GCC Technologies RX II Series Bedienungsanleitung

V.24 2020 May

RX II Series

User Manual

http://www.GCCworld.com

V.24 2020 May

NOTICE

GCC reserves the right to modify the information contained in this user

manual at any time without prior notice; un-authorized modification, copying

distribution or display is prohibited. All comments, queries or

suggestions concerning this manual please consult with your local dealer.

RXIISeriesUserManual

Important Information

ImportantInformation

Thank you for purchasing the GCC RX II Series Cutting Plotter.

Before you use the cutting plotter, please make sure that you have read the

safety precautions and instructions below.

Caution

!SAFETYPRECAUTIONS!

ØFor safety concern, please always hold the cutter firmly from the bottom while moving

it. Do not move the cutter by clasping the depression area on both sides.

ØDo not shake or drop the blade holder, a blade tip can fly out.

ØDuring an operation, do not touch any of the moving parts of this machine (such as the

carriage). Also be careful to make sure that clothing and hair do not get caught.

ØAlways connect the power cable to a grounded outlet.

ØAlways use the accessory power cable which is provided. Do not wire the power cable

so that it becomes bent or caught between objects.

ØDo not connect the power cable to branching outlet to which other machines are also

connected, or use an extension cable. There is danger of overheating and of

mis-operation of the machine.

ØKeep the tools away from children where they can reach.

ØAlways put the pinch rollers within the white marks.

O (Correct) X (Incorrect)

RXIISeriesUserManual

Important Information

Warning

Never press the top release grip and pull the bottom release grip at the same time as

the pictures shown below:

O (CORRECT) ╳(INCORRECT)

Press down

DISABLE

ENABLE

Pullupbottomtoreleasegrip

Note:

In case the grips clipped

together due to your

wrong operation, please

use a pair of tweezers to

pull out the stop bar

when pressing down the

top release grip. Keep

the stop bar outside then

release the grips as the

right figure.

RX II Series User Manual

Table of Contents

Important Information

General Information

1.1 Introduction 1-1

1.2 Package Items 1-1

1.3 Product Features 1-2

1.4 Appearance of RX II series

1.4.1 The Front View 1-3

1.4.2 The Back View 1-4

1.4.3 The Whole View 1-5

1.4.4 The Left-hand Side 1-6

1.4.5 The Right-hand Side 1-6

1.4.6 The Pinch Roller 1-7

Installation

2.1 Precaution 2-1

2.2 Stand & Flexible Media Support System 2-2

2.3 USB Cable Tie and Saddle 2-8

2.4 Desktop Flexible Media Support System 2-10

2.5 Instruction of Damper Roller 2-12

2.6 Blade Installation 2-13

2.7 Automatic Blade Length Detection 2-17

2.8 Cable Connections 2-19

2.8.1 USB Interface 2-19

2.8.1.1 Connecting your GCC cutter 2-19

2.8.1.2 Installing the driver 2-20

2.8.1.3 Driver Un-installation 2-23

2.8.2 RS-232 Interface 2-26

2.8.3 Ethernet Connection 2-26

2.8.4 Data Transmitting 2-31

2.8.5 Printer Sever Shared Setting 2-31

2.9 Software Installation 2-34

2.9.1 GreatCut Installation 2-34

2.9.2 Sure Cuts A Lot Installation 2-39

2.9.2.1 Auto Installation 2-39

2.9.2.2 Manually Activate Software 2-43

2.9.2.3 Re-install Sure Cuts ALot Software 2-45

2.10 Auto Cut-off system Installation 2-46

The Control Panel

3.1 The LCD Panel 3-1

3.2 Menu in On-line Mode 3-3

3.3 Menu in Off-line Mode 3-4

3.4 Menu Items 3-6

Operation

4.1 Media Loading

4.1.1 Loading the Sheet Media 4-1

4.1.2 Loading the Roll Media 4-3

RX II Series User Manual

Table of Contents

4.2 Tracking Performance 4-6

4.3 Cutting Force and Offset Adjustment 4-7

4.4 How to Cut 3mm Letter 4-8

4.5 How to Make A Long Plot 4-8

4.6 When Completing the Cutting Job 4-9

4.7 RX II series Print Driver setting

4.7.1 RX II series Print Driver setting > Option Page 4-10

4.7.2 RX II series Print Driver setting > Pen Page 4-13

4.7.3 RX II series Print Driver setting > Paper Page 4-17

4.8 Reference Parameter Setting for Different Materials 4-18

utomatic

Aligning System

5.1 Introduction 5-1

5.2 AAS Contour Cutting System 5-2

5.2.1 Notice for Registration Marks 5-2

5.2.2 AAS II on RX II series 5-3

5.2.3 Automatic Distinction of the Plot Direction 5-5

5.3 Printer Test 5-6

5.4 Registration Mark Offset Range

5.5 Contour Cutting 5-8

5-8

5.6 Tips for AAS 5-10

. Maintenance

6.1 Cleaning the cutting Plotter 6-1

6.2 Cleaning the Grid Drum 6-2

6.3 Cleaning the Pinch Rollers 6-2

. Trouble Shooting

7.1 Non-Operational Problems 7-1

7.2 Operational Problems 7-2

7.3 Communication Problems 7-3

7.4 Software Problems 7-4

7.5 Cutting Quality Problem 7-5

7.6 USB Connection Problems 7-6

Appendix

A-1 RX II Series Specification A-1

A-2 Blade Specification A-2

A-3 CorelDRAW Output Instruction A-3

A-4 CorelDRAW Plug-In Instruction A-4

A-5 llustrator Plug-In Instruction A-5

A-6 GreatCut Plug-In Instruction A-6

A-7 SignPal 12 Instruction A-7

A-8 Sure Cuts A Lot A-8

RX II Series User Manual

General Information 1-1

Chapter 1 General Information

1.1 Introduction

RX II series cutting plotters have been designed to produce computer-generated images or

perform contour cutting on sheets or rolls of vinyl media.

This manual covers the following models of RX II series cutting plotters:

‧RX II-61 for media width: 50mm (1.97”) ~ 810mm (31.88”)

‧RX II-101S for media width: 50mm (1.97”) ~ 1326mm (52.2”)

‧RX II-132S for media width: 50mm (1.97”) ~ 1635mm (64.37”)

‧RX II-183S for media width: 50mm (1.97”) ~ 2145mm (84.44”)

1.2 Package Items

The package of the RX II series contents the items listed below, please check carefully.

If you find any item missing, please consult your local dealer for further assistance.

1. Cutting Plotter 1

Stand Set ( for

101S/

/183S

nly

)

(Optional for

61)

l2 piece of T-shape stand

l1 piece of stand beam

l18 pieces of M6 screws

l1 piece of M5 L-shape hexagon screw driver

l1 piece of Installation Guide for Stand Set

RX II Series User Manual

General Information 1-2

3. Flexible Media Support System Package

Items 183S/132S/101S 61

1 set of Roll Media Flange (2 pieces) V V

1 set of Roll Holder (2 pieces) V V

1 set of Roll Holder Guide Bushes (4 pieces) V V

1 set of Roll Holder Support (2 pieces) V V

1 piece of M6 L-shape hexagon screw driver V V

1 piece of Installation Guide for Roll Holder V

1 piece of M5 L-shape hexagon screw driver V

1 set of Desktop Support Brackets (2 pieces) V

4 pieces of Plastic Foot V

4 pieces of M4 screws V

12 pieces of M6 screws V

1 piece of M4 L-shape hexagon screw driver V

Accessor

ies

l1 piece of User’s Compact Disk

l1 piece of AC power Cord

l1 piece of data cable (USB cable: 3m)

l1 piece of Ethernet cable

l1 set of Blade Holder Assembly (Installed in tool carriage of the

cutting

plotter)

l1 piece of Blade (Installed in Blade Holder)

l1 piece of Safe Blade

l1 piece of Cutting Pad for Vinyl cutting

l1 piece of Tweezers

l1 piece of Promise Card

1.3 Product Features

The following are the main features of the RX II series cutting plotters:

‧Triple port (USB, serial and Ethernet port) connectivity

‧Up to 600-gram cutting force

‧Up to 1530 mm per second (60 ips) cutting speed (at 45° direction)

‧Can work with up to 0.8mm (0.03in) thick material

‧Guaranty 10-meter tracking

‧User friendly and multi-language control panel

‧Enhanced Automatic-Aligning System (AAS II) for automatic contour cutting

‧Ingenious media basket (optional item)

RX II Series User Manual

General Information 1-3

1.4 Appearance of RX II Series

1.4.1 The Front View (Figure 1-1)

Control panel –consists of 14

control keys and 1 LED and 1 LCM

showing messages and menus.

Cutting Pad –provides the

protection of blade when the blade is

cutting.

Tool Carriage –performs the

cutting with the installed blade

and pen with AAS module.

Alignment Rulers –

media can be aligned

with the clear guide line

marks.

Grid Drums – move

the media back and

forth during operation.

Slicer Groove –

slice off the extra

media easily along

this groove.

Platen –provides the

surface for holding and

supporting media while

performing cutting.

Figure 1-1

RX II Series User Manual

General Information 1-4

1.4.2 The Back View (Figure 1-2)

Pinch Rollers –

hold the media during

cutting.

Lever –

raises or lowers the

pinch rollers.

Figure 1-2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GCC Technologies Plotter Handbücher

GCC Technologies

GCC Technologies EXPERT 24 Bedienungsanleitung

GCC Technologies

GCC Technologies J5 Series Bedienungsanleitung

GCC Technologies

GCC Technologies P3-60 Bedienungsanleitung

GCC Technologies

GCC Technologies Jaguar IV Series Bedienungsanleitung

GCC Technologies

GCC Technologies EXPERT 24 LX Bedienungsanleitung

GCC Technologies

GCC Technologies Jaguar II Series Bedienungsanleitung

GCC Technologies

GCC Technologies AR-24 Bedienungsanleitung

GCC Technologies

GCC Technologies Jaguar IV Series Bedienungsanleitung

GCC Technologies

GCC Technologies BENGAL Bedienungsanleitung

GCC Technologies

GCC Technologies puma iii series Bedienungsanleitung

GCC Technologies

GCC Technologies EP-60 Bedienungsanleitung

GCC Technologies

GCC Technologies Jaguar V Series Bedienungsanleitung

GCC Technologies

GCC Technologies EXPERT 24 LX Bedienungsanleitung

GCC Technologies

GCC Technologies Expert 52 Bedienungsanleitung

GCC Technologies

GCC Technologies Puma Series Betriebsanleitung

Beliebte Plotter Handbücher anderer Marken

MUTOH

MUTOH Kona 760 Bedienungsanleitung

HP 7475a Bedienungsanleitung

Vulcan-Hart

Vulcan-Hart FC-500VC Bedienungsanleitung

Roland

Roland TrueVIS VG-640 Betriebsanleitung

Furuno

Furuno RP-180 Bedienungsanleitung

Roland

Roland VersaCamm SP-540V Bedienungsanleitung

MIMAKI

MIMAKI CF2 Series Bedienungsanleitung

Ioline

Ioline Summit Bedienungsanleitung

Summa

Summa S CLASS Bedienungsanleitung

Gerber Technology

Gerber Technology GERBERplotter MP Series Bedienungsanleitung

Furuno

Furuno RP-17 Bedienungsanleitung

HP 7470A Bedienungsanleitung

SII

SII LP-1010 Bedienungsanleitung

Great Computer

Great Computer JII-61 Bedienungsanleitung

Roland

Roland VersaUv LEF - 12i Bedienungsanleitung

Lectra

Lectra Alys 120 Bedienungsanleitung

MUTOH

MUTOH Ultima SC-850D Bedienungsanleitung

Skycut

Skycut D Series Bedienungsanleitung