Fujitsu MHW2040AT - Mobile 40 GB Hard Drive Bedienungsanleitung

CHAPTER 3 Installation Conditions

3.1 Dimensions

3.2 Mounting

3.3 Cable Connections

3.4 Jumper Settings

This chapter gives the external dimensions, installation conditions, surface

temperature conditions, cable connections, and switch settings of the hard disk

drives.

For information about handling this hard disk drive and the system installation

procedure, refer to the following Integration Guide.

C141-E144

C141-E250 3-1

Installation Conditions

3.1 Dimensions

Figure 3.1 illustrates the dimensions of the disk drive and positions of the

mounting screw holes. All dimensions are in mm.

Figure 3.1 Dimensions

3-2 C141-E250

3.2 Mounting

For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION

GUIDANCE (C141-E144)."

(1) Orientation

The disk drives can be mounted in any direction.

(2) Frame

The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame

is connected to SG.

Use M3 screw for the mounting screw and the screw length should

satisfy the specification in Figure 3.2.

The tightening torque must be 0.49N•m (5kgf•cm).

When attaching the HDD to the system frame, do not allow the

system frame to touch parts (cover and base) other than parts to

which the HDD is attached.

(3) Limitation of mounting

Note) These dimensions are recommended values; if it is not possible to satisfy

them, contact us.

Side surface

mounting

2.5 2.5

Bottom surface mounting

2.5

DE 2.5

2 B

PCA

A Frame of system

cabinet

Frame of system

cabinet

3.0 or less Screw

Screw 3.0 or less

Details of A

Details of B

Figure 3.2 Mounting frame structure

C141-E250 3-3

Installation Conditions

Because of breather hole mounted to the HDD, do not allow this to

close during mounting.

Locating of breather hole is shown as Figure 3.3.

For breather hole of Figure 3.3, at least, do not allow its around φ 3

to block.

Figure 3.3 Location of breather

3-4 C141-E250

3.2 Mounting

C141-E250 3-5

(4) Ambient temperature

The temperature conditions for a disk drive mounted in a cabinet refer to the

ambient temperature at a point 3 cm from the disk drive. The ambient

temperature must satisfy the temperature conditions described in Section 1.4, and

the airflow must be considered to prevent the DE surface temperature from

exceeding 60 °C.

Provide air circulation in the cabinet such that the PCA side, in particular,

receives sufficient cooling. To check the cooling efficiency, measure the surface

temperatures of the DE. Regardless of the ambient temperature, this surface

temperature must meet the standards listed in Table 3.1. Figure 3.4 shows the

temperature measurement point.

Figure 3.4 Surface temperature measurement points

Table 3.1 Surface temperature measurement points and standard values

No. Measurement point Temperature

1 DE cover 60 °C max

Installation Conditions

(5) Service area

Figure 3.5 shows how the drive must be accessed (service areas) during and after

installation.

Mounting screw hole

Cable connection

Figure 3.5 Service area

Data corruption: Avoid mounting the disk drive near strong

magnetic sources such as loud speakers. Ensure that the disk drive

is not affected by external magnetic fields.

Damage: Do not press the cover of the disk drive. Pressing it too

hard, the cover and the spindle motor contact, which may cause

damage to the disk drive.

Static: When handling the device, disconnect the body ground

(500 kΩor greater). Do not touch the printed circuit board, but hold

it by the edges.

(6) Handling cautions

Please keep the following cautions, and handle the HDD under the safety

environment.

3-6 C141-E250

3.2 Mounting

- General notes

ESD mat

Shock absorbin

mat

Wrist strap

Use the Wrist stra

. Place the shock absorbing mat on the

operation table, and place ESD mat on it.

Do not hit HDD each other. Do not stack when carr

Do not

lace HDD verticall

to avoid fallin

down. Do not dro

Figure 3.6 Handling cautions

- Installation

(1) Please use the driver of a low impact when you use an electric driver.

HDD is occasionally damaged by the impact of the driver.

(2) Please observe the tightening torque of the screw strictly.

M3 ······· 0.49N•m (5 kgf•cm).

- Recommended equipments

Contents Model Maker

Wrist strap JX-1200-3056-8 SUMITOMO 3MESD

ESD mat SKY-8A (Color Seiden Mat) Achilles

Shock Low shock driver SS-6500 HIOS

C141-E250 3-7

Installation Conditions

3.3 Cable Connections

3.3.1 Device connector

The disk drive has the connectors and terminals listed below for connecting

external devices. Figure 3.7 shows the locations of these connectors and terminals.

Connector,

setting pins

PCA

Figure 3.7 Connector locations

3-8 C141-E250

3.3 Cable Connections

3.3.2 Cable connector specifications

Table 3.2 lists the recommended specifications for the cable connectors.

Table 3.2 Cable connector specifications

Name Model Manufacturer

ATA interface and power

supply cable (44-pin type)

Cable socket

(44-pin type)

89361-144 FCI

For the host interface cable, use a ribbon cable. A twisted cable or a

cable with wires that have become separated from the ribbon may

cause crosstalk between signal lines. This is because the interface is

designed for ribbon cables and not for cables carrying differential

signals.

3.3.3 Device connection

Figure 3.8 shows how to connect the devices.

Host system

Power supply

Disk Drive #0

Disk Drive #1

ATA-cable

Power supply cable

Figure 3.8 Cable connections

Damage: Interface cable connection

Take note of the following precaution about plugging an interface

cable (socket) into the interface connector of the disk drive and

plugging the connector into a host receptacle:

−When plugging together the disk drive interface connector and

the host receptacle or interface cable connector (socket), do not

apply more than 10 kgf of force in the connection direction once

they are snugly and securely in position.

C141-E250 3-9

Installation Conditions

3.3.4 Power supply connector (CN1)

Figure 3.9 shows the pin assignment of the power supply connector (CN1).

Figure 3.9 Power supply connector pins (CN1)

3.4 Jumper Settings

3.4.1 Location of setting jumpers

Figure 3.10 shows the location of the jumpers to select drive configuration and

functions.

Figure 3.10 Jumper location

3-10 C141-E250

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Lagerung Handbücher

Fujitsu

Fujitsu ETERNUS DX100 S3 Bedienungsanleitung

Fujitsu

Fujitsu GRANPOWER 5000 GP5-HDH461 Bedienungsanleitung

Fujitsu

Fujitsu MAM3184MC/MP Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 S4 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS4000' ETERNUS8000 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT20 S2 Bedienungsanleitung

Fujitsu

Fujitsu MHU2100AT Bedienungsanleitung

Fujitsu

Fujitsu MAP3147NP Bedienungsanleitung

Fujitsu

Fujitsu MPC3096AT - Desktop 9.7 GB Hard Drive Bedienungsanleitung

Fujitsu

Fujitsu MBA3073 SERIES Bedienungsanleitung

Fujitsu

Fujitsu Eternus DX80 S2 Bedienungsanleitung

Fujitsu

Fujitsu MHN2100AT - Mobile 10 GB Hard Drive Bedienungsanleitung

Fujitsu

Fujitsu M2301B Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 S2 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS AX Series Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 S3 Installationsanleitung

Fujitsu

Fujitsu ETERNUS LT260 Bedienungsanleitung

Fujitsu

Fujitsu eternus af Bedienungsanleitung

Fujitsu

Fujitsu MHC2032AT Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS Bedienungsanleitung

Fujitsu

Fujitsu MHZ2080BJ Bedienungsanleitung

Fujitsu

Fujitsu Citrix XenServer Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX S2, ETERNUS DX S3, ETERNUS DX S4, ETERNUS... Bedienungsanleitung

Fujitsu

Fujitsu MHV2200BT Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung