GASLOCK Indy-Cator Bedienungsanleitung
Digital Gear Display
Operating Instructions
2
Table of Contents
Page 3 .................................................... About INDY-CATOR
Page 4 .................................................... Package content
Page 5 .................................................... Gear lever knob installation
Page 6 .................................................... Programming
Page 8 .................................................... Troubleshooting
3
About INDY-CATOR
First, we would like to explain to you the function
of the digital gear display:
It works according to the principle of forming the
difference between two position sensors. As a
result, the selected transmission is displayed for
you. The electronic system recognises even the
smallest changes of positions of the gear lever
knob. It works completely independently of the
vehicle transmission. Only if a position change is
safely recognised as a transmission change will
the display change.
This may take 1 - 1.5 s.
This transmission display is to serve as an aid.
We assume no warranty for correctness of the
display.
If the transmissions are not displayed correctly
for some reason, please repeat programming
with the motor/gear at operational temperature.
Depending on vehicle type and
gear position, extreme vehicle acceleration
may lead to short-term reading changes on the
display. This is based on the physical characteri-
stics of the sensors and does not constitute any
malfunction.
4
3
4
5
6
2
1
7
Fig. 1
Package content
1 Gear lever knob with retention ring (1x)
2 Data cable (1x)
3 Reference box with power supply lines (1x)
4 Hexagon socket wrench (1x )
5 Grub screws – long and short (2x, one each)
6 Cable terminal clamps (2x)
7 Cable ties (1x)
5
Gear lever knob installation
Connect the plus line from the ignition and
ground line to the power supply lines of the
reference box (red to 12 Volt from the ignition,
black to ground). The included cable clamps can
be used here. Finding possible reference box
position. De-grease this surface for gluing on
the reference box (3) and clean it. Data cable
connection between the LCD gear lever knob and
reference box (3) (it is unimportant, which one of
the two sockets is used). Fasten data cable to the
gear lever with cable tie as strain relief!
1.2.2
Switch on ignition briefly to check display or
connections. Reprogrammed display shows a
rotating or running bar.
1.1.1
Disassembly of the original gear lever knob and
gear boot: Install LCD gear lever knob and gear
boot (the data cable at the gear lever knob must
not be damaged). The gear boot can be placed
between the gear lever knob and the retention
ring (to cover it) or below the retention ring.
For this, the retention ring can be pushed on in
two different directions (fig. 2 and 3) with radius
up or radius down.
1.2.1
Connection reference box (3):
The reference box should not be glued on before
programming of the colour.
Figure 2 Figure 3
6
Programming
the reference box once. Display now indicates a trans-
verse bar:
2.3.1
Fastening the reference box:
The box should be placed as horizontally as pos-
sible in the area of the switching lever. Labelling
points up. (Fig. 4)
2.3.2
Remove protective foil from the adhesive strips,
position reference box and press on firmly.
Verify that the gear lever is still set to idle. Now
acknowledge the box position by briefly pressing
the push-button.
(Programmes individual gear lever positions of
your car – for gear recognition and display)
2.1.1
The vehicle should be placed on a surface that
is as level as possible before programming.
Since the vehicle has to start in first gear after
programming (light acceleration), please ensure
now that there are no obstacles (20 metres
straight on are sufficient) and that traffic is not
impaired.
2.1.2
Start the engine – gear lever set to idle!
2.2.1
LCD Colour selection:
(Colour change by position change of the refe-
rence box). Keep the reference box button (3)
pressed for approx. 5 s until „C“ is displayed,
then let go of the button.
Tilt the reference box forwards and backwards
in your hand to start colour selection. The colour
changes in small nuances when the reference
box position is adjusted slightly. Briefly confirm
desired colour by pressing the push-button on
Figure 4
7
Once the display recognises acceleration, a
running bar is displayed:
After a few seconds, the number of the active
gear is displayed – here it is the number 1.
Your Indy-Cator gear display is now programmed
and ready for operation. Please switch off the
motor. (Programming remains saved with the
display/ ignition switched off). The gear boot
and any applicable covers in the car can now be
re-assembled.
2.3.3
Gear programming now starts. Starting in first
gear, the display now shows all gears in sequen-
ce as flashing figures.
2.3.4
Display:
1 > please switch to first gear
2 > please switch to second gear
3 > please switch to third gear
4 > please switch to fourth gear
5 > please switch to fifth gear
(if the vehicle only has 4 gears – ignore
display and leave it in 4th gear)
6 > please switch to sixth gear (if the vehicle
does not have any 6th gear – ignore
display and leave it in 5th (or 4th) gear
r > please switch to reverse gear
(if there is no gear-change, the display
change may take approx. 30 s).
1 > please switch back to first gear
A > Now accelerate the vehicle in first gear
(start driving as normal).
8
If re-programming is required, press the button of the reference box until „C“ is displayed and start
again as described on page 6. If the previously selected colour is to be retained, please confirm it
with the button without moving the reference box again.
Display only shows running ring
Troubleshooting
Gears not programmed
Gears are not recognised – displayed incorrectly
Changing LCD display brightness
Gear lever loose?
Reference casing loose?
Re-programme gears
Too many display instruments
connected to one reference box
Vehicle battery voltage too low
Programme gears
Inhaltsverzeichnis
Andere GASLOCK Messgerät Handbücher
