Fujitsu ScanSnap iX1500 Konfigurationshandbuch

iX1500

Consumable Replacement and Cleaning Instructions

CG00002-299901 Revision A

iX1500 Daily Care and Consumable Replacement Guide

This section describes how to clean the scanner.

Cleaning Materials

ATTENTION

In order to use the cleaning materials safely and correctly, read the precautions on each product thoroughly.

Do not use aerosol spray or spray that contains alcohol. Paper dust blown up by strong air from the spray

may enter inside the scanner which may cause the scanner to fail or malfunction.

Also note that sparks generated by static electricity may cause a fire.

The inside of the ADF becomes very hot when the scanner is being used. Before you start cleaning the inside

of the ADF, make sure to turn off the power, unplug the power cable and wait for at least 15 minutes for the

inside of the ADF to cool down.

For more Information about the cleaning materials, contact the distributor/dealer where you purchased this product.

Or, make an Inquiry by referring to the contact Information at the Contact for Inquiries section In Safety Precautions

bundled with this product.

Cleaning the Inside of the Scanner

Clean the inside of the ScanSnap regularly.

Scanning repeatedly accumulates dust and paper dust inside the ScanSnap, and this may result in an error during a scan.

As a guideline, the inside of the ScanSnap should be cleaned every 1,000 sheets scanned.

Note that this guideline varies depending on the types of documents you scan. For instance, it may be necessary to clean

the scanner more frequently when you scan documents on which the toner is not sufficiently fused.

Notice

-The bottom part of the ScanSnap may become hot when the ScanSnap is being used but this does not affect

ScanSnap operation or cause any physical harm. Be careful not to drop the ScanSnap when carrying it.

-Do not use water or mild detergent to clean the inside of the ScanSnap.

-It may take a long time for Cleaner F1 to dry if an excessive amount is used. Moisten the cloth with a moderate

quantity.

Wipe off the cleaner completely to leave no residue on the cleaned parts.

Cleaning Procedure

(1) Unplug the power cable from the ScanSnap.

(2) Remove any documents from the ADF paper chuter (cover).

(3) Remove the Receipt Guide from the scanner when it is attached.

To remove the Receipt Guide, hold it with one hand and lift it up towards you.

(4) Pull the ADF release tab to open the ADF top section.

(5) Clean the following parts with a cloth moistened with Cleaner F1, or a cleaning wipe.

1. Brake roller (x2)

Remove the brake rollers from the scanner to clean.

Gently wipe the dirt and dust off from along the slots on the surface of the brake rollers. Be careful not to

damage the surface of the rollers.

2. Glass (x2)

Gently wipe the dirt and dust off the surface of the glass sections. Make sure that it is cleaned properly

because dirty glass can cause vertical lines to appear in the scanned image.

3. Ultrasonic sensor (x2)

Gently wipe the dirt and dust off the surface of the ultrasonic sensors.

If you have trouble wiping the ultrasonic sensors with the cloth, use a cotton swab.

4. Pick roller (x1)

Remove the pick roller from the scanner to clean.

Gently wipe off the dirt and dust along the grooves on the roller surface. Residue on the roller

may affect the feeding performance. Be careful not to damage the surface of the roller.

5. Plastic idler roller (x2)

Gently wipe the dirt and dust off the rollers as you rotate them manually. Be careful not to damage the

surface of the rollers. Make sure that they are cleaned properly because residue on the rollers will affect the

feeding performance.

6. Rubber idler roller (x2)

Gently wipe the dirt and dust off the rollers as you rotate them manually. Be careful not to damage the

surface of the rollers. Make sure that they are cleaned properly because residue on the rollers will affect the

feeding performance.

(6) Connect the power cable of the ScanSnap to the AC outlet.

Reference

Connect the power cable only when cleaning the Feed-Roller and the Exit-Roller.

(7) Tap in the home screen on the touch panel of the ScanSnap to display the [Settings] screen.

(8) Tap to display the [Maintenance] screen.

(9) Tap [Roller cleaning] to display the [Roller cleaning] window.

(10) Holding down the [Run] button to rotate the Feed-Roller and the Exit-Roller.

Reference

Release the [Run] button to stop the Feed-Roller and the Exit-Roller.

(11) Clean the following parts with a cloth moistened with Cleaner F1, or a cleaning wipe.

7. Feed-Roller (x2)

8. Exit-Roller (x2)

Gently wipe the dirt and dust off while taking care not to damage the surface of the rollers. Make sure that

they are cleaned properly because residue on the rollers will affect the feeding performance.

(12) Close the ADF top section.

Cleaning the Outside of the Scanner

Scanner

The scanner including the ADF paper chute (feeder) and the stacker should be cleaned with either a piece of dry

cloth, a cloth moistened with Cleaner F1/mild detergent, or a sheet of Cleaning Wipe.

Touch screen

To avoid the surface of the touch screen becoming dirty, clean it regularly by gently wiping dirt and dust off with

a soft, dry cloth.

Clean the touch screen with care. Do not rub or tap the surface with hard objects as doing so may damage the

surface.

ATTENTION

To avoid deformation and discoloration, never use paint thinner or any other organic solvents.

Be careful not to let any moisture or water inside the scanner during cleaning.

It may take a long time to dry if an excessive amount of Cleaner F1/mild detergent is used. Use only a small

amount. Wipe off the cleaner completely to leave no residue on the cleaned parts.

ATTENTION

Do not wipe the touch screen with a damp cloth.

Dust on the surface may become stuck between the touch screen and the scanner, causing the touch screen to

malfunction.

Replacing the Consumables

This section explains how to replace the consumables for the scanner.

Consumables and Replacement Cycles

*1: The suggested replacement cycles are guidelines for using A4 (80 g/㎡[20 lb.]) wood-free paper, as these

cycles vary depending on the type of documents scanned.

Consumables need to be replaced periodically. It is recommended that you keep a stock of new consumables and

replace them before it reaches the end of the consumable life. Also, the scanner records the number of sheets scanned

for each consumable (brake roller and pick roller), which allows you to determine when to replace the consumables.

The inside of the ADF becomes very hot when the scanner is being used.

Before you replace the consumables, make sure to turn off the power, unplug the power cable and wait for at least

15 minutes for the inside of the ADF to cool down.

Before replacing the consumables, check the status of each consumable in the following procedure.

(1) Tap in the home screen on the touch panel of the ScanSnap to display the [Settings] screen.

(2) Tap to display the [Maintenance] screen.

(3) Tap [Check consumable status] to display the [Check consumable status] window.

(4) Check the value for [Current Count / Replacement Cycle].

Note that the suggested replacement cycles are guidelines for using A4 (80 g/m2[20 lb.]) wood-free or wood-containing

paper, as these cycles vary depending on the type of documents scanned and how often the scanner is used and

cleaned.

For information on purchasing the consumables, contact the distributor/dealer where you purchased this product. Or,

make an inquiry by referring to the contact information at the Contact for Inquiries section in Safety Precautions

bundled with this product.

Replacing the Brake Roller

Replace the brake roller in following procedure.

(1) Open the ADF top section.

(2) By holding the both ends of the Guide-R-ASSY (brake roller cover), open it in the direction of the arrow.

HINT

Only use the specified consumables.

(3) Lift the BR-Roller-ASSY on the right side, remove the right-side shaft (①), and pull out the left-side shaft from the slot

(②).

(4) Remove the BR-Roller-ASSY from the BR-Shaft-ASSY.

Installation

(1) Insert the protrusion on the BR-Shaft-ASSY into the groove of the BR-Roller-ASSY.

Andere Handbücher für ScanSnap iX1500

Inhaltsverzeichnis

Andere Fujitsu Scanner Handbücher

Fujitsu

Fujitsu fi-6140Z Bedienungsanleitung

Fujitsu

Fujitsu M4099D Handbuch

Fujitsu

Fujitsu FI-4120C Handbuch

Fujitsu

Fujitsu ScanPartner Handbuch

Fujitsu

Fujitsu Scan Snap S1300i Handbuch

Fujitsu

Fujitsu Fi-5110EOX2 - ScanSnap! - Document Scanner Bedienungsanleitung

Fujitsu

Fujitsu FI-5530C2 Referenzhandbuch

Fujitsu

Fujitsu FI-5530C2 Konfigurationshandbuch

Fujitsu

Fujitsu M3097DE Konfigurationshandbuch

Fujitsu

Fujitsu M3099A/G Handbuch

Fujitsu

Fujitsu ScanPartner SP30 Handbuch

Fujitsu

Fujitsu PFU fi-5110C Konfigurationshandbuch

Fujitsu

Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Konfigurationshandbuch

Fujitsu

Fujitsu M4099D Bedienungsanleitung

Fujitsu

Fujitsu FI-4120C Bedienungsanleitung

Fujitsu

Fujitsu fi-680PRB Handbuch

Fujitsu

Fujitsu ScanSnap iX500 Bedienungsanleitung

Fujitsu

Fujitsu Fi-5110EOX2 - ScanSnap! - Document Scanner Referenzhandbuch

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Fujitsu

Fujitsu fi-6670 Series Bedienungsanleitung

Fujitsu

Fujitsu fi-4640S Handbuch

Fujitsu

Fujitsu ScanSnap iScanner fi-6010N Bedienungsanleitung

Fujitsu

Fujitsu FI-7600 Bedienungsanleitung

Fujitsu

Fujitsu TWAIN 32 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung

Visioneer

Visioneer CardReader 100 Kurzanleitung

Rohde & Schwarz

Rohde & Schwarz TSME6 Bedienungsanleitung