GE 25007 Bedienungsanleitung

cbl

aux

fav pip input

aspect swap

liveactive

backlight

b-ray

dvd aux2

amp sat

456

123

vod

dvr/list back

page

B C

setup

shift

menu guide exit

Universal Remote

Instruction Manual

Control Remoto Universal

Manual de Instrucciones

25007

7252

Congratulations on your purchase of the GE Universal

Remote. This remote is capable of operating

thousands of audio/video devices including TVs, DVD

players, cable, satellite reveivers and more!

IMPORTANT: SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

Introduction..................................................................................... 2

Setup .................................................................................................. 3

Button Functions .......................................................................... 4

Programming Your Remote..................................................... 6

Direct Code Entry................................................................... 6

Auto Code Search ................................................................. 8

Using Your Remote ................................................................... 11

Controlling Combo Devices............................................11

Using SHIFT............................................................................11

Master Volume Feature...........................................................12

Reset to Factory Settings........................................................13

Troubleshooting..........................................................................14

Warranty ........................................................................................15

FCC Statement.............................................................................16

Table of Contents

Scan to view

remote setup video

Mira a ver el video de

instalación remota

http://www.jascoproducts.com/remote

Your universal remote requires two (2) AAA batteries

(not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, pull down on

the textured surface and slide battery cover

downward to remove.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AAA batteries. Be sure to use

fresh batteries.

3. Position battery cover slightly below opening and

push upward to lock into place.

NOTE: If your remote stops operating properly,

replace the batteries with new ones. The remote will

retain the codes you have programmed for up to 10

minutes after the batteries are removed.

Battery Precautions

• Donotmixoldandnewbatteries.

• Donotmixalkaline,standard(carbon-zinc),or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Alwaysremoveold,weakorworn-outbatteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote. If

buttons are pressed without batteries in the remote,

all codes will be lost.

Setup

cbl

aux

fav pip input

aspect swap

liveactive

backlight

b-ray

menu guide exit

dvd aux2

amp sat

456

123

vod

dvrlist back

page

B C

setup

shift

Button Functions

DOT ( ) Used to select

digital channels, e.g., 2.3.

VOLUME UP/DOWN

Changes the volume level

of the product, normally

the TV.

MUTE ( )Turns off the

TV sound while the

picture remains.

FAVORITE Used to

store 10 of your

favorite channels for

quick access.

RECORD, PLAY, STOP,

REW (rewind), FF (fast

forward), PAUSE

TV, CBL, B-RAY, AUX, (AMP,

SAT, DVD, AUX2 in SHIFT

mode)

Selects device to control.

UP, DOWN,

LEFT & RIGHT

Navigation buttons.

ABCD (yellow, blue,

red and green) Allows

access to additional

features for DVRs, cable

box, satellite, Blu-ray™,

etc... (additional features

vary by device type

and brand, see device

owner's manual for

information).

GUIDE Displays satellite or

cable on-screen program

guide.

MENU Displays the

Menu on the TV.

cbl

aux

fav pip input

aspect swap

liveactive

backlight

b-ray

menu guide exit

dvd aux2

amp sat

456

123

vod

dvrlist back

page

B C

setup

shift

OK Selects menu items

for the device you are

controlling.

Button Functions, cont.

NUMBERS Enter

numbers for direct

channel selection.

Some devices require

ENTER to be pressed

after channel selection.

POWER Turns devices On or Off and

functions as red indicator light

CHANNEL UP/DOWN

Changes the channels.

INPUT Selects the video

inputs from available

viewing sources.

INFO (i) Displays

on-screen channel

information, etc.

EXIT Exits

On-Screen Menus.

LAST ( ) Returns to

the previously selected

channel, or DVD

repeat toggle.

SETUP Used to setup the

remote, and for code

search function.

SHIFT Press and release

to access buttons

labeled in blue print

(AMP, SAT, DVD, AUX2,

VOD, DVR/LIST, ASPECT,

SWAP, PAGE, ACTIVE,

LIVE, BACKLIGHT).

Programming Your Remote

Your GE universal remote control is designed to

control multiple audio/video devices such as a TV,

DVD, DVR, satellite, cable and audio device using

only one remote. To use this remote, you will need to

program it to control the devices of your choice. There

are two ways to program the remote - direct code

entry or auto code search.

Direct Code Entry (Recommended)

1. Locate the Remote Code List provided.

Find the DEVICE CATEGORY you wish

to program (for example TV, CBL, DVR,

B-RAY, SAT, AMP, AUX 1, AUX 2) and

then ﬁnd the BRAND of that device.

Circle all the codes under that brand.

Example: For a GE TV, locate the TV

code section then circle all of the GE

TV codes.

2. Manually turn on the device you wish

to control.

3. Press and hold the SETUP button

until the red indicator light stays on

(approximately 2 seconds) and then

release the SETUP button.

4. Press and release the device button

on the remote (TV, CBL, B-RAY, SAT,

AUX) or SHIFT button for secondary

functions (AMP, SAT, DVD, AUX 2). See

"Using Shift for Menu and Navigation"

for additional information. The red

indicator will blink once and then

remain on.

5. Enter the ﬁrst 4-digit code previously

found in the code list using the

number buttons on the remote. If the

code entered is a valid code, the red

indicator light will turn off. If the code

entered is not a valid code, the red

indicator light will ﬂash and remain on

allowing you to re-enter the code.

setup

456

123

Programming Your Remote, cont.

Note: If no buttons are pressed for

35 seconds, the remote will exit the

SETUP mode and you will have to

start over.

6. Point the remote at the device. Press

the POWER button—if the device

turns off, no further programming is

required for that device. If the device

does not turn off, return to step 3 and

use the next code found in the code

list. Continue this process until a code

for your device is found.

7. Repeat this process for each device

(for example TV, CBL, DVR, B-RAY,

SAT, AMP, AUX 1, AUX 2) in your home

entertainment system you wish

to control.

Programming Notes

• Ifyourdevicedoesnotrespondtotheremoteafter

trying all codes listed or your brand is not listed in

the code list, use the Auto Code Search method to

program your remote.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Try other codes

from the code list for more functionality.

• WiththeDirectCodeEntrymethod,youcan

program any device button to control any device

in your home entertainment system.

For example, you can use the B-RAY or AUX device

button to control an audio receiver or a DVD, VCR,

satellite device, etc.

• Forcombinationdevices,youmayhavetoentera

code for each device. For example, for a DVD/VCR

device, you may have to enter a code for the DVD

under the DVD button and enter a code for the

VCR using a different device button on the remote.

• Writedownthecodefoundtooperateyourdevice

for future reference.

Programming Your Remote, cont.

Auto Code Search

The Auto Code Search searches automatically

through the codes stored in this remote. Read all the

following steps prior to starting the auto code search

as you will need to be prepared to lock-in the proper

code when found.

1. Manually turn on the device you wish

to control.

2. Press and hold the SETUP button

until the red indicator light stays on

(approximately 2 seconds) and then

release the button.

3. Press and release the desired device

button on the remote (TV, CBL, DVR,

B-RAY, SAT, AMP, AUX 1, AUX 2) the

type of device you wish to control. The

red indicator will blink once and then

remain on.

4. Point the remote at the device and

press and release the POWER button

(for TV) or PLAY button (for DVD, VCR,

etc.) to start the search. The red

indicator will ﬂash (approximately every

2 seconds) as the remote searches.

Note: The remote must be pointed

at the device for the duration of this

search.

5. Place your ﬁnger on the #1 button so

you are prepared to lock-in the code.

6. When the device shuts off or begins

playing, press the #1 button to lock-in

the code. The red indicator light will

turn off. Note: You have approximately

two seconds after the device shuts off or

begins playing to lock-in the code.

7. Point the remote at the device and

check to see if the remote operates the

device as desired. If it does, no further

programming is required for that

device. If it does not, return to step 2

and start the auto code search again.

setup

Programming Your Remote, cont.

8. Repeat this process for each device (for example

TV, B-RAY, SAT, AUX) in your home entertainment

system you wish to control.

Programming Notes

• Thisprocessmaytakeseveralminutesasthe

remote contains many codes.

• WhenusingtheAutoCodeSearchprogramming

method, the device button corresponding to

the type of device you want to control must be

selected (for example, the TV device button must

be selected in step 3 if you want to control a TV,

the DVD device button for a DVD player, etc.)

• TheSETUP button can be used during the search

process to reverse the direction of the search of

the remote codes. For example, if you miss the

code for your device and the remote is continuing

to search (as indicated by the blinking red light),

press the SETUP button and the code search will

reverse direction and return to the code.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Continue the

auto code search as directed above until the best

code is found.

Programming Your Remote, cont.

Favorite Function

Allows user to program up to 10 of their favorite

channels for quick access.

Setup Favorite Function

1. Press and release the device button (tv,

cbl, dvr, etc). The indicator light will blink

once. Special Note: User must select

the device type that controls the

channels; for example if a user has a

Cable Box for controlling channels, then

this device button must be selected to

properly change the channels on the

cable box.

2. Press and hold the SETUP button for 2

seconds or until the red indicator light

turns on, then release the SETUP button.

3. Press and release the FAV button. The

red indicator will blink once and

remain on.

4. Press and release the numerical button

(0 – 9) that you will use for storing your

favorite channel. The red indicator will

blink once and remain on.

5. Enter the channel number you wish to

program, for example channel 4, 21,

4-1, 52-2.

6. Press and release the FAV button, the red

indicator will turn off. Your favorite

channel is now saved.

Using Favorite Function

• Press and release the FAV button. The red

indicator light will turn on. Press and release the

programmed button (0-9) The red indicator will

blink twice and the remote will send the code for

your pre-programmed channel.

setup

fav

456

123

456

123

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung