Fujitsu Fi-4860C Referenzhandbuch

Fujitsu SCSI (650) VRS Scanner Installation Procedures

Windows ME\2000\XP

If you are installing the following models by means of the Kofax 650 Adrenaline SCSI

controller with/without a GSA-2 then use this document.

M4097D-VRS M4099D-VRS Fi-4860C-VRS Fi-4990C

Fi-5650C-VRS Fi-5750C-VRS

If you do not have a 650 controller and are not going to use VRS then use the SCSI

scanner installation guide. If you are going to use the optional video interface then use

the video scanner installation guide. If you have an 850S/1700S controller and a GSA-1

interface then you must use the SCSI (GSA-1) VRS scanner installation guide.

Hardware requirements.

You will need a PC system that meets both Fujitsu’s and Kofax’s recommended

specifications, a Kofax 650 Adrenaline controller and six foot (maximum) Wide SCSI 68-

pin cable. For recommended PC system specifications and SCSI controllers please

reference the Scanner Hardware Reference page. You may also need your Operating

System Disk.

Step A: Installing the VRS drivers.

First boot your PC and install the Kofax VRS driver that shipped with the scanner.

Special note: When installing the VRS driver and any other software that contains

Kofax’s Image Controls pay close attention to the individual runtimes. It is strongly

recommended that you install the oldest/lower runtime application first.

Step B: Installing the Adrenaline 650 Adrenaline controller

1. Shut down your PC and remove the case cover.

2. Locate a free PCI slot and remove the back plate if necessary.

3. Install the SCSI controller in an open PCI slot. Make sure that the card is

seated completely in the slot and secured in the frame.

Warning! Failure to secure the SCSI controller in the PC can result in damage

to the SCSI card, scanner, and/or your system.

4. Boot your PC without the scanner attached and check for errors. Make sure

that the SCSI controller is listed as a 650 Adrenaline. If no errors proceed to

the next step.

Step C: Unlocking the shipping lock.

If your model scanner does not have a flatbed then proceed to Step D.

Rev052206A Page 1 of 3

Fujitsu SCSI (650) VRS Scanner Installation Procedures

Windows ME\2000\XP

The flatbed model scanners typically include a lock on the flatbed designed to

protect the scanner during shipment. Before the scanner can be used the

shipping lock must be unlocked. To unlock it do the following:

1. Located the shipping lock slider tab or knob underneath the end of the

scanner.

2. Slide or rotate the lock to the unlock position.

If your model has the old style “L” bracket shipping lock.

3. Slide the scanner to its side as shown in figure below.

4. Unscrew the retainer screw and remove the shipping bracket.

5. Place the shipping bracket in the “use position” slot and secure it with the

retainer screw (see figure below)

6. Place scanner back in its normal position

Rev052206A Page 2 of 3

Fujitsu SCSI (650) VRS Scanner Installation Procedures

Windows ME\2000\XP

Step D: Connecting the Scanner.

Warning! Before proceeding ensure that the power is off when connecting or

disconnecting the SCSI cable to the scanner or workstation. Failure to follow the

procedure above could result in damage to the SCSI card, scanner, and/or your system.

Termination and the SCSI ID’s for the scanners are handled automatically.

Connect the SCSI cable to the Kofax controller and to the Wide SCSI (68-pin)

port on the scanner. Ensure all connections are securely fastened.

Connect the power cord to the scanner and a wall outlet. Turn on the scanner

first and when it reports ready boot up your PC. Complete the new hardware

found wizard and go to the next step.

Step E: Scanning with VCDEMO32P.

1. Go to Start, Programs, Kofax VRS or Kofax Image Controls, and select

VCDEMO32P.EXE.

2. Next go to Source, Scanner, and click on the drop down arrow; then

select your scanner model. I.E. Fujitsu fi-4860C with VRS with AIPE.

Wait a few seconds for the Kofax engine to load, and then place your

documents in the scanner.

3. Now go to Source, Properties and select your scanning parameters (i.e.

scan source - Flatbed or ADF, resolution, paper size).

4. You may also access the VRS configuration settings at this time by clicking

on Advance Properties. The AIPE functions are access via the Imaging

menu.

5. Afterwards go to Source, and click on Process Image for single page scans

or Process Batch for multi-page batch scans.

Congratulations! You have successfully completed and tested your VRS scanner

installation.

Step F: Installing third party software applications.

After you have successfully installed all the Fujitsu software and hardware, then it is time

to install any additional third party scanning software that you wish to use. Please follow

the software manufacturer’s instructions for installation. Remember when installing any

software that contains Kofax’s Image Controls pay close attention to the individual

runtimes. It is strongly recommended that you install the oldest/lower runtime

application first.

Rev052206A Page 3 of 3

Andere Handbücher für fi-4860C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Scanner Handbücher

Fujitsu

Fujitsu M4099D Bedienungsanleitung

Fujitsu

Fujitsu fi-6130Z Bedienungsanleitung

Fujitsu

Fujitsu fi-6670 Series Bedienungsanleitung

Fujitsu

Fujitsu M3096EX/GX Handbuch

Fujitsu

Fujitsu ScanSnap fi-5110EOX Handbuch

Fujitsu

Fujitsu ScanSnap S1100 Handbuch

Fujitsu

Fujitsu fi-6800 Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap S1100i Montageanleitung

Fujitsu

Fujitsu fi-6670 Series Handbuch

Fujitsu

Fujitsu fi-4640S Handbuch

Fujitsu

Fujitsu FI-6130 Konfigurationshandbuch

Fujitsu

Fujitsu fi-4860C Handbuch

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Bedienungsanleitung

Fujitsu

Fujitsu fi-7140 Bedienungsanleitung

Fujitsu

Fujitsu ScanPartner 15C Bedienungsanleitung

Fujitsu

Fujitsu M3099EX Bedienungsanleitung

Fujitsu

Fujitsu S510M - ScanSnap - Document Scanner Konfigurationshandbuch

Fujitsu

Fujitsu CardMinder Series Bedienungsanleitung

Fujitsu

Fujitsu SNAPSNAP IX500 Bedienungsanleitung

Fujitsu

Fujitsu Fi-7030 Handbuch

Fujitsu

Fujitsu FI-5530C2 Konfigurationshandbuch

Fujitsu

Fujitsu FI-4860C2 Konfigurationshandbuch

Fujitsu

Fujitsu S510 - ScanSnap - Document Scanner Bedienungsanleitung

Fujitsu

Fujitsu M4099D Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung

Visioneer

Visioneer CardReader 100 Kurzanleitung

Rohde & Schwarz

Rohde & Schwarz TSME6 Bedienungsanleitung

Fujitsu fi-4860C Referenzhandbuch

Beliebte Scanner Handbücher anderer Marken