GE 41567 Bedienungsanleitung
Universal Remote
Instruction Manual
Control Remoto Universal
Manual de Instrucciones
41567
1/18 v1
7252
2
Scan this to view
a helpful remote
setup video
http://www.byjasco.com/remote
Congratulations on your purchase of this GE-branded
Universal Remote Control. This remote is capable of
operating thousands of audio/video devices including
TVs, Blu-ray™/DVD players, streaming media players,
sound bars, cable receivers and more!
Introduction..................................................................................... 2
Setup .................................................................................................. 3
Button Functions .......................................................................... 4
Programming Your Remote..................................................... 6
Direct Code Entry................................................................... 6
Auto Code Search ................................................................. 7
Controlling Combo Devices.............................................. 9
Using Your Remote.............................................................10
Master Volume Feature....................................................10
Code Identification.....................................................................11
Reset to Factory Settings.................................................11
Troubleshooting..........................................................................12
Warranty ........................................................................................13
FCC Statement.............................................................................14
Table of Contents
SAVE THIS MANUAL AND CODE LIST
FOR FUTURE REFERENCE
3
Your universal remote requires two (2) AA batteries
(not included). Alkaline batteries are recommended.
Battery Installation
1. On the back of the remote, pull down on
the textured surface and slide battery cover
downward to remove.
2. Match the (+) and (-) marks on the batteries to the
(+) and (-) marks inside the battery compartment,
then insert two (2) AA batteries. Be sure to use
fresh batteries.
3. Position battery cover slightly below opening and
push upward to lock into place.
NOTE: If your remote stops operating properly, replace
the batteries with new ones.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Always remove old, weak or worn-out batteries
promptly and recycle or dispose of them in
accordance with local and national regulations.
Battery Saver
Your remote automatically turns off if the buttons are
depressed more than 8 seconds. This will save your
batteries should your remote get stuck in a place
where the buttons remain depressed (e.g., between
the sofa cushions).
Code Saver
You have up to 10 minutes to change the batteries
in your remote without losing the codes you have
programmed.
Setup
4
Button Functions
3
2
1
456
9
8
7
0enter
input
dvd
strm
aud
sat
cbl
b-ray
setup
ch
ok
0l
v
tv
app
menu
ABC
D
aux
3
1
4
17
18
15
12
6
14
11
9
13
16
3
10
8
5
20
19
21
7
2
5
Button Functions
1. Power - Turns devices ON/OFF
2. Input - Selects video inputs
3. TV, strm, dvd, aud, b-ray, cbl, sat, aux, - Selects
the device to control
4. Up/Down/Left/Right - menu navigation
5. Ok - Selects menu items for the controlled device
6. Mute - Mutes sound
7. Previous Channel - Returns to the previously
selected channel
8. Setup - Used to program the remote
9. Streaming App Hotkey - Access top apps like
Netflix®, Amazon® Prime, Hulu® and more
10. Info - Displays on-screen show/content
information
11. Home/Guide - Easily access features on today’s
streaming devices, or Guide on cable/satellite
receivers
12. Exit - Exit on-screen menus
13. Channel Up/Down
14. Menu - Displays the on-screen menu
15. Volume Up/Down
16. DVD/Blu-ray™ open/close - open/close a player,
or List features on cable/satellite receivers
17. Record, play, stop, rewind, fast forward, pause
18. ABCD - Access additional features for DVRs, cable
and satellite receivers
19. Numbers - Enter numbers for direct channel
selection
20. Dot (•) - Used to select digital channels, e.g., 4.1
21. Enter key - (Some devices require enter to be
pressed after channel selection)
6
Programming Your Remote
Your remote is designed to control multiple audio/video
devices. To use, you will need to program the remote for
your devices. There are two different methods you can
use to program the remote, Direct Code Entry or Auto
Code Search.
• The Direct Code Entry method is the recommended
method as it is the simplest and quickest method in
most cases.
• The Auto Code Search method searches through all
the codes in the remote to find a code for
your device.
Note: This remote comes preprogrammed for Roku®boxes and
Samsung TVs. Press TV for Samsung TVs and strm for Roku boxes.
Direct Code Entry (Recommended)
1. Locate the Code List included with
your remote. Find the section for the
type of device you wish to control,
(for example TV, dvd, strm, aux, b-ray,
cbl, sat, amp). Locate the brand of your
device and circle all the remote codes
for the brand.
2. Press and hold down the SETUP button
on the remote until the red light on the
remote control turns on. Release the
SETUP button. The red light will
remain on.
Note: The red light will either be a small light at the
top of the remote or the power ON/OFF button.
3. Press and release the device button on
the remote for the type of device you
wish to control, (for example tv, dvd,
strm, aux, b-ray, cbl, sat, amp). The red
light will blink once and remain on.
Note: Any of the device buttons on the remote can
be programmed to control any of your devices. For
example, you can use the CBL device button on
the remote to control a Satellite Receiver, Digital
Converter Box, Streaming Media Player or any
device category in the Code List.
4. Use the number buttons on the remote
to enter the first 4-digit remote code
you circled in the Code List in Step 1.
tv
setup
3
2
1
456
9
8
7
0
7
Programming Your Remote
The red light will turn off after entering
the fourth digit.
5. Point the remote at the device. Test
the buttons on the remote to see if the
device responds as you would expect. If
the buttons do not operate the device,
return to Step 2 above and use the next
code that you circled for that device.
6. Repeat Steps 1 – 5 for each device you wish to
control.
Programming Notes
• Some codes may operate only a few functions of your
device. There may be another code in the Code List
that controls more functions. Test other codes in the
Code List for more functionality.
• If you do not find a remote code that works your
device or there are no codes in the Code List for your
device, use the Auto Code Search method in the next
section to program your remote.
• For combination devices such as a TV/DVD combo
or TV/ VCR combo, you may have to enter a code for
each device. (See Controlling Combo Devices, pg. 9.)
• Write down the remote codes used to program the
remote for future reference.
Auto Code Search
The Auto Code Search is a process where you can
search through all the codes stored in the remote to find
a code for your device. It is recommended that you read
through all the steps below to familiarize yourself with
the Auto Code Search before starting the process.
1. Manually turn on the device you wish
to control.
Note: The Auto Code Search process cannot be
used for devices without power ON/OFF capability.
Use the Direct Code Entry method in these cases.
2. Press and hold down the SETUP button
on the remote until the red light on the
remote control turns on. Release the
SETUP button. The red light will remain on.
setup
8
Programming Your Remote
Note: The red light will either be a small light at the top
of the remote or the power ON/OFF button.
3. Press and release the device button on the
remote for the type of device you wish to
control, (for example tv, dvd, strm, aux,
b-ray, cbl, sat, amp). The red light will blink
once and remain on.
4. With the remote pointed at the device,
press and release the POWER button
on the remote. The remote will send 10
different codes to the device. The red light
will blink once for each code and remain on
after sending the 10 codes.
Did the device turn off?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the next
10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the device,
press and release the VOL + button. The
remote will re-send the first code of the 10
codes from Step 4. The red light will blink
once and remain on.
Did the device turn off?
• If YES, you have found a code for the
device. Press and release the same device
button you pressed in Step 3. This will
store the code in the remote. Go to Step 7.
• If NO, continue to press and release the
VOL + button until the device turns off to
test the other 9 codes from Step 4.
Be sure to wait approximately 3 seconds
after each VOL + button press to allow
the device time to respond to the code.
When the device turns off, you have
found a code for your device. Press and
release the same device button pressed
in Step 3. This will store the code in the
remote. Go to Step 7.
tv
0l
v
0l
v
9
Programming Your Remote
Notes:
• The VOL – button can be used to go backwards through
each batch of 10 codes.
• The red indicator light will flash 2 times after testing the first
or last code in each batch of 10.
7. Use the remote to turn the device back on.
Test the buttons on the remote to see if the
device responds as you would expect. If the
buttons do not operate the device, return to
Step 2 and repeat this process to search for a
better code to operate the device.
8. Repeat this process for each device you wish
to control.
Controlling Combo Devices
Some combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR,
etc.) will require you to set up two different device
buttons to control both parts of the combo device.
For example, if you have a TV/DVD combo, you may
need to set up one code under the tv button to
control the TV and a separate code under the dvd
button to control the DVD.
10
Master Volume Feature
The Master Volume Feature allows you to select a
single device that the volume buttons always control.
For example, the remote can be in TV mode while
the volume buttons control the volume on your audio
receiver or sound bar instead of your TV.
Enabling the Master Volume Feature
1. Press and hold down the SETUP button
on the remote until the red light on the
remote control turns on. Release the
SETUP button. The red light
will remain on.
2. Press and release the device button
(tv, aud, etc.) on the remote for the
device you wish to control the volume.
3. Press and release the MUTE button.
4. Press and release the VOL+ button.
The red light will blink twice and
turn off.
Disabling the Master Volume Feature
1. Press and hold down the SETUP button
on the remote until the red light on the
remote control turns on. Release the
SETUP button. The red light will
remain on.
2. Press and release the device button
(tv, aud, etc.) programmed to control
the Master Volume Feature.
3. Press and release the MUTE button.
4. Press and release the VOL - button.
The red light will blink twice and
turn off.
Using Your Remote
tv
0l
v
tv
0l
v
setup
setup
Inhaltsverzeichnis
Sprachen:
Andere GE Fernbedienung Handbücher
GE
GE RSP12 Bedienungsanleitung
GE
GE 45600 Bedienungsanleitung
GE
GE 24116 - 4 - Device Universal Remote Bedienungsanleitung
GE
GE Cync CWLRMDMBWM1 Bedienungsanleitung
GE
GE HC-TX20 Bedienungsanleitung
GE
GE HC-DRXRGB1 Bedienungsanleitung
GE
GE 24993 Bedienungsanleitung
GE
GE 94931 Bedienungsanleitung
GE
GE RM91902 Bedienungsanleitung
GE
GE UltraPro 44220 Bedienungsanleitung
GE
GE 25008 Bedienungsanleitung
GE
GE 25007 Bedienungsanleitung
GE
GE YR-HQ Bedienungsanleitung
GE
GE 37123 Bedienungsanleitung
GE
GE 94902 Bedienungsanleitung
GE
GE HC-TX10 Bedienungsanleitung
GE
GE 45601 Bedienungsanleitung
GE
GE 94948 Bedienungsanleitung
GE
GE 94906 Bedienungsanleitung
GE
GE 12726 Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
