GCC Technologies Elite 12/1200N Bedienungsanleitung

Elite12 SERIES INSTALLATION GUIDE

FEDERAL COMMUNICATIONS COMMISSION

WARNING: This equipment was tested and found to comply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency ener-

gy and, if not installed and used in accordance with the instructions in this manual, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference will not occur in a particu-

lar installation. For more information about radio frequency interference, refer to the section of this manual on

Radio and TV interference.

CANADIAN REGULATIONS

This equipment is a Class B digital apparatus that complies with the Radio Interference Regulations, CRC c.

1374.

IMPORTANT: Changes or modifications to this product not authorized by GCC Technologies Inc. could void

the FCC Certification and negate your authority to operate the product. This product was tested for FCC Com-

pliance under conditions that included the use of shielded cables and connectors between system compo-

nents. It is important that you use shielded cables and connectors to reduce the possibility of causing interfer-

ence to radios, television sets, and other electronic devices. You can obtain the proper shielded cables from

GCC Technologies or from an Authorized GCC Technologies dealer.

CLASS 1 LASER PRODUCT

LASER SAFETY: This printer is certified as a Class 1 laser product under the U.S. Department of Health and

Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and

Safety Act of 1968. This means that the printer does not emit hazardous radiation. Since radiation emitted

inside the printer is completely confined within protective housings and external covers, the laser beam can-

not escape from the machine during any phase of user operation. The Center for Devices and Radiological

Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August

1, 1976. These regulations apply to laser products marketed in the United States. The label on the printer indi-

cates compliance with the CDRH regulations and must be attached to the laser products marketed in the United

States.

Caution - Use of controls, adjustments, or performance of procedures other than

those specified in this manual may result in hazardous radiation exposure.

EPA ENERGY STAR COMPUTERS AWARD

The Elite 12 Series printer is designed to conserve electricity.

With its power-saving design, the Elite 12 Series qualifies for the

U.S. Environmental Protection Energy Star Computers Award.

CREDITS

The Elite 12 Series Installation Guide was written by David Field, Laurie Freitas, Wendi LeBlanc,

and Tom Linzey. It was edited by Donna Atwood, Kevin Curran, Lee Doron, Laurie Freitas, Wendi

LeBlanc, Tom Linzey, and David Nicholson. Illustrations by Bill Krech and Kathy Shackelford,

Cover design and layout by Adam DeFanti.

Fonts used in this documentation are from the Bitstream 45 collection that ships with the Elite 12 Series printer.

Installation Guide printed in USA. Part number 030.16463 Rev A.

INTRODUCTION

Congratulations on your purchase of a GCC Technologies Elite 12 Series laser printer. You now

have a high-quality, versatile solution to all of your printing needs. The purpose of this guide

is to show you how to set up your printer and install the software on the computer(s) that will

be using it.

CONFIGURATIONS

This printer is available in five configurations, as described below:

Elite 12/600 USB

Elite 12/600 N

Elite 12/600

Elite 1212

ECHNOLOGIES

A 600 dpi laser printer with both USB and

Parallel ports.

A networkable 600 dpi laser printer with USB,

Parallel and Ethernet ports.

A 600 dpi networkable laser printer with LocalTalk,

Parallel and Ethernet ports.

A high-resolution, networkable 1200 dpi laser printer

with LocalTalk, Parallel and Ethernet ports.

ECHNOLOGIES

Elite 12/1200 N

A high-resolution, networkable 1200 dpi laser printer

with USB, Parallel and Ethernet ports.

ECHNOLOGIES

WHERE TO LOOK FOR MORE INFORMATION

Several references are available for use with this printer. For additional copies of this guide,

contact GCC direct at 1.800.422.7777 (North America only, outside of North America refer

to the back cover) or contact your GCC authorized dealer. Additional information is available

at www.thevirtualprinterstore.com/support

INSTALLATION CHECKLIST

For proper installation please complete each section in order:

STEP 1CHECK PACKAGE CONTENTS

STEP 2PREPARE PRINTER LOCATION

STEP 3LOCATE PRINTER PARTS

STEP 4REMOVE INTERNAL PACKAGING

STEP 5INSTALL TONER CARTRIDGE

STEP 6LOAD TRAY

STEP 7ATTACH THE POWERCORD

STEP 8CONNECT THE PRINTER CABLES

STEP 9INSTALL PRINTING SOFTWARE

STEP 10 VERIFY PRINTER SETUP

STEP 1. CHECK PACKAGE CONTENTS

AC power cordToner cartridgeUniversal paper trayElite 12 printer

ECHNOLOGIES

Elite

™

12ppm

Configuration Page

Printer Information

Interfaces

Paper Handling

Language: English

AppleTalkName: Model

Page Count: 20

RAM Installed: 8MB

Hard disk: No disk

OS Version: 2.3

PostScript Level 2 Version:2.3

ROM Version:2.3

H/W Version:1.0

AccuGray: Enabled

Print Darkness: Normal

Default Source: Upper Tray

Default Size: Letter

Jam Recovery: Disabled

Paper Reserve: Enabled

Manual Feed Timeoutt: 5 Minutes

8-pin Serial: LocalTalk

RS422 Serial (Inactive)

Baude Rate: 9600

Data Bits: 8

Stop Bits: 1

Parity: None

Flow Control: Xon/Xoff

RS232 Serial (Active)

Baude Rate: 9600

Data Bits: 8

Stop Bits: 1

Parity: None

Flow Control: Xon/Xoff

Parallel Port (Active)

PS/PCLSensing: PostScript Only

Port Emulation

Parallel Port: Auto Switch

RS232 Port: Auto Switch

RS422 Port: Auto Switch

LocalTalkPort: PostScript Only

PostScript

Default Resolution: 800

Job Cancel: Enabled

Start Page: Disabled

WaitTimeout: 300 Seconds

PCLResolution: 600

Copies: 1

Font Source: Internal

Font Number: 1

Pitch: 10.0

Point Size: 12.0

Orientation: Portrait

Page Length: 60

Symbol Set: Roman-8

WaitTimeout: 120 Seconds

Line Wrap: Disabled

Line Termination: Normal

Emulations

Configuration page Installation guide Elite 12 Series CD-ROM USB cable*

NOTE

* The Elite 12/600 USB ships with a USB cable. A printer cable is not included with

any other 12 series model. For information on ordering cables contact GCC at

1.800.422.7777 (North America only. Outside of North America refer to the back cover)

or www.thevirtualprinterstore.com

STEP 2. PREPARE PRINTER LOCATION

Minimum recommended clearances.

Place the printer on a flat level surface in a well-ventilated area away from direct sunlight or

areas where the air temperature and humidity can vary widely. Do not obstruct the fan vent

on the right side of the printer.

16.6 inches (422mm)

minimum overhead

clearance.

7.1 inches

(180mm)

1 inch

(25mm)

12.2 inches

(310mm)

10.6 inches

(270mm)

STEP 3. LOCATE PRINTER PARTS

ECHNOLOGIES

Top output tray

Cover release

Multi-purpose tray

Paper tray

Control panel

Connectivity ports

Rear output

Power switch

Power outlet

FRONT VIEW

REAR VIEW

A: Serial/LocalTalk

B: HD30* (for font hard drive)

C: Parallel

D: Ethernet (10 BaseT [top], 10 Base2* [bottom])

*1212 model only

Parallel

Ethernet

HD 30

Serial/

LocalTalk

USB

PARALLEL

ELITE 12/600 USB

ELITE 12/600, ELITE 1212

A: USB

B: Parallel

A: USB

B: Parallel

C: Ethernet 10 BaseT

USB

PARALLEL

10-BASE-T

ELITE 12/600 N, ELITE 12/1200 N

CONNECTIVITY PORTS

With the printer’s

all ports active feature, all

the interfaces are

simultaneously active,

which means you can

connect more than one

interface at a time. You

don’t have to select a port;

this feature works

automatically.

STEP 4. REMOVE INTERNAL PACKAGING

GCC

TECHNOLOGIES

Elite

12/600U

GCC

ECHNOLOGIES

GCC

ECHNOLOGIES

1. Remove the tape from the printer’s top cover.

NOTE

Save all packaging material, you may need to repack the printer at a later date.

2. Press the release button on the top right of

the printer.

3. Lift open the printer cover.

4. Remove the plastic foam block.

Andere Handbücher für Elite 12/1200N

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GCC Technologies Drucker Handbücher

GCC Technologies

GCC Technologies JV-240UV Bedienungsanleitung

GCC Technologies

GCC Technologies Elite XL-1208 Montage- und Wartungsanleitung

GCC Technologies

GCC Technologies 16 Bedienungsanleitung

GCC Technologies

GCC Technologies Elite XL Bedienungsanleitung

GCC Technologies

GCC Technologies Elite Color 16 series Firmware-Update

GCC Technologies

GCC Technologies Elite Color 16DN Firmware-Update

GCC Technologies

GCC Technologies X500III Bedienungsanleitung

GCC Technologies

GCC Technologies LaserPro X500 III-80Y Bedienungsanleitung

GCC Technologies

GCC Technologies puma iii series Bedienungsanleitung

GCC Technologies

GCC Technologies 21 Series Bedienungsanleitung

GCC Technologies

GCC Technologies Elite Color 16 series Firmware-Update

GCC Technologies

GCC Technologies Elite 21DN+ Bedienungsanleitung

GCC Technologies

GCC Technologies JF-2418UV Bedienungsanleitung

GCC Technologies

GCC Technologies Elite XL-1208 Handbuch

GCC Technologies

GCC Technologies Elite XL-20/1200 Montage- und Wartungsanleitung

GCC Technologies

GCC Technologies RX Series Bedienungsanleitung

GCC Technologies

GCC Technologies Elite Color 16 series Firmware-Update

GCC Technologies

GCC Technologies T500 Bedienungsanleitung

GCC Technologies

GCC Technologies Elite XL-20/1200 Montageanleitung

GCC Technologies

GCC Technologies Elite 12 Series Kurzanleitung

GCC Technologies

GCC Technologies Elite XL-1208S Handbuch

GCC Technologies

GCC Technologies LaserPro C180II Bedienungsanleitung

GCC Technologies

GCC Technologies JF-240UV Bedienungsanleitung

GCC Technologies

GCC Technologies Jaguar IV Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung