GE 8RP Board Montageanleitung

1 of 6 P/N 460235001J • ISS 21MAR08

Security

8RP Board

Installation Sheet

Introduction

This installation sheet is designed to help experienced

technicians install the 8RP Board quickly. For more detailed

information, refer to the appropriate controller installation

manual.

The number of 8RP Boards supported by different host

software systems varies. Consult the manual that came

with your software for this information.

Features include:

• Each 8RP Board is limited to only one type of reader

technology: F/2F or supervised F/2F.

• External pull-up resistors are not required for the 8RP

Board.

• No door DI (alarm) or exit DI points are available on the

8RP Board. Use of supervised readers is recommended

since these points are available on the reader.

• If keypad readers are needed, use only GE supervised

F/2F keypad readers or Wiegand Interface Units (WIU-

2/WIU-4).

• Each reader, reader-based DI (input) point, and reader-

based exit DI on the 8RP Board is addressed differently

depending on the host system you are using.

• The 8RP Board provides one digital output (reader LED)

per reader port, 12 VDC, 100 mA maximum per output

point.

Verify contents

Caution: While the 8RP has been designed to resist

electrostatic damage (ESD), it can be damaged by such

discharges. Always observe proper ESD precautions when

handling and storing the 8RP.

Inspect the package and contents for visible damage. If any

components are damaged or missing, do not use the unit;

contact the supplier immediately. If you need to return the

unit, you must ship it in the original box.

The package should include the following contents:

• 8RP Reader Board

• 8RP Board Installation Sheet (this document)

• 1N4004A protection diodes

• MOV varistors

• 8-position, 45-degree connectors

Figure 1: 8RP Board layout

2 of 6 P/N 460235001J • ISS 21MAR08

Device addressing

Picture Perfect

Picture Perfect uses 2RP Board numbers to address

readers, DIs, and DOs on the 8RP Board. See Table 1 and

Table 2 for further information. Picture Perfect uses the

following addressing:

• Reader ports 1 and 2 are configured as board number

1, reader address 0 and 1

• Reader ports 3 and 4 are configured as board number

2, reader address 0 and 1

• Reader ports 5 and 6 are configured as board number

3, reader address 0 and 1

• Reader ports 7 and 8 are configured as board number

4, reader address 0 and 1

Table 1: 8RP device addressing - Picture Perfect Board 1

Board type: Board 1 [1}

Reader 1

and 2

Reader 3

and 4

Reader 5

and 6

Reader 7

and 8

Picture Perfect

board number

1 2 3 4

Readers 0 and 1 0 and 1 0 and 1 0 and 1

Door DIs 0 and 1 0 and 1 0 and 1 0 and 1

Exit DIs 8 and 9 8 and 9 8 and 9 8 and 9

Door DOs 0 and 1 0 and 1 0 and 1 0 and 1

[1] The first 8 readers out of 16. See Table 5 for board type settings.

Table 2: 8RP device addressing - Picture Perfect Board 2

Board type: Board 2 [1]

Reader 9

and 10

Reader 11

and 12

Reader 13

and 14

Reader 15

and 16

Picture Perfect

board number

5 6 7 8

Readers 0 and 1 0 and 1 0 and 1 0 and 1

Door DIs 0 and 1 0 and 1 0 and 1 0 and 1

Exit DIs 8 and 9 8 and 9 8 and 9 8 and 9

Door DOs 0 and 1 0 and 1 0 and 1 0 and 1

[1] The second 8 readers out of 16. See Table 5 for board type settings.

Facility Commander Wnx and Secure Perfect

The Facility Commander Wnx and Secure Perfect systems

create the device addresses shown in Table 3. (Table 3 is

included for your reference only.)

The device address is in the format mmmm-b-pp where

mmmm represents the controller number, b represents the

board number, and pp represents the point or device

number.

Table 3: 8RP device addressing - FCWnx and Secure Perfect

Standard/Board 1 Board 2

Readers/Door DO mmmm-1-01

through

mmmm-1-08

mmmm-2-01 through

mmmm-2-08

Door DIs mmmm-1-01

through

mmmm-1-08

mmmm-2-01 through

mmmm-2-08

Exit DIs mmmm-1-01

through

mmmm-1-08

mmmm-2-01 through

mmmm-2-08

Setting the DIP switches

Set the DIP switches as described in the tables below before installing and wiring the 8RP Board.

Table 4: DIP switch settings for reader technology and format

Reader technology and format SW 1-1 SW 1-2 SW 1-3 SW 1-4

Magstripe - GE supervised F/2F ON OFF ON OFF

Magstripe - F/2F ON ON ON OFF

P/N 460235001J • ISS 21MAR08 3 of 6

Table 5: 8RP Board address settings

SW 1- SW 2-

Board type 5 6 7 8 1 2 3 4 5 6 7 8

Board 1 [1] N/A N/A OFF ON ON OFF ON OFF ON OFF ON OFF

Board 2 [2] N/A N/A OFF ON ON ON OFF OFF OFF ON OFF ON

[1] The first 8 readers out of 16.

[2] The second 8 readers out of 16.

Wiring

It is recommended that 20 AWG shielded cable be used

for wiring reader DOs and DIs. Use plenum-rated cable

for applications where cable is to be run above the false

(suspended) ceiling in the air circulation space.

Allow some slack wire for servicing the cables and for

plugging the cable into an adjacent slot for

troubleshooting.

Wiring the readers

1. Install the reader in accordance with the

manufacturer’s instructions.

2. Run the appropriate cable from the reader to the

controller. Bring each reader cable through the

appropriate knockout hole in the controller cabinet.

3. Remove eight inches of insulating material from the

cable. Unwrap shielding and tie all shields together.

Connect the communications cable shield to the

ground nut adjacent to the cable entrance knockout

of the cabinet enclosure. For more details, see Figure

Caution: The 8RP Board has built-in pull-up resistors. Do

not install the external pull-up resistors supplied with the

GE Proximity Readers.

4. Depending on your configuration, attach the

appropriate wires to the appropriate screw terminal

on the 8RP Board as shown in Figure 3, Figure 4, and

Figure 5. Refer to Table 6 for connector pinouts.

Pairing of cables is very important. Refer to the

examples in Table 6.

5. To ensure proper function when using two 8RP

Boards in the M5 and M3000 controllers, the second

8RP Board should be wired directly to the Power

Communication Board, as shown in Figure 4

6. Label each cable end with the controller address

number and the device or reader number.

Figure 2: Typical installation using shielded cable/drain wire inside

and outside of the enclosure

Table 6: J2/J3/J4/J5 reader connector pinouts and typical pairing

Reader port Pin Signal name Typical wire color

1/3/5/7 1 +12 VDC Red

2 Ground Black

3 Reader data 1 Green

4 Door DO (reader LED) White

2/4/6/8 5 +12 VDC Red

6 Ground Black

7 Reader data 1 Green

8 Door DO (reader LED) White

4 of 6 P/N 460235001J • ISS 21MAR08

Wiring the door strike

One reader LED (door DO) is dedicated to each reader.

The reader LED (door DO) is used for the reader LED or for

an external door strike relay.

1. Install the door strike as required.

2. Wire the door strike to the external door strike relay.

The door strike relay is connected to +12 VDC (pin 1

and/or pin 5) and door DO (pin 4 and/or pin 8).

3. Install a protection diode across the relay and the

door strike. Use 1N4002, 1N4003, 1N4004 or

equivalent diodes for DC door strikes and Metal Oxide

Varistors (MOV) for AC door strikes. See Figure 3.

4. Protection diode or MOV and blocking diode are

required at all electronic door locks.

5. Install a blocking diode on the door DO (Reader LED)

line between the reader and the door strike relay.

Use 1N5817 diode, which is included with the reader.

The diode must be installed on the secure side of the

door in order to be UL compliant. See Figure 3.

Figure 3: Wiring 8RP to F/2F or supervised F/2F readers (2 state)

P/N 460235001J • ISS 21MAR08 5 of 6

Figure 4: Powering two 8RP Boards

Figure 5: Wiring 8RP to WIU-4/Wiegand readers

6 of 6 P/N 460235001J • ISS 21MAR08

Specifications

Reader power 12 VDC

Output One digital output (reader LED) per reader port,

12 VDC, 100 mA maximum per output point.

Cabling Multi-conductor, 20 AWG shielded pairs

Operating environment

Temperature

Humidity

35 to 122°F (2 to 50°C)

5% to 95% RH, noncondensing at 90°F (32°C)

Contacting customer support

You can reach customer support by phone from 8 a.m. to

7 p.m. EST, Monday through Friday.

GE Security

United States: 1-888-GE SECURITY (1-888-437-3287)

Asia: 852-2907-8108

Australia: 61-3-9259-4700

Europe: 48-58-326-22-40

Latin America: 305-593-4301

Inhaltsverzeichnis

Andere GE Sicherheitssystem Handbücher

GE 56789 Bedienungsanleitung

GE Advent Bedienungsanleitung

GE TX-6310-01-1 b Bedienungsanleitung

GE Simon XTi Bedienungsanleitung

GE Security Pro 1000 Bedienungsanleitung

GE 4 Series Bedienungsanleitung

GE CareGard Bedienungsanleitung

GE 45232 Bedienungsanleitung

GE Wireless Color Digital Home Monitoring Kit Bedienungsanleitung

GE SIMON XT Bedienungsanleitung

GE Simon XT V2 Bedienungsanleitung

GE VT71230-R3 Installationsanleitung

GE Concord Bedienungsanleitung

GE 13-949 Bedienungsanleitung

GE 45236 Bedienungsanleitung

GE AS272 Bedienungsanleitung

GE NX-10 Bedienungsanleitung

GE Concord 4 Bedienungsanleitung

GE Simon Security System Bedienungsanleitung

GE 45129 Bedienungsanleitung

GE NetworX Bedienungsanleitung

GE JSC1300 Bedienungsanleitung

GE 610 Bedienungsanleitung

GE 600-1064-95R b Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung