GE 45413 Bedienungsanleitung

Personal Security

Glass

Vibration

Alarm

User Manual

Do not use in wet locations

Important Safeguards 4

Introduction 5

Installing Batteries 6

Low Battery Indicator 7

Installation 7-9

Operation 10

Sensitivity Selection 10

Care and Maintenance 11

Speciﬁcation 12

Warning 13-15

Table of Contents

Before connecting or operating the Glass Vibration Alarm, please read these instructions

carefully and save this manual for future reference.

This user manual explains in simple steps how to install, use and care for your new Personal

Security Glass Vibration Alarm.

If you have any questions or would like additional information please visit our web site

www.jascoproducts.com or contact our Technical Support Group at 1-800-654-8483,

option 4.

4

Important safeguards

Pre cautions

1. Do not attempt to disassemble the Glass Vibration Alarm, unless described in the user’s

manual. There are no user serviceable parts.

2. Handle with Care – Avoid striking or shaking. Improper use or storage could damage

the Glass Vibration Alarm. Modifying the device or its internal components can cause a

malfunction and void the Alarm’s warranty.

3. If you feel the Glass Vibration Alarm is not operating correctly or as described, please

contact Technical Support for assistance (1-800-654-8483), option 4.

5

Introduction

The Glass Vibration Alarm is designed to be mounted on glass where there is a potential

for tampering or breakage. The thin proﬁle makes it ideal for mounting between sliding

windows and glass doors. When mounted properly it will sound an alarm when glass

has been broken or there is excessive

vibration. The alarm has a printed

warning label visible from the outside. (HI/LOW)

High & Low

sensitivity section

Indicator Light

Alarm

Siren

Battery Test Button

Power ON/OFF

Battery

compartment

6

Installing Batteries

The alarm requires (4) LR44 or 357 button batteries (included).

Average battery life for typical usage is up to one year.

1. Make sure alarm ON/OFF switch is set to “OFF” position.

2. Remove the screw securing the battery compartment cover.

3. Slide cover off the battery compartment in direction of arrow.

4. Insert (4) LR44 button batteries noting polarity.

5. Replace battery compartment cover.

6. Secure the battery cover screw.

7

Low Battery Indicator

The alarm has a low battery indicator light. Push the ‘Battery Test’ button located

on the front of the unit. Batteries can be tested in either ON/OFF mode. If the red

light illuminates when the button is pressed, the batteries are good. If the light fails

to illuminate, replace all batteries.

Installation

Your GE Personal Security Glass Vibration Alarm is an octagon shaped alarm with

a visible warning sticker on opposite side (facing out). Before mounting to glass

ensure proper orientation so that warning sticker can be easily viewed.

8

1. Locate a position on the window or sliding glass door to be protected that allows

easy access to the alarm controls, and access to the battery door. Make sure

switch is in the OFF position, and the mounting surface is clean and dry. For best

results, clean the mounting surface with a mixture of 50% isopropyl alcohol and

50% water. Allow to dry.

2. Remove protective covering from the back side of the double-sided tape and lightly

position the alarm on the glass window or sliding glass door in a visible location.

3. Ensure that warning label can be easily viewed from outside and that you can easily

access all the controls and battery door. Once correct placement is established,

apply pressure to secure double-sided tape.

9

Your GE Personal Security Glass Vibration Alarm has a thin proﬁle and can be

placed between sliding windows and sliding glass doors. Note: There must be at

least a 3/8” gap between windows and doors to prevent damage to alarm.

Window and door preferred

mounting location

10

Operation

1. To arm the alarm, locate the ON/OFF switch on the side. Slide the switch to the

“ON” position. When in the “ON” position, if the protected window or door is struck

or hit, the alarm siren will sound continuously until disarmed.

2. To disarm the alarm, slide the switch to the OFF position.

Sensitivity Selection

The GE Glass Vibration Alarm has a selectable HI/LO sensitivity switch. Locate the

switch on the side and select the desired sensitivity setting. Select “LO” position for

windows or doors that may be exposed to vibration from strong winds.

Inhaltsverzeichnis

Andere GE Sicherheitssystem Handbücher

GE

GE TX-6310-01-1 b Bedienungsanleitung

GE

GE Concord express Bedienungsanleitung

GE

GE 4 Series Bedienungsanleitung

GE

GE Concord Bedienungsanleitung

GE

GE Choice-Alert 45136 Bedienungsanleitung

GE

GE Simon XTi Bedienungsanleitung

GE

GE AS272 Bedienungsanleitung

GE

GE VT71230-R3 Installationsanleitung

GE

GE SIMON XT Bedienungsanleitung

GE

GE NX-10 Benutzerhandbuch

GE

GE Concord 4 Bedienungsanleitung

GE

GE Concord 4 Bedienungsanleitung

GE

GE NX-10 Bedienungsanleitung

GE

GE ActiveKEY Bedienungsanleitung

GE

GE 60-806-95R-16Z - Security Concord Express System Control... Bedienungsanleitung

GE

GE Concord 4 Gebrauchsanweisung

GE

GE Deluxe 45117 Bedienungsanleitung

GE

GE SuperBus 2000 Bedienungsanleitung

GE

GE 45411 Bedienungsanleitung

GE

GE 60-362 Bedienungsanleitung

GE

GE AL-1291 Point ID Bedienungsanleitung

GE

GE Interlogix 60-875 Simon Bedienungsanleitung

GE

GE 45232 Bedienungsanleitung

GE

GE 56789 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung