FUTABA 3PDF Bedienungsanleitung

1M23N02102

3PDF

Instruction

Manual

ForCar'sandBoat's

3ChannelDigitalProportionalR/CSystem

Thank you for purchasing the Futaba 3PDF.

Prior to operating your 3PDF, please read this manual thoroughly and use

your system in a safe manner.

After reading this manual store it in a safe place.

See the glossary on page (P36) for the definition’s of the special terms used in

this manual.

Application, Export and Reconstruction

1. Use this product in surface models only.

The product described in this manual is subject to regulations of the Ministry of

Radio/Telecommunications and is restricted under Japanese law to such pur-

poses.

2. Exportation Precautions

(a) When this product is exported from Japan, its use is to be approved by the

Radio Law of the country of the destination.

(b) Use of this product with other than models may be restricted by Export and

Trade Control Regulations. An application for export approval must be submit-

ted.

3. Modification, adjustment and replacement of parts.

Futaba is not responsible for unauthorized modification, adjustment and re-

placement of parts of this product.

THE FOLLOWING STATEMENT APPLIES TO THE

RECEIVER (FOR U.S.A.)

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions.

(1) This devise may not cause harmful interference, and

(2) This devise must accept any interference received, including interference

that may cause undesired operation.

-No part of this manual may be reproduced in any form without prior permission.

-The contents of this manual are subject to change without prior notice.

-This manual has been carefully written, please write to Futaba if you feel that any corrections or clarifica-

tions should be made.

-Futaba is not responsible for the use of this product.

-Futaba is an registered trademark of Futaba Corporation.

ダ

イ

レ

ク

ト

モ

ー

ド

機

能

3PDF

Table of Contens

Reference

Ratings 34

Optional parts 34

Troubleshooting 35

Glossary 36

When requesting repair 37

Description of Functions

Steering Trim 20

Throttle Trim 21

Servo Reverse 22

Steering ATV 23

Throttle ATV 24

Steering D/R 25

Throttle ATL 26

Steering Exponential 27

Throttle Exponential 28

Model Select 29

Model Name 30

Lever Function Select 31

Channel 3 Function Selection 32

CH3 Position Setting 33

Assembly

Receiver and Servo Connections14

Assembly Safety Precautions 15

Preparations Prior to Setting Trans-

mitter 16

E.S.C. MC210CB Adjustment 17

For your safety as well as

that of others.

Explanation of Symbols 2

Operation Precautions 2

Nicad Battery Handling Precautions

Other Precautions 4

Storage and Disposal Precautions

Prior to Operation

Features 6

Set Contents 7

Nomenclature / Handling 8

Digital Trim Operating Instructions

D/R ATL CH3 LeverOperating In-

structions 11

Display / Key Operation 12

Warning Displays 13

Precautions when turning the power

switches off and on. 13

Function Map

Function Mode Group 18

System Mode Group 18

Direct Mode Group 19

For your safety

as well as that

of others.

Prior to

Operation

Assembly

Function

Map

Description

Functions

Reference

For your safety as well as that of others.

3PDF

For your safety as well as that of others.

Use this product in a safe manner. Please observe the following safety precautions at

all times. Explanation of Symbols

The parts of this manual indicated by the following symbols are extremely important

and must be observed.

DANGER Indicates a procedure which could lead to a dangerous situ-

ation and may cause death or serious injury if ignored and

not performed properly.

Warning Indicates procedures which may lead to dangerous situa-

tions and could cause death or serious injury as well as su-

perficial injury and physical damage.

Caution Indicates procedures that may not cause serious injury, but

could lead to physical damage.

Symbols: ; Prohibited ; Mandatory

Symbols Explanation

Operation Precautions

Warning

Prohibited Procedures

Do not operate two or more models

on the same frequency at the same

time.

Operating two or more models at same time on the

same frequency will cause interference and loss of

control of both models.

AM, FM (PPM) and PCM are different methods

of modulation. Nonetheless the same frequency

can not be used at the same point in time, regard-

less of the signal format.

Do not operate outdoors on rainy

days , run through puddles of water or

when visibility is limited.

Should any type of moisture (water or snow) enter any

compoent of the system, erratic opreation and loss of

control may occur.

Do not operate in the following

places.

-Near other sites where other radio control

activity may occur.

-Near people or roads.

-On any pond when rowboats are present.

-Near high tension power lines or communi-

cation broadcasting antennas.

Interference could cause loss of control . Improper in-

stallation of your Radio Control System in your model

could result in serious injury.

Do not operate this R/C system when

you are tired, not feeling well or under

the influence of alcohol or drugs.

Your judgment is impaired and could result in a dan-

gerous situation that may cause serious injury to

yourself as well as others.

For your safety as well as that of others.

Mandatory Procedures

Extend the transmit-

ter antenna to its full

length.

If the transmitter antenna is not

fully extended the operating

range of the radio will be re-

duced.

Item Check

Check the transmitter antenna to be

sure it is not loose.

If the transmitter antenna works loose, or is discon-

nected while the model is running signal transmission

will be lost. This will cause you to lose control of the

model..

Caution Prohibited Procedures

Mandatory Procedures

Always perform a operating range

check prior to use.

Problems with the radio control system as well as im-

proper installation in a model could cause loss of con-

trol.

(Simple range test method)

Have a friend hold the model, or clamp it down or

place it where the wheels or prop can not come in

contact with any object. Walk away and check to

see if the servos follow the movement of the con-

trols on the transmitter. Should you notice any ab-

normal operation, Do not operate the model. Also

check to be sure the model memory matches the

model in use.

When changing the frequency, be

sure to always use genuine Futaba

crystal sets (transmitter and receiver)

as specified in this manual. (Chang-

ing the frequency crystals in systems

on 75MHz is illegal per FCC regula-

tions)

If other brands of crystals are

used the system may not op-

erate or the operating range

may be reduced.Loss of con-

trol will occur .

Do not touch the engine, motor, speed control or any part of

the model that will generate heat while the model is operating

or immediately after its use.

These parts may be very hot and can cause serious burns.

Turning on the power switches.

Always check the throttle trigger on the

transmitter to be sure it is at the neutral

position.

1. Turn on the transmitter power switch.

2. Turn on the receiver or speed control

power switch.

Turning off the power switches

Always be sure the engine is not

running or the motor is stopped.

1. Turn off the receiver or speed control power switch.

2. Then turn off the transmitter power switch.

If the power switches are turned off in the opposite

order the model may unexpectedly run out of control

and cause a very dangerous situation.

When making adjustments to

the model do so with the en-

gine not running or the motor

disconnected.

You may unexpectedly lose control and

create a dangerous situation.

When operating your model

always display a frequency

flag on your transmitter an-

tenna.

When you change the frequency, also

change the flag to the corresponding chan-

nel.

Extend to

full length





Tx Rx

Tx: Transmitter

Rx: Receiver

Use genuine Futaba

crystal sets only.

B/C

FP-R113F

Power ON

Power OFF

For your safety as well as that of others.

Nicad Battery Handling Precautions

(Only when Nicad batteries are used)

Warning Mandatory Procedures

Always check to be sure your batter-

ies have been charged prior to oper-

ating the model.

Should the battery go dead while the model is operat-

ing loss of control will occur and create a very danger-

ous situation.

To recharge the transmitter Nicad ,

use the special charger made for this

purpose.

Overcharging could cause the Nicad battery to over-

heat, leak or explode. This may lead to fire, burns,

loss of sight and many other type's of injuries.

Caution Prohibited Items

Do not use commercial AA size Nicad

batteries.

Quick charging may cause the

battery contacts to overheat and

damage the battery holder.

Do not short circuit the Nicad battery

terminals.

Causing a short circuit across the battery terminals

may cause abnormal heating, fire and burns.

Do not drop the Nicad battery or ex-

pose it to strong shocks or vibrations.

The battery may short circuit and overheat, electrolyte

may leak out and cause burns or chemical damage.

Other Precautions

Caution

Prohibited Procedures

Do not expose plastic parts to fuel,

motor spray, waste oil or exhaust.

The fuel, motor spray, waste oil and exhaust will pen-

etrate and damage the plastic.

Always use only genuine Futaba

transmitters, receivers, servos, FET

amps (electronic speed

controls),Nicad batteries and other

optional accessories.

Futaba will not be responsible for problems caused by

the use of other than Futaba genuine parts. Use the

parts specified in the instruction manual and catalog.

Mandatory Procedures

When the model is not being used,

always remove or disconnect the

Nicad battery .

Should the battery be left connected this could create

a dangerous situation if someone accidentally turns

on the receiver power switch. Loss of control would

occur.

Special

Charger

Nicad AA size

batteries.

Use

prohibited

Shock

Prohibited

For your safety as well as that of others.

Storage and Disposal Precautions

Warning

Prohibited Procedures

Do not leave the radio system or

models within the reach of small chil-

dren.

A small child may accidentally operate the system,

this could cause a dangerous situation and injuries.

Nicad batteries can be very dangerous when mis-

handled and cause chemical damage.

Do not throw Nicad batteries into a

fire. Do not expose Nicad batteries to

extreme heat. Also do not disas-

semble or modify a Nicad battery

pack.

Overheating and breakage will cause the electrolyte

to leak from the cells and cause skin burns, loss of

sight as well as other injuries.

Mandatory Procedures

When the system will not be used for

any length of time store the system

with batteries in a discharged state.

Be sure to recharge the batteries prior

to the next time the system is used.

If the batteries are repeatedly recharged in a slightly

discharged state the memory effect of the nicad bat-

tery may considerably reduce the capacity . A reduc-

tion in operating time will occur even when the batter-

ies are charged for the recommended time.

The electrolyte in Nicad batteries is a strong alkali. Should you get even the

smallest amount of the electrolyte in your eyes, DO NOT RUB, wash immedi-

ately with water, seek medical attention at once. The electrolyte can cause blind-

ness. If electrolyte comes in contact with your skin or clothes, wash with water

immediately.

Caution

Prohibited Procedures

Do not store your R/C system in the

following places.

- Where it is extremely hot or cold.

- Where the system will be exposed to direct

sunlight.

- Where the humidity is high.

-Where vibration is prevalent.

-Where dust is prevalent.

-Where the system would be exposed to

steam and condensation.

Storing your R/C system under adverse conditions

could cause deformation and numerous problems

with opreation.

Mandatory Procedure

If the system will not be used for a

long period of time remove the batter-

ies from the transmitter and model

and store in a cool dry place.

If the batteries are left in the transmitter electrolyte

may leak and damage the transmitter. This applies to

the model also, remove the batteries from it also to

prevent damage.

A used Nicad battery is valuable resource. Insulate the battery terminals and

dispose the battery by taking it to a battery recycling center.

Prior to operation

3PDF

Prior to operation

Features

-Multiple Model Memory (3 Models)

A model name can be assigned each memory using six alphabetic,

numeric and symbolic characters. (P30)

Digital Trim Memory will recall all trim settings. As you go from

model to model memory all trim settings will not have to be reset.

-Large LCD Display

All program information is displayed on a 8 character 2 line dis-

play. The large display is easy to read.

-The third channel can be used to match your

application in specialty models.

The third channel can be used in five operation modes.(P32)

-Digital Trim

Digital trim will allow positive and quick settings to be made.

-Lever Function Selection (P31)

This function applies to D/R, ATL and 3rd channel levers.. Since

they are digital, when you change the model memory these will not

require you to readjust the settings . They will be where they were

the last time that model memory was used.

-New Lightweight and Balanced Design

-Trigger Brake Stop (Mechanical ATL) (P8)

-Body Rest can be used (Option)

-Servo Reverse Function (P22) / Steering

ATV Function (P23) / Steering D/R function

(P25) / Throttle ATV Function (P24) / Throttle

ATL Function (P26)

Prior to operation

T3PDF (x1)

R113F (x1)

S3003 (x2 )

MC210CB (x1)

CSW-GS (x1)

or (none)

R2-BSS-B (x1)

or (none)

S3003 (x1)

Set Contents

After opening the container, check the contents for the following items. The contents

will vary with the system purchased.

Transmitter

/ Receiver System with

2 servos System with

1 MC210CB

Transmitter

Receiver

Servo

E.S.C.

Switch

Battery

Holder

Miscellaneous

Servo mounting hardware and servo horns

Mini Screwdriver

-Should any item be missing or you are uncertian of the contents of the system, please

contact the dealer where the system was purchased.

Prior to operation

Nomemclature / Handling

Transmitter T3PDF (Front)

* In the figure above the levers are shown in the neutral position.

Charging Jack

This jack is used to charge Nicad bat-

tery when used.

Caution

Never charge a dry cell type (Non-

Nicad) battery.

Charging a non nicad type battery may damage the

transmitter, and could cause the battery electrolyte

to leak and cause additional damage.

Mechanical ATL

The throttle trigger travel can be ad-

justed to limit the brake stroke.

-Adjustment Method

When the screw is turned clockwise

the brake stroke will become shorter.

When the screw is turned counter

clockwise the stroke becomes longer

as shown in the figure above.

MODE RESET

SELECT

MULTI FUNCTION DISPLAY

DOT MATRIX

CHARGE

POWER

DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM

Antenna

Steering Trim

Steering Wheel

Channel 3

Lever

Edit Keys

Mechanical ATL

Adjustment Hole

Throttle Trigger

Grip Handle

Body Rest

Mounting Hole

Steering D/R Lever

Throttle ATL Lever

Power Switch

Charging Jack

LCD

Screen

Power LED

Throttle Trim

Inhaltsverzeichnis

Andere FUTABA Fernbedienung Handbücher

FUTABA

FUTABA FP-3FN Bedienungsanleitung

FUTABA

FUTABA FX10 Montage- und Bedienungsanleitung

FUTABA

FUTABA T7PXR Technisches Handbuch

FUTABA

FUTABA 8FG Bedienungsanleitung

FUTABA

FUTABA 12FG Bedienungsanleitung

FUTABA

FUTABA FX-36 Bedienungsanleitung

FUTABA

FUTABA R7314SB Bedienungsanleitung

FUTABA

FUTABA FP-8SSHP Bedienungsanleitung

FUTABA

FUTABA 4PK-2.4GHZ Bedienungsanleitung

FUTABA

FUTABA Magnum Sport FP-S148 Bedienungsanleitung

FUTABA

FUTABA FP-4DN Bedienungsanleitung

FUTABA

FUTABA T18SZ Bedienungsanleitung

FUTABA

FUTABA 9z Installationsanleitung

FUTABA

FUTABA R334SBS Technisches Handbuch

FUTABA

FUTABA 6EXAP Bedienungsanleitung

FUTABA

FUTABA 4EXA Bedienungsanleitung

FUTABA

FUTABA 3PKS Bedienungsanleitung

FUTABA

FUTABA FP-3EG Bedienungsanleitung

FUTABA

FUTABA 8FG Bedienungsanleitung

FUTABA

FUTABA 7C - Bedienungsanleitung

FUTABA

FUTABA 6k Bedienungsanleitung

FUTABA

FUTABA FP-3UCP Bedienungsanleitung

FUTABA

FUTABA 7C-2.4GHz Bedienungsanleitung

FUTABA

FUTABA 12Z Series Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung