GE Druck ADTS 405 R/F Mk2 Bedienungsanleitung

www.gemeasurement.com

GE Data Classification: Public

Druck

ADTS 405 R/F Mk2

Air Data Test Set

Instruction Manual

ADTS HAND TERMINAL

POWERSUPPLY

100/120/230V~50/60Hz500VA

115~400Hz500VA

FUSES

T5.0A250VHRC

POWERSUPPLY24-30V

FUSES

500VA

T20A T32A

INTRODUCTION

This technical manual provides operating instructions for the Druck Air Data Test System ADTS 405

Mk 2 series.

SCOPE

This technical manual contains abrief description, operation and testing proceduresfor the user of this

equipment.

SAFETY

The manufacturer has designed this equipment to be safe when operated using the procedures

detailed in this manual:

• Do not use this equipment for any other purpose than that stated.

Incorrect use can prevent

theprotectiongiven by the equipment fromworking.

• See Product Safety and Installation Guide 124M8686, also supplied, for essential operating

and Safety instructions that must be followed to ensure safe operation.

• Use suitably qualified Technicians and good engineering practice for all procedures in this

publication.

*A qualified technician must have the necessary technical knowledge, documentation,

special test equipment and tools to carry out the required work on this equipment.

PRESSURE

Do not apply pressure greater than the maximum safe working pressure specified in this manual

when using the ADTS405 Mk 2 series.

TOXIC MATERIALS

There are no known toxic materials used in this equipment.

MAINTENANCE

The equipment must be maintained using the manufacturer’s procedures and should be carried out

by authorized service agents or the manufacturer’s service departments.

For technical advice contact GE or subsidiary manufacturer of this product.

MARKS AND SYMBOLS ON THE EQUIPMENT

For the list of approved GE service centers go to: www.gemeasurement.com

ASSOCIATED PUBLICATIONS

The following table lists the Druck publications referenced in this manual:

Symbol Description

This equipment meets the requirements of all relevant European safety

directives. The equipment carries the CE mark.

This symbol on the equipment indicates that the user should refer to the

user manual.

This symbol on the equipment indicates a warning and that the user should

refer to the user manual.

This symbol warns the user of the danger of electric shock.

Do not dispose of this product as household waste. Use an approved

organization that collects and/or recycles waste electrical and electronic

equipment. For more information contact your Customer Service using the

details shown at the back, or your local Government Office.

Safety and Installation Guide - Air Data Test Systems ADTS 405F/ 405R 124M8686

Calibration Manual -

Air Data Test System ADTS 405

K0199

IEEE 488 OPT 2 Manual -

Air Data Test System ADTS 405

K0154

SCPI IEEE 488 Manual -

Air Data Test System ADTS 405

K0157

User Manual -

Altimeter Encoder Option K0170

User Manual -

Line Switching Unit LSU 100/101

K0220

Operating and Communications Manual -

Line Switching Unit LSU Series

K0223

ABBREVIATIONS

The following abbreviations are used in this manual; the abbreviations are the same in the singular

and plural.

Abbreviation Description

A Ampere

abs Absolute

a.c. Alternating current

ALT Altitude

CAS Calibrated airspeed

d.c. Direct current

e.g. For example

EOC End ofconversion

EPR Engine pressureratio

EPROM Electrically programmable read only memory

etc. And soon

Fig. Figure

ft Foot

g Gauge

Hg Mercury

Hz Hertz

IAS Indicated airspeed

i.e. That is

IEEE 488 Institute of Electrical and Electronic Engineers standard 488 data

in inch

kg Kilogram

LED Light emitting diode

(M) Magnesium alloy

m Meter

mA Milliampere

max Maximum

mbar Millibar

mV Millivolts

No. Number

N.m. Newton meter

Para. Paragraph

Ps Static pressure

psi Pounds per squareinch

Pt Total pressure(pitot)

Qc Differential pressure Pt-Ps

QFE Local atmospheric pressure

QNH Barometric pressure at sea level

ROC Rate ofclimb

Vc Calibrated velocity

Vt True velocity

+ve Positive

-ve Negative

°C Degrees Celsius

Abbreviation Description

GLOSSARY

The terminology used in this manual is specific and individual interpretation must not be

introduced. The terms are defined as follows:

Item Description

Adjust To bring to a more satisfactory state; to manipulate controls, levers, linkages, etc. to

return equipment from an out-of-tolerance condition to an in-tolerance condition.

Align To bring into line; to line up; to bring into precise adjustment, correct relative

position or coincidence.

Assemble To fit and secure together the several parts of; to make or form by combining parts.

Calibrate To determine accuracy, deviation or variation by special measurement or by

comparison with a standard.

Check Make a comparison of a measure of time, pressure, temperature, resistance,

dimension or other quality with a known figure for that measurement.

Disconnect To detach the connection between; to separate keyed or matched equipment parts.

Dismantle To take apart to the level of the next smaller unit or down to all removable parts.

Ensure To confirm that a proper condition exists; to find out with certainty.

Examine To perform a critical visual observation or check for specific conditions; to test the

condition of.

Fit Correctly attach one item to another.

Inspect Review the work carried out by Specialists to ensure it has been performed

satisfactorily.

Install To perform operations necessary to properly fit an equipment unit into the next

larger assembly or system.

Maintain To hold or keep in any particular state or condition especially in a state of efficiency

or validity.

Operate Ensure that an item or system functions correctly as far as possible without the use

of test equipment or reference to measurement.

Readjust To adjust again; to move back to a specified condition; to bring back to an in-

tolerance condition.

Reconnect To rejoin or refasten that which has been separated.

Refit Fit an item which has previously been removed.

Remove To perform operations necessary to take an equipment unit out of the next larger

assembly or system. To take off or eliminate. To take or move away.

Repair To restore damaged, worn out or malfunctioning equipment to a serviceable, usable

or operable condition.

Replace Remove an item and fit a new or a serviced item.

Reset To put back into a desired position, adjustment or condition.

Service To perform such operations as cleaning, lubricating and replenishing to prepare for

use.

Test Ascertain by using the appropriate test equipment that a component or system

functions correctly.

RETURNED GOODS PROCEDURE

If the unit is unserviceable and requires a repair return to a GE Service Centre. Contact the GE

Service Centre, either by 'phone, fax or e-mail to obtain a Returned Goods Authorization (RGA)

number, providing the following information:

• Product (i.e. ADTS 405)

• Pressure medium (i.e. air, nitrogen)

• Serial number

• Details of defect/work to be undertaken

• Operating conditions

SAFETY PRECAUTIONS

See Safety and Installation Guide 124M8686

Note: Do not use unauthorized sources to service this equipment as this will affect the

warranty and may not guarantee further performance.

PRESSURE UNITS AND CONVERSION FACTORS

Pressure units Factor (hPa) Pressure units Factor (hPa)

mbar 1.0 cmH2O @ 20°C 0.978903642

bar 1000.0 mH2O @ 20°C 97.8903642

Pa (N/m2)0.01 kg/m

20.0980665

hPa 1.0 kg/cm2980.665

kPa 10.0 torr 1.333223684

MPa 10000.0 atm 1013.25

mmHg @ 0°C 1.333223874 psi 68.94757293

cmHg @ 0°C 13.33223874 lb/ft20.4788025898

mHg @ 0°C 1333.223874 inH2O @ 4°C 2.4908891

inHg @ 0°C 33.86388640341 inH2O @ 20°C 2.486413

mmH2O @ 4°C 0.0980665 inH2O @ 60°F 2.487641558

cmH2O @ 4°C 0.980665 ftH2O @ 4°C 29.8906692

mH2O @ 4°C 98.0665 ftH2O @ 20°C 29.836983

mmH2O @ 20°C 0.097890364 ftH2O @ 60°F 29.8516987

Unit Conversion

To convert FROM pressure Value 1(in pressure Units)1 TO pressure Value 2 in pressure

Units: Calculate as follows:

Value 2 = Value 1 x Factor 1 ÷ Factor 2

Inhaltsverzeichnis

Andere GE Prüfgeräte Handbücher

GE NOVA Stücklistenhandbuch

GE EVT-Pro 2.0 Bedienungsanleitung

GE Druck DPI 832 Bedienungsanleitung

GE PACE5000 Bedienungsanleitung

GE ADTS 542 Bedienungsanleitung

GE EVT-Pro Bedienungsanleitung

GE RTT Bedienungsanleitung

GE Druck UPS-III Bedienungsanleitung

GE Druck ADTS 505 Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE Mentor EM Bedienungsanleitung

GE Druck DPI 620 Bedienungsanleitung

GE PK-2 Bedienungsanleitung

GE Druck UPS-III Bedienungsanleitung

GE ADTS552F Bedienungsanleitung

GE Druck ADTS 2 Series Bedienungsanleitung

GE Druck ADTS 405 Bedienungsanleitung

GE XL VU Bedienungsanleitung

GE Druck DPI 620-IS Bedienungsanleitung

GE Druck DPI 620 Bedienungsanleitung

GE ADTS552F Einrichtungshandbuch

GE DPI620G-IS Bedienungsanleitung

GE Druck ADTS 2 Series Gebrauchs- und Pflegehandbuch

GE Druck ADTS 542F Einrichtungshandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung