC. Make sure that the mode pin setting corresponds to the usage of

the application. For more detailed information please look at the Hardware

Manual of the microcontroller series. The default setting is used for ‘Single Chip’

normal mode.

DIP switch setting Logical value

ON (closed) 0 (low)

MD0 (S1/1) OFF (open) 1 (high)

ON (closed) 0 (low)

MD1 (S1/2) OFF (open) 1 (high)

ON (closed) 0 (low)

MD2 (S1/3) OFF (open) 1 (high)

Figure 1: S1 DIP switch setting to set the Mode Pins(default: MD0,1,2 = 110,

single chip mode)

default

S1/7 and S1/8 are used to set the port pins P00 and P01. These two port pins are

used to define the serial programming mode, if the In-Circuit serial programming

of the Flash memory is used. For normal operation these port pins are used as

general I/O ports.

Note: The port pins P01 and P00 are connected to a 47K pull up resistor

each.

DIP switch setting Logical value

ON (closed) 0 (low)

P01 (S1/7)

OFF (open) 1 (high)

ON (closed) 0 (low)

P00 (S1/8) OFF (open) 1 (high)

Figure 2: S1 DIP switch setting for the Port P00 and P01 (default: P01= 0FF, P00

= OFF)

Flash-64P-M01/M09

Page 9

1.4.2. Power Supply Voltage (J1, J7)

The evaluation board can be configured to work with +3.3V or +5.25V power

supply voltage. So even the serial interfaces will work with +3.3V or +5.25V

power supply.

Note: The MB90F562 is a 5V only device. The MB90F562L is a 3V only

device. For more detailed electrical characterisations please look at the

corresponding datasheet.

DIP switch setting Description

1-2 (3V3) On board power supply is

3.3V

3V3/5V power Supply

(J1) 2-3 (5V) On board power supply is

5.25V

Figure 3: J1 jumper setting for the Power Suppy voltage (default: 2-3(5V)=5.25V

Power Supply)

NOTE:

If the evaluation board is used with the MB90560L or MB90565 series (low

voltage series), the supply voltage for the µC must be switched to

Vcc=3.3V(Jumper setting J1). Additional it is necessary to connect manually

the C-Pin to Vcc by a wire. Otherwise it could happen that the µC does not

work correctly! (C-Pin: Connector J 18/pin 57 for QFP package, Connector

J17/pin1 for DIL package)

The Jumper J7 is used to connect the Vcc supply voltage to the µC. This jumper

was assigned e.g. to measure the Icc current for the µC separately.

Jumper setting Descri

ption

ON (closed) Power supply Vcc connected

to µC

Vcc (J7)

OFF (open) Power supply Vcc

disconnected from the µC

Figure 4: J7 jumper setting for Vcc power Supply (default: J7= 0N)

Flash-64P-M01/M09

Page 10

1.4.3 Define External Interrupts INT0, INT1 (J8, J24)

J8 and J24 are used to connect the push buttons INT1 and INT0 to the external

interrupts INT1 and INT0. The push buttons are connected to the external

interrupts INT0 and INT1. Additionally a 10k/10µF RC low pass filter is used for

both interrupt inputs to suppress glitches.

Jumper setting Description

ON (closed) INT0 connected to

push button INT0

INT0 (J8)

OFF (open) No connection

ON (closed) INT1 connected to

push button INT1

INT1 (J24)

OFF (open) No connection

Figure 5: J8, J24, Jumper setting to connect external interrupts (default: J8= 0N,

J24 = ON)

To disconnect the low pass filter and the push buttons, just remove the

corresponding jumper.

1.4.4 Configuration of the RS232 Interfaces (J20 - J23, S1)

J20 – J23 are used to connnect the two on board serial transceivers to the UART0

and 1 interface of the microcontroller. J20 and J21 are used to connect the

UART0 interface, J22 and J23 are used to connect the UART1 interface. The

jumpers are used to connect the TTL outputs (RXD, TXD) of the serial drivers to

the µC. If the UART interface is not used, the corresponding jumpers should be

left open.

Jumper setting Description

ON (closed) SIN0 connected

SIN0 (J20) OFF (open) No connection

ON (closed) SOT0 connected

SOT0 (J21) OFF (open) No connection

Figure 6: J20, J21 jumper setting for the Serial Interface (default: SIN0= 0N,

SOT0 = ON)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Hauptplatine Handbücher

Fujitsu

Fujitsu MB2146-450-E Bedienungsanleitung

Fujitsu

Fujitsu D3011 Bedienungsanleitung

Fujitsu

Fujitsu SK-MB91590-208M04 Bedienungsanleitung

Fujitsu

Fujitsu D2779 Bedienungsanleitung

Fujitsu

Fujitsu D2679-B11 Bedienungsanleitung

Fujitsu

Fujitsu D1567 Bedienungsanleitung

Fujitsu

Fujitsu GA-8SGXL P4 Titan DDR Bedienungsanleitung

Fujitsu

Fujitsu F2MC-16L Series Bedienungsanleitung

Fujitsu

Fujitsu D2542 Bedienungsanleitung

Fujitsu

Fujitsu D2811 Bedienungsanleitung

Fujitsu

Fujitsu D1826-G Bedienungsanleitung

Fujitsu

Fujitsu D3141 Bedienungsanleitung

Fujitsu

Fujitsu D2785 Bedienungsanleitung

Fujitsu

Fujitsu D3003 Bedienungsanleitung

Fujitsu

Fujitsu MB9B500 Series Bedienungsanleitung

Fujitsu

Fujitsu MS-6191 Bedienungsanleitung

Fujitsu

Fujitsu MB91360 SERIES Bedienungsanleitung

Fujitsu

Fujitsu D1692 Bedienungsanleitung

Fujitsu

Fujitsu P4 Titan-DDR GA-8STXC Bedienungsanleitung

Fujitsu

Fujitsu GA-8STXC P4 Titan-DDR Bedienungsanleitung

Fujitsu

Fujitsu D3161 Bedienungsanleitung

Fujitsu

Fujitsu FLASH-CAN-100 Bedienungsanleitung

Fujitsu

Fujitsu D3231-S Bedienungsanleitung

Fujitsu

Fujitsu D3173 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung