Fujitsu FTP-639MCL354 Betriebsanleitung

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

THERMAL PRINTER

FTP-639MCL354

PRODUCT

SPECIFICATION

02.08.22Ｈ．Ｏｈｔｓｕｋａ

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

−

Table of Contents

−

．

Guideline for product recycling

．

Product design, warnings and cautions for using the product

2-1. Handling the printer

2-2. Notice on installation and settings

2-3. Paper to be used

2-4. Cleaning

2-5. Storing

2-6. The supply method of rolled paper

2-7. Others

3. Specifications

3-1. Application

3-2. Overview

3-3. Structure

3-4. Standard specifications

3-5. Outer dimensions and installing position

3-6. Connector (flexible) specifications

3-7. Thermal head specifications

3-8. Stepping motor specifications

3-9. Sensor specifications

．

Product model plate

．

Packing

．

Pre-printing specifications

．

Revision history table

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

1.Guideline for product recycling

•Fujitsu Component Co., Ltd. is making an effort to promote the environmentalmanagement per ISO 14001 with

a policy “Better corporate activities while valuing the environment”

•The below lists the components and their materials used in this printer. Refer this list when the printer is to be

recycled.

FTP-639MCL3５4List of materials

No. Name of components Material

1Printer frame(gear side) Zinc alloy

2Printer frame (center) Zinc alloy

3Printer frame (switch side) Zinc alloy

4Gear cover POM resin

5Rubber roller Silicone rubber + SUM

6Platen gear, middle gears 1 and 2 POM resin

7Pulse motor SPCC + iron + copper wire

8Paper guide PPE resin

9Platen open lever SUS

10 Thermal head Aluminum + ceramic substrate

11 Head pressuring spring SUS

12 Bearing Sintered alloy

13 FPC PI, copper leaf, solder plating

14 Auto cutter *1

【Abbreviations for the materials used】

SUS: Stainless steel

POM: Polyacetal resin

PC: Polycarbonate

SPCC: Rolled steel plate

PI: Polyimide

PPE: Polyphenylene Ether

*1:Please refer to specifications of FTP-639CT001.

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

2.Product design, warnings and cautions for using the product

2-1. Handling the printer

(1) When handling this printer, be sure to take any preventive measure against static electricity

such as Disposable Wrist Strap in order to prevent damages of inner parts of the printer

caused by the static electricity.

(2) The thermal head and FPC are shipped as they are connected. When installing the printer,

do not pull or apply any extra force in order to avoid the connected part of the thermal head

and FPC from being disconnected or deviated. Using the printer with the part is deviated

may destroy the head. If it is deviated or disconnected, contact us.

In addition, for the connection of FPC and the control circuit side, as shown in the figure

below, the checking mark for attachment is seen on FPC; therefore, follow the mark and

make sure not to deviate when attaching.

(3) Never attempt to touch FPC and the probe part of the signal line of FFC (parts which are

soldering-plated) and not to hit them with something hard.

(4) Do not perform the contact bending of FPC because it may cause the disconnection. If

FPC requires to be bent, the bending should be more than R1. Once it is bent, do not

rework (straighten or bend backward).

（5）If any paper ejected from this printer is pulled away with an unnecessarily strong force when

the platen-open lever is open,it may cause the platen gear to get off the track and damage the

gear. Do not attempt to pull any paper ejected from the printer.

(6) If any voltage is applied to the thermal head when the head or paper is wet due to

condensation, it may be damaged by electrolytic corrosion; therefore, when using the printer,

pay attention to the following items.

＊Do not apply any electric power to the printer when it is not used.

＊Do not perform the printing with any wet paper.

＊Do not apply any electric power to the printer under any environment where any dew

condensation is possible to occur.

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

＊Turn off all electric power to the head immediately when condensation occurs. Use

the head only after the head is completely dried.

＊Depending on the environment where the printer is used (the low temperature or high

humidity), condensation may be caused by water vapor generated from the used paper

when performing the printing of the high printing rate (solid fills, zigzag printing);

therefore, the environment should be considerably evaluated.

（7）When any paper is not set at the printer,be sure to lift down the platen-release lever. If the

paper is run out during the printing,stop all actions of the printer in order to prevent the

printing without the paper fed. If the printing is continued without any paper fed,it may

cause the trouble of the printer.

（8）When using this printer for the continuous actions, the temperature of the head printer board

(the detected temperature with the thermistor) should be equal or less than 65 degrees

Centigrade for the temperature protection of IC inside of the printer as well as the surface

temperature of the motor should be equal or less than 90 degrees Centigrade for he

temperature protection of the motor coil.

2-2Notice on installation and settings

(1) When installing the printer,fix the edge part with a hook at two places and fix the rear part

with screws of M3 at two places. Flatness of the installing surface of the printer should be

within equal or less than 0.1mm. It is recommended that the printer is connected to the

main body FG with screws of M3 at two places (refer to the figure of the installation

dimension). Pay attention not to apply any extra force to the printer main body,FPC since

any of such force will give unfavorable effects to the printing quality,paper traveling

property (meandering,running short of the paper,and the paper jam),and life time.

(2) Then installing the printer,install it so that the printer and the rolled paper should be parallel

as much as possible. When designing the casing,it should be designed so that the printer

and the holder part of the roller paper are located at the place shown in the bellow figure.

The roller paper should be ejected smoothly so that the paper does not hit anything such as

the cover. If the above is not conformed,troubles such as meandering of the printing paper,

the running short of the paper,and the paper jam may occur.

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

(3) When plugging in and out FPC to the connector of the control side, be sure that all power is

turned off before doing that.

(4) Use our recommended connector as the one of the control side of FPC. If any other

connector is used, fully confirm the properties (the contact resistance, drawing strength, and

the allowable power supply voltage) before using.

(5) The back tension of the rolled paper should be equal or less than 1.96N (200g) including the

start up. If it exceeds equal or greater than 1.96N, the platen gear may get off the track and

causes to damage the gear.

(6) For the attitude of mounting the cutter, follow the instructions below.

Attitude C: Do not use C because paper chips intrude the cutter.

2-3Paper to be used

（1）Regarding the printing quality and lifetime; therefore, carefully confirm the property of the

paper before using.

（2）When using the perforated paper, the punching direction of the perforations should be set to

face the thermosensitive side. The height of burrs of the perforations and dusts of them may

cause troubles such as deterioration of the printing quality, the paper end sensor, the platen

gear’s getting off the track, and the lifetime; therefore, carefully check the perforated paper

before using.

（3）To reduce the loads during the paper feeding and to improve the sensitivity of the paper end

sensor, when rolling the paper, the thermosensitive side of the paper should be faced outside.

（4）Use the rolled paper of which inner diameter should be equal or greater than φ8 (the

diameter when there is not core).

2-4Cleaning

Paper residues or foreign matter may shorten the life of the head or platen. Clean the

printer periodically.

2-5Storing

（1）When storing the printer for the long-term (equal or longer than six months at the room

temperature), lift down the platen-release lever and insert the paper between the head and the

platen. If the rubber part of the platen and the head have continued to directly contact for a

long term, the rubber part will be deformed and may affect the quality of printing.

（2）Do not store the printer in damp places and places with drastic temperature variations.

Condensation on the printer may cause troubles such as thermal head damages and action

failures.

（3）Do not store the printer in dusty places. Using the printer with dusts adhered on it may

cause troubles to the printing and actions.

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

2-6The supply method of rolled paper

(1) When printing in the paper supplied from rolled paper, printing disorder may

occur according to the inertia of rolled paper at the time of a printing start.

When you use the rolled paper exceeding φ80mm, please establish the

mechanism for a shock buffer between rolled paper and a printer.

2-7Others

(1) If any trouble occur, it shall be solved by mutual discussion based on this specification.

Only the printer is subject to quality assurance.

(2) Changes and additions that do not have compatibility of this specification shall be carries out

according to the mutual discussion. However, because this printer is the standard model,

changes can be carried out without notices within a range where compatibility exists.

(3) This thermal printer comes with an 18-month warranty after the date of production (printer

serial No.). Any failure caused by the customer side in the warranty period and after expiry

of the warranty shall be serviced with charge. The maintenance service can be available in

five year after the date of discontinuation of producing this printer.

(4) This printer does not provide the dust-tight and drip-proof structure. Take measures for the

dust-tightness and drip-proof from the main body casing side,as required.

(5) Surfaces and edge surfaces of metallic parts may change colors; therefore,take measures for

discoloration as required,such as covering with a casing.

(6) Smoke may be generated from parts of the printer; therefore,take measures for preventing

any foreign conductive materials from entering the inside as required,such as covering with

a casing.

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

3. Specifications

3-1Application

This specification is applies to FTP-639MCL354.

Standards by this specification are satisfied by standard interface .

3-2Overview

This printer is the small and lightweight printer which build in a line dot thermal head of resolution 8

dots /mm..

The auto cutter is carried in this printer. These specifications should presuppose that it is main with

the specification of a printer part, and refer to the following product specifications for the

specification of an auto cutter.

FTP-639CT001 Auto cutter specification

3-3Structure

Below is the figure of this printer's structure (the mechanical part).

Flexible cable for head Flexible cable for motor & sensor

Platen Release switch Motor

Deceleration

gear

Thermal head

Platen unit

Photo sensor (paper detect sensor)

Cutter frame

Auto cutter

Printer

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

3-4Standard specifications

Item Specifications

Printing method Direct thermosensitive method

Valid printing width 72 mm

Dot ｓｔｒｕｃｔｕｒｅ 576 dots /line

Dot pitch(rsolution) 0.125 mm (8 dots/mm)

Dot size 0.125mm×0.16mm

Printing ｄｅｎｓｉｔｙ OD value greater than 0.8, in use of the specified paper under our standard printing

conditions.

※Measuring device: Sakura densitometer, PDA-65, by Konika Co., Ltd.

Printing specifications

Printing speed 200mm/s [24V drive, Standard paper(PD150R equivalent), Room temperature,

High speed mode]

Highly sensitive

paper TF50KS-E4 (width: 82.5+0

-1mm), Nippon Paper

TF60KS-E (width: 82.5+0

-1mm), Nippon Paper

Standard

paper PD150R (width: 82.5+0

-1mm), Oji Paper

TP60KS-F1 (width: 82.5+0

-1mm), Nippon Paper

P220VBB-1 (width: 82.5+0

-1mm), Mitsubishi Paper

Middle-term

ｐｒｅｓｅｒｖａｂｌｅ

PD170R (width: 82.5+0

-1mm), Oji Paper

TP50KJ-R (width: 82.5+0

-1mm), Nippon Paper

AFP-235 (width: 82.5+0

-1mm), Mitsubishi Paper

PD160R-N (width: 82.5+0

-1mm), Oji Paper

Specified paper for recording *1

Long-term

ｐｒｅｓｅｒｖａｂｌｅ

HA220AA (width: 82.5+0

-1mm), Mitsubishi Paper

Paper feeding

method Friction feeding (1 dot line/2 pulses, bi-polar 1-2 phase excitation)

Paper feeding precision ±5% At fixed-speed feed with the back tention ｏｆ 0.49N ｏｒ less (±2% at

25℃and RH 60％)

Line gap in one print

line by enable drive Less than 0.125 mm, the step difference between the right and left printing lines.

Thermal head

temperature

detection Thermistor

Paper detection

Mark detection

Photo interrupter

Detective functions

Platen release Sliding swich

External dimensions

(W x D x H) 109.7±1mm×62.5±0.5mm×37.7±0.5mm (excluding FPC)

Refer to the outer dimension drawing in section 3-5 for details.

Weight

Approx320g

Average resistance of

the ｔｈｅｒｍａｌ head 800 Ω±3%

*1:If any other paper except for the specified above is used, through the mutual discussion, the paper shall be

evaluated, checked and adoption shall be determined.

FTP-639MCL354 SPECIFICATION

A1NA02273-0354

Dept. to control the original documentDate

Date

Rev.

Design

Inspection

Inspect.

Changes made

Approv.

FUJITSU COMPONENT LIMITED

Name

Drawing

No.

Page

Submit to

Item Specifications

For printing Voltage: DC 24V±5%,Printing speed:200mm/s

Peak current: 4.0A (at 25℃, Rav=800Ω, ２４ V, printing black ratio 25%)

Head

For logic Voltage: DC 5V±５%

Current: 0.2 ＡMax.

Drive power

Motor drive Voltage: DC 24V±5%

Current: 1.0 A Max. (by the F&T standard constant-current drive circuit)

Operating

temperature and

humidity *1

0℃〜+50℃, 20〜85％RH. No dew should be allowed.

Temperature and

humidity in storage -20℃〜60℃, 5〜95％RH. No dew should be allowed. Yet, the paper is not

included.

Environmental

characteristics

Noise Should not exceed 60dB at a point 1 m above from the printing mechanism

position level.

Vibration

(non-operation) 10〜55〜10Hz. Amplitude is 0.15mm. An １octave/min, １G Max. 20 cycle

each to X, Y, and Z directions.

Inpact

(non-operation) 50Ｇ, 11ｍ/ｓ, half-sine wave, 5 times each to X, Y and Z direction

Package drop 75 cm of 6 faces, 75 cm of corners and ridges as it is packed.

Reliability

characteristics*2

Temperature &

humidity cycling

(non-operation)

2 continuous cycles as a unit cycles: -25℃（2H）〜room temp. （2H）〜65℃,

10％RH (2H）〜room temp.

Electric life 1 hundred-million pulses (under our standard printing conditions.)

Head

Wear life Paper feed length, 100 km (printing rate 12.5% max.)

Platen release life More than 5000 times (regarding opening and closing as one time.)

Life

Photo interpreter

life 1.2×10４hours (electrified time) with the recommended circuit.

Printing start position on

the left edge 5.25±1.5mm (by paper width 82 mm) from the paper edge to the left printing

edge. However, ①１PLY, when the specified paper for long-term record

storage is used.②When no paper jam or no paper empty is present.

*1:The Print density guarantee is +5~+40C. Refer to the figure below for the relation

of the temperature and humidity.(The range is in fat line)

*2:After the test, it shall satisfy the printing specification. (%RH)

0 40 50(℃)

Inhaltsverzeichnis

Andere Fujitsu Drucker Handbücher

Fujitsu

Fujitsu FTP-621CDL003 Bedienungsanleitung

Fujitsu

Fujitsu FTP-629DCL014R Bedienungsanleitung

Fujitsu

Fujitsu FP-510II Bedienungsanleitung

Fujitsu

Fujitsu 10 ppm Bedienungsanleitung

Fujitsu

Fujitsu DL6400PRO Bedienungsanleitung

Fujitsu

Fujitsu DL2400 Bedienungsanleitung

Fujitsu

Fujitsu fi-4x20 SERIES Konfigurationshandbuch

Fujitsu

Fujitsu DL3700 Pro Bedienungsanleitung

Fujitsu

Fujitsu RS-232C Bedienungsanleitung

Fujitsu

Fujitsu 16DV Bedienungsanleitung

Fujitsu

Fujitsu PrintPartner 10V Bedienungsanleitung

Fujitsu

Fujitsu DL9300 Bedienungsanleitung

Fujitsu

Fujitsu DL6400PRO Bedienungsanleitung

Fujitsu

Fujitsu FTP-621CT001 Bedienungsanleitung

Fujitsu

Fujitsu M304X series Handbuch

Fujitsu

Fujitsu FTP-608 Series Bedienungsanleitung

Fujitsu

Fujitsu Printer Bedienungsanleitung

Fujitsu

Fujitsu 628WSL110H2 Bedienungsanleitung

Fujitsu

Fujitsu ApeosPrint C4030 Bedienungsanleitung

Fujitsu

Fujitsu FTP-040HF Holder Series Bedienungsanleitung

Fujitsu

Fujitsu FTP-621DCL012 Bedienungsanleitung

Fujitsu

Fujitsu DL5600 Bedienungsanleitung

Fujitsu

Fujitsu fi-4530C Konfigurationshandbuch

Fujitsu

Fujitsu DL-3700 Installationshandbuch

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung