Fujitsu SCANPARTNER 600C Bedienungsanleitung

ScanPartner 600C

Image Scanner

User’s Manual

Version 1.0

(Doc. No. 250-0062-0)

Table of Contents

1. INTRODUCTION ………………………………… 3-4

2. INSTALLATION AND CONNECTIONS ………. 5-13

2.1 Shipping Bracket ……………………………………………… 5

2.1.1 Removing the Shipping Bracket …………………………….. 5-6

2.1.2 Refitting the Shipping Bracket ………………………………. 7

2.2 SCSI Interface Device ID …………………………………….. 7-8

2.3 ADF Paper Chute ……………………………………………… 9

2.4 ADF Output Tray ……………………………………………… 10

2.5 Document Loading ……………………………………………. 11

2.6 ADF Scanning …………………………………………………. 12

2.7 Connecting the Cable …………………………………………. 13-14

3. MAINTENANCE ………….………………………. 15-17

3.1 Cleaning the ADF ……………………….…………………….. 15-16

3.2 Cleaning the Glass ……………………………………………. 17

4. TROUBLESHOOTING ……………….………….. 18-21

4.1 Question and Answer ………………………………………… 18-20

4.2 Paper Jam in the ADF ………………………………………… 20-21

5. SPECIFICATIONS ………….…………………….. 22

5.1 Model: ScanPartner 600C ………………………………….…. 23

1. INTRODUCTION

Congratulations on your purchase of a Fujitsu ScanPartner 600C Image Scanner.

Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you

with the proper instructions on how to unpack, install, operate and maintain the Scanner.

Figure 1-1 shows how the Scanner is packed. You can check all items against the “checklist”, included with your

Scanner.

Figure 1-1 - Scanner Packing

User Manual

Output Paper Tray

Image Scanner

Power Cable

Foam

Carton

2. Installation and Connections

Please unpack the Scanner carefully and check the contents against the “checklist”. If any items are missing or

damaged, please contact your authorised local dealer immediately.

Precautions:

vKeep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause

damage to the unit.

vDo not install the Scanner in a humid or dusty place.

vBe sure to use the proper AC power source.

vPlace the Scanner securely on an even, flat surface. Tilted or uneven surfaces may cause mechanical

or paper-feeding problems.

vRetain the Scanner box and packing materials for shipping purposes.

2.1 Shipping Bracket

The Scanner has a bracket that locks the carrier mechanism for transportation purposes. This bracket must be

put into the use position before using the Scanner.

Note:

If the power is turned on before the bracket has been removed the PAPER JAM light will

turn on. Before proceeding, turn the power off, disconnect all cables and follow the

instructions below to remove the shipping bracket.

2.1.1 Removing the Shipping Bracket (refer to figures 2-1 and 2-2)

i) Carefully place the Scanner in an upright position on its front.

ii) Using a suitable screwdriver, remove the screw and pull out the shipping bracket.

iii) Put the shipping bracket into the use position with the short side extending into the scanner

base and secure it with the screw.

vi) Carefully place the Scanner back into its normal position.

Figure 2-1 - Removing the Shipping Bracket

Figure 2-2 - Securing the Shipping Bracket

Shipping Position

Use Position

2.1.2 Refitting the Shipping Bracket

Whenever you need to move the Scanner to a new location it is advisable to refit the shipping bracket

to avoid causing damage to the Scanners’ internal mechanism. Please follow the instructions below

to refit the shipping bracket.

i) Turn off the Scanner power at the power on/off switch.

ii) Disconnect all cables.

Note: For steps (iii) to (vi) please refer to figures 2-1 and 2-2

iii) Carefully place the Scanner in an upright position on its front side.

iv) Using a suitable screwdriver remove the screw holding the shipping bracket in the use

position.

v) Put the shipping bracket into the shipping position, with the long side extending into the

Scanner base. Secure it with the screw.

vi) Carefully place the Scanner back into its normal position.

2.2 SCSI Interface Device ID

When you have several devices on a SCSI chain, you may need to adjust the SCSI ID selector setting located

on the back of the Scanner. This setting assigns a specific “device ID” to the Scanner. If the assignment

conflicts with an existing SCSI device, please select a new ID (see Figure 2.3).

Note: The factory setting for the Scanner is ID 6. Usually, ID 0 is assigned to an internal hard disk drive,

and ID7, to SCSI adapter or host. ID 8 and 9 are not in actual use.

Using a suitable tool, turn the selector switch until the arrow points to the desired ID number.

Figure 2-3 - Adjusting the SCSI ID Setting

SCSI ID Selector

2.3 ADF Paper Chute (Figure 2-4)

i) Raise the right side of the paper chute to about 45 degrees.

ii) Pull down the wire leg from under the paper chute •.

iii) Insert the wire leg into the grips on the document cover ‚.

iv) Pull out the paper chute extension to the length you want.

Figure 2-4 - Setting the ADF Paper Chute

ADF Paper Chute

Document Cover

2.4 ADF Output Tray (Figure 2-5)

i) Hold the output tray at an angle as shown in figure 2-5.

ii) Insert the three protrusions on the paper output tray to the three slots on the ADF •.

iii) Lower the paper tray gently ‚. Make sure the tray is firmly attached to the ADF.

iv) Pull out the output tray extension wire to the desired length.

Figure 2-5 - Install the ADF Output Paper Rack

Extensions

Andere Handbücher für SCANPARTNER 600C

Inhaltsverzeichnis

Andere Fujitsu Scanner Handbücher

Fujitsu

Fujitsu FI-5120 Bedienungsanleitung

Fujitsu

Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Bedienungsanleitung

Fujitsu

Fujitsu M3093DE Konfigurationshandbuch

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Handbuch

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

Fujitsu

Fujitsu FI-5015C Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Bedienungsanleitung

Fujitsu

Fujitsu fi-5650C Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap S500 Handbuch

Fujitsu

Fujitsu ScanSnap S1300i Montageanleitung

Fujitsu

Fujitsu fi-6800 Bedienungsanleitung

Fujitsu

Fujitsu FI 6140 - Document Scanner Bedienungsanleitung

Fujitsu

Fujitsu S500M - ScanSnap - Document Scanner Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap S500 Bedienungsanleitung

Fujitsu

Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm... Handbuch

Fujitsu

Fujitsu FI-6750S Bedienungsanleitung

Fujitsu

Fujitsu FI-4120C Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Handbuch

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Bedienungsanleitung

Fujitsu

Fujitsu ScanSnap iX1600 Konfigurationshandbuch

Fujitsu

Fujitsu fi-6130Z Handbuch

Fujitsu

Fujitsu M3097DE Bedienungsanleitung

Fujitsu

Fujitsu S1500M - ScanSnap - Document Scanner Handbuch

Fujitsu

Fujitsu FI-400F Handbuch

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung

Visioneer

Visioneer CardReader 100 Kurzanleitung

Rohde & Schwarz

Rohde & Schwarz TSME6 Bedienungsanleitung