Fujitsu SPARC Enterprise M3000 Bedienungsanleitung

Accessing Important Information and Documentation

Before you deploy the SPARC Enterprise M3000 server, check for late breaking information about patches for

firmware and software, and known issues. This information, found in the SPARC Enterprise M3000/M4000/M5000/

M8000/M9000 Servers Product Notes, supersedes the information in other documents. The latest version of SPARC

Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product Notes, SPARC Enterprise M3000 Server Installation Guide,

and other documentation for the M3000 server are available on the following website:

http://www.fujitsu.com/sparcenterprise/manual/

SPARC Enterprise M3000 Server Documentation

System

Planning and

Site Preparation

• SPARC Enterprise M3000 Server Overview Guide

• SPARC Enterprise M3000 Server Site Planning Guide

• SPARC Enterprise Equipment Rack Mounting Guide

System

Installation

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product Notes

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Important Legal and Safety

Information (Printed)

• SPARC Enterprise M3000 Server Safety and Compliance Guide

• SPARC Enterprise M3000 Server Getting Started Guide (This document)

• SPARC Enterprise M3000 Server Installation Guide

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF User’s Guide

SPARC Enterprise M3000

Server

Getting Started Guide

Note – AC power supply model and DC power supply model are available for the M3000 server. The

chapters of each document are written based on AC power supply model. If there is any specific

information on DC power supply model, it is indicated in the appendix “DC Power Supply Model“ of

each document. Be sure to see the appendix when you use DC power supply model.

Installation Steps for SPARC Enterprise M3000 Server

For quick installation and configuration, follow these steps. For more detailed information, see the SPARC

Enterprise M3000 Server Installation Guide.

1. Verify power, air conditioning, and floor area requirements.

Prepare adequate power equipment according to the type of power supply to your server model. For

details, see the SPARC Enterprise M3000 Server Site Planning Guide.

2. Prepare items required for installing the server.

3. Check the delivered items against the “LIST OF ATTACHMENT” that came with the server.

4. Set up the equipment rack and mount the M3000 server.

See the SPARC Enterprise Equipment Rack Mounting Guide.

Caution – Make sure that the power source circuit breaker is in the OFF position before connecting

the power cords.

5. Connect the power cords to the power supply units on the rear panel of the server.

Make sure that each power cord is connected to the server and secured with a cord clamp.

6. Connect the power cords to the power supply system.

The requirements for connecting power cords vary depending on the type of power supply to your server

model. For details, see the SPARC Enterprise M3000 Server Installation Guide.

■AC power supply model

The AC power supply model of the M3000 server is shipped with two grounding-type (three-wire)

power cords. Always connect the power cords into grounded power outlets.

■DC power supply model

The DC power supply model of the M3000 server is shipped with two DC power cords. Since these DC

power cords have a connector only for the server end, a terminal matching the DC power supply

equipment will need to be attached to the DC power supply end of the cord. Moreover, the power

supply equipment must be correctly grounded.

Administration • SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product Notes

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF User’s Guide

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF Reference Manual

Repair and

Troubleshooting

• SPARC Enterprise M3000 Server Service Manual

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide

Globalization For SPARC Enterprise M3000 server, the documents of localized versions will be offered on the

website:

http://www.fujitsu.com/sparcenterprise/manual/

FIGURE 1 Rear Panel of the Server

7. Use the RS232C cable (serial cable, RJ-45 to DB-9) supplied with the server in the Accessory Kit, and

connect the administration console to the serial port (see FIGURE 1, #3) on the rear panel of the server.

You can use any of the following devices with a DB-9 serial port as the administration console: ASCII

terminal, workstation, terminal server (or a patch panel connected to a terminal server), personal

computer.

Caution – Be careful not to connect a LAN cable to the serial port.

Location Number Component

1 Power supply unit

2PCIeslot

3 Serial port (for XSCF)

4 LAN port (for XSCF)

5 Gigabit Ethernet (GbE) port (for OS)

1 2 34

AC Power Supply Model

1234

DC Power Supply Model

8. The following steps will log in to the XSCF Shell and initialize the XSCF settings.

XSCF is a system control facility to set up and control the server. To initialize the XSCF settings, use the

XSCF default user account.

a. Set the mode switch on the operator panel to the Service mode ( ).

The key for the mode switch is supplied with the server.

FIGURE 2 Operator Panel

b. Turn the power source circuit breaker to "ON".

After the power is turned on, the server starts the XSCF initialization that can take up to 5 or more

minutes. When the initialization completes, the XSCF STANDBY LED ( ) on the operator panel

lights.

c. After the XSCF initialization completes, enter default at the login prompt.

d. Operate the mode switch within one minute according to the messages to change the mode switch.

A login authentication timeout will occur after one minute.

Location Number Name

1 POWER LED

2 XSCF STANDBY LED

3 CHECK LED

4 Power button

5 Mode switch (Key switch)

Change the panel mode switch to Locked and press return...

Leave it in that position for at least 5 seconds.

Change the panel mode switch to Service, and press return...

e. Confirm that the XSCF Shell prompt is displayed on the administration console.

f. Initialize the XSCF settings. The following are the required settings for installation.

For details on the setting procedure, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000

Servers XSCF User’s Guide.

g. Log in to the XSCF Shell with the user account and password that were set in Step f.

9. The following steps will power on the server.

a. Confirm that the mode switch on the operator panel is set to the Service mode ( ).

b. From the XSCF Shell, enter the following console command:

This switches you from the XSCF Shell to the domain console.

c. Confirm that the XSCF STANDBY LED ( ) on the operator panel is on.

d. Push the Power button ( ) on the operator panel to power on the server.

The server starts and begins a self-diagnosis. Confirm that no error messages are displayed on the

administration console during the boot process.

e. Confirm that the POWER LED ( ) on the operator panel is turned on.

f. Confirm that ok prompt is displayed on the domain console.

The ok prompt is displayed after the self-diagnosis completes.

XSCF>

Settings Command

Registration of an XSCF user account, password, and user privileges

Registration of a user account of a field engineer (FE) (for maintenance)

adduser, password,

setprivileges

Date and time settings setdate, settimezone

Confirmation of the XSCF host public key showssh

SSH/telnet settings setssh, settelnet

Network interface, routing, and DNS-related settings *

* To apply the settings, the XSCF unit must be reset with the applynetwork and rebootxscf commands.

setnetwork,setroute,

setnameserver etc.

Domain-SP Communication Protocol (DSCP) settings †

† To apply the settings, the XSCF unit must be reset with the rebootxscf commands.

setdscp

Altitude administration setting ‡

‡ To apply changes made with the setdualpowerfeed command, power to the server must be completely disconnected and then

reconnected (all power cords must be disconnected and then reconnected). Wait at least 30 seconds before reconnecting the power cords to

the server.

setaltitude

Dual power feed option setting setdualpowerfeed

XSCF> console -d 0

Connect to DomainID 0?[y|n] :y

g. Press the Enter key, and then press the "#" and “.“(period) keys.

This switches you from the domain console to the XSCF Shell.

h. From the XSCF Shell, execute the fmdump command or showlogs command, and confirm that no

errors are found.

10. Connect the system control network to a LAN port (see FIGURE 1, #4) on the rear panel of the server with

an Ethernet cable.

The system control network is a network that connects the XSCF to the administration console for the

system administrator's use. This connection will replace the temporary connection between the

administration console and the serial port.

The LAN ports conform to IEEE 802.3i and IEEE 802.3u. However, only the auto-negotiation mode can be

used for negotiation. The fixed mode cannot be used.

11. Verify the hardware configuration by using the following commands on the administration console

connected to the system control network.

To switch from the XSCF console to the ok prompt, enter the console -d 0 command. To switch from

the ok prompt to the XSCF console, press the enter key, and then press the "#" and "." (period) keys.

12. Install additional hardware or peripheral devices. If not needed, proceed to the Step 13.

For details on how to add optional devices, such as additional memory or an additional PCIe card, see the

SPARC Enterprise M3000 Server Service Manual. To add an additional storage device or other peripheral

device, see the manual supplied with the device.

13. The following steps will connect the domain to the user network. If you isolate the domain from the

network, proceed to the Step 14.

The user network is a network which enables users to access the domain.

a. Connect one end of an Ethernet cable to a GbE port (for the OS) (see FIGURE 1, #5) on the rear panel

of the server.

You can connect the Ethernet cable to a GbE port (for the OS) or to the LAN port on a LAN card

mounted in a PCIe slot (see FIGURE 1, #2).

b. Connect the other end of the Ethernet cable to the customer’s network environment.

Command Prompt Description

showhardconf XSCF Shell All the components installed in the server and their statuses are displayed.

Confirm that no asterisk (*) is displayed in front of any FRUs.

showhardconf -u XSCF Shell Check the number of FRUs mounted on the server against the “PRODUCT

TEST RECORD“ that came with the server.

probe-scsi-all ok Prompt Confirm that the CD-RW/DVD-RW drive unit and hard disk drive

installed in the server are recognized.

show-devs ok Prompt Confirm that each installed PCIe card is recognized.

14. The following steps will boot the Oracle Solaris Operating System.

The Oracle Solaris OS is preinstalled in the slot 0 of the hard disk drives.

a. From the ok prompt of the domain console, execute the boot command.

b. After the login prompt is displayed, log in with root account.

15. Confirm hardware operations and device connection statuses by using the Oracle VTS software.

The Oracle VTS software is included in the Oracle Solaris OS. For details, see the Oracle VTS User’s Guide.

16. Make the initial settings for the domain.

For details, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide.

ok boot

Manual Code: C120-E536-04EN

March 2012, Revision A

FUJITSU LIMITED

Documentation Feedback

If you have any comments or requests regarding this document, or if you find any unclear statements in the

document, please state your points specifically on the form at the following website:

http://www.fujitsu.com/global/contact/computing/sparce_index.html

Andere Handbücher für SPARC Enterprise M3000

Inhaltsverzeichnis

Andere Fujitsu Server Handbücher

Fujitsu

Fujitsu PRIMERGY TX140 S1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX150 S6 Leitfaden

Fujitsu

Fujitsu PRIMEQUEST 1000 Series Bedienungsanleitung

Fujitsu

Fujitsu BS2000 SE Series Bedienungsanleitung

Fujitsu

Fujitsu FUTRO S930 Bedienungsanleitung

Fujitsu

Fujitsu Primergy TX300 S4 Kurzanleitung

Fujitsu

Fujitsu SPARC Enterprise M3000 Service-Handbuch

Fujitsu

Fujitsu PRIMERGY TX1330 M2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX120 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY H200 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX2540 M1 Bedienungsanleitung

Fujitsu

Fujitsu M10 Series Technisches Handbuch

Fujitsu

Fujitsu PRIMERGY RX800 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX300 S5 Bedienungsanleitung

Fujitsu

Fujitsu S140 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX1330 M3 Bedienungsanleitung

Fujitsu

Fujitsu BS2000 SE Series Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX500 S7 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY RX220 Bedienungsanleitung

Fujitsu

Fujitsu PRIMEQUEST 2000 Series Montageanleitung

Fujitsu

Fujitsu M10 Series Service-Handbuch

Fujitsu

Fujitsu PRIMERGY TX150 S2 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY TX1320 M1 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX924 S3 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung