Galvin Engineering BS Capstan SBA Merkblatt

Product Installation Guidelines

Document No.: 001.00.30.14

Version 1, 4 October 2022, Page 1of 4

CP-BS Wall/Pillar/Bib/Basin SBA

PRODUCT CODES:

- 32728 (BS Capstan SBA)

- 48751 (BS Stirling SBA)

- 50015 (Vandal Resistant CP-BS SBA)

- 35793 (Ezy-Twist CP-BS SBA)

SPECIFICATIONS

−The main body is made of solid dezincification resistant (DR) brass rod, with a DR brass fixed outlet.

IMPORTANT: All taps are tested in accordance with AS/NZS 3718 and leave our premises in good working

order.

TECHNICAL DATA

Inlet

G 5/8”BSP

Outlet

N/A

Headwork

32728

Ceramic Disc

48751, 50015

Jumper Valve

35793

Cam Action

Working Pressure Range (kPa)

Min

Max

500

Working Temperature (°C)

Min

Max

Nominal Flow Rate (LPM)

N/A

Finish

Brass

NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without notice.

TOOLS REQUIRED

−Spanner and hex key

−Thread tape

Product Installation Guidelines

Version 1, 4 October 2022, Page 2of 4

INSTALLATION

IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions and in

accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply

conditions must also comply to the applicable national and/or state standards. Failing to comply with these provisions

shall void the product warranty and may affect the performance of the product.

Note: (Illustrations are for representation of installation only and is not limited for use to these components)

1. Remove Handle

−Prior to installation turn off the water supply.

−Remove the handle assembly. To prevent

damage, carefully pry off plastic indicator from

the handle. (Use a small flat bladed screwdriver

if necessary).

2. Replace spindle assembly

−Unscrew the head part from the threaded sleeve

using a 17mm spanner.

−Check seat inside tap body for pitting or damage.

Re-seat if necessary

3. Refit new head part

-Refit new head part into tap body.

Note: do not tighten cartridge using the handle

as this will result in damage to the cartridge

4. Reassemble Handle

-Refit adaptor and reassemble handle by reversing

step 1.

-When installation is complete, slowly open water

supply and inspect for leaks.

New ceramic head

New head part

Product Installation Guidelines

Version 1, 4 October 2022, Page 3of 4

TROUBLESHOOTING

PROBLEM

CAUSE

RECTIFICATION

Taps are dripping water

Ceramic discs are worn or damaged

Remove and inspect SBA. Remove

debris and/or replace SBA if

damaged.

Tap seat is damaged

Refurbish tap seat using a reseating

tool.

Water is not flowing from tap

Water is turned off

Turn on water

Ceramic discs are worn or damaged

Remove and inspect SBA. Remove

debris and/or replace SBA if

damaged.

Spindle is difficult to turn

Ceramic discs are worn or damaged

Remove and inspect SBA. Remove

debris and/or replace SBA if

damaged.

Handle is loose

Screw has come loose

Tighten handle screw

Product Installation Guidelines

Version 1, 29 August 2022, Page 4of 4

WARRANTY

The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.

With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin

Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not limited

to the implied warranties of merchantability and fitness for a particular purpose.

Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from

www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from

operational defects in workmanship and materials for the warranty period as shown on the schedule in the

manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective products

manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s warranty are

complied with.

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for

breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or

consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property

which is damaged if this product does not work properly, other costs resulting from labour charges, delays,

vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical,

electrical or any other circumstances over which Galvin Engineering has no control. This warranty shall be

invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the

product.

Dieses Handbuch passt für folgende Modelle

Andere Galvin Engineering Sanitärprodukte Handbücher

Galvin Engineering

Galvin Engineering Capstan 175.91.00.03 Bedienungsanleitung

Galvin Engineering

Galvin Engineering WaterMark 46638 Merkblatt

Galvin Engineering

Galvin Engineering CliniLever TM-SNKGX Merkblatt

Galvin Engineering

Galvin Engineering Haws GalvinSafe Axion 8100-A Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink Lead Safe 170.50.14.00 Bedienungsanleitung

Galvin Engineering

Galvin Engineering TCWBC150C Bedienungsanleitung

Galvin Engineering

Galvin Engineering CliniLever TCBTC80CC Bedienungsanleitung

Galvin Engineering

Galvin Engineering Ezy-Drink Lead Safe SS316 Merkblatt

Galvin Engineering

Galvin Engineering CliniLever CP-BS Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink CP Lead Safe 2 in 1 Bottle Filler & Bubbler Hob... Merkblatt

Galvin Engineering

Galvin Engineering GalvinAssist CP Bedienungsanleitung

Galvin Engineering

Galvin Engineering Ezy-Drink 316 TDBFXEB Merkblatt

Galvin Engineering

Galvin Engineering CliniMix Lead Safe 100.00.71.00 Merkblatt

Galvin Engineering

Galvin Engineering GalvinSafe 190.42.11.90 Merkblatt

Galvin Engineering

Galvin Engineering GalvinSafe 190.41.12.12 Merkblatt

Galvin Engineering

Galvin Engineering Assist 41978CP Merkblatt

Galvin Engineering

Galvin Engineering 656512 Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Wash TF81HJS Merkblatt

Galvin Engineering

Galvin Engineering Safe-Cell 50150 Merkblatt

Galvin Engineering

Galvin Engineering CliniMix CP-BS WM-TMVPMB Merkblatt

Galvin Engineering

Galvin Engineering CliniLever TCWSC150C Merkblatt

Galvin Engineering

Galvin Engineering Ezy-Drink TD25XEB Bedienungsanleitung

Galvin Engineering

Galvin Engineering Ezy-Push CP-BS Lead Safe Bedienungsanleitung

Galvin Engineering

Galvin Engineering CliniMix WM-PMSKIT Merkblatt

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

Kohler

Kohler K-6228 Montageanleitung

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Bedienungsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Fortis

Fortis MILANO 78211JS Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Moen

Moen 5922 Series Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung