GE Druck DPI612 Bedienungsanleitung

Measurement and Control

subject to change without notice. GE is a registered trademark of General

Electric Company. Other company or product names mentioned in this

document may be trademarks or registered trademarks of their respective

companies, which are not affiliated with GE.

Druck DPI612

Portable Pressure Calibrator

Safety and Quick Start guide – 109M0089

Safety and Quick Start Guide Druck DPI612

Page 2of 20 [EN] English – 109M0089

DPI612: Pressure Calibrator (Figure 1)

DPI612-PFX (pFlex Pneumatic Calibrator):

-950 mbar to 20 bar (-13.5 to 300 psi)

DPI612-PFP (pFlexPro Pneumatic Calibrator):

-950 mbar to 100 bar (-13.5 to 1500 psi)

DPI612-HFP (hFlexPro Hydraulic Calibrator):

0 to 1000 bar (0 to 15000 psi)

Operating Temperature Range:

-10 °C to +50 °C (+14 °F to +122 °F)

+10 °C to +30 °C (optimized calibration specification)

0 °C – 40 °C with optional mains power supply

Storage Temperature: -20 °C to +70 °C (-4 °F to +158 °F)

Humidity: 0 to 90 % Relative Humidity (RH)

Non-condensing

Power Supply: 100 – 260 V +/-10 %, 50 / 60 Hz AC, Output DC V=5 A,

1.6 A, CATII of IEC60364-4-443

Altitude: Up to 2000 m

Batteries (Rechargeable): LiIon 14.1Wh GE Part number: CC3800GE

Nominal voltage 3.7V 3800mAh Charge temperature: 0° to 40°C (32°

to 104°F) Discharge temperature: -10° to 60°C (14° to 140°F). Note: For

best battery performance, keep the temperature less than 60°C

(140°F).

Batteries (Non-rechargeable): 8 × AA Alkaline

Pressure Leak rates:

DPI612-PFX = 0.01 bar/min at 20 bar

DPI612-PFP = 0.02 bar/min at 100 bar

DPI612-HFP = 1 bar/min at 1000 bar

Vacuum Leak rates:

DPI612-PFX = 0.005 bar/min at 95% Vacuum

DPI612-PFP = 0.005 bar/min at 95% Vacuum

DPI612-HFP = n/a

Recommended Pressure Modules (PM620)

DPI612-PFX: 2 to 20bar (3 to 300 psi)

DPI612-PFP: 20 to 100bar (300 to 1500psi)

DPI612-HFP: 200 to 1000bar (3000 to 15000psi)

Safety and Quick Start Guide Druck DPI612

Page 3of 20 [EN] English – 109M0089

GENERAL WARNINGS

•Before using this instrument, read and understand the “Safety” section,

the user manual and the instructions for the accessories / options /

equipment you are using it with.

•Read and understand the applicable local safety procedures.

•It is dangerous to ignore the specified warnings.

•It is dangerous to ignore the specified limits for the instrument or to use

the instrument when it is not in its normal condition. Use the applicable

protection and obey all safety precautions.

•Do not use the instrument in locations with explosive gas, vapor or dust.

There is a risk of an explosion.

•Do not use damaged equipment and use only original parts supplied by

the manufacturer.

ELECTRICAL WARNINGS

•To prevent electrical shocks or damage to the instrument, do not connect

more than 30 V between the terminals, or between the terminals and the

ground (earth).

•This instrument uses a Lithium Ion rechargeable battery pack or optional

standard AA size batteries. To prevent an explosion or fire, do not short

circuit, crush or disassemble.

•To prevent battery leakage or heat generation, only use the GE specified

battery, power supply and battery charger. Note: The power supply is only

specified for operation in the temperature range 0 to 40 °C (32 to 104 °F).

Safety and Quick Start Guide Druck DPI612

Page 4of 20 [EN] English – 109M0089

CAUTIONS

•To prevent damage to the display, do not use sharp objects on the touch-

screen.

•Removal of power without appropriately shutting down the DPI612 can

lead to loss of date and time; if it happens re-set the date and time upon

re-start.

•To prevent damage to the DPI612 and PM620 module, only use it within

the specified pressure limit.

•To prevent damage to the instrument, do not allow dirt into the pressure

mechanism. Clean any attached equipment before connection.

•This instrument is not suitable for permanent outdoor installation.

1. OVERVIEW

Figure 1

The DPI612 is a battery-powered instrument for electrical measure and source

operations. You can use the touch-screen to display the different parameters.

The DPI612 instrument measures and displays, via user interchangeable

pressure modules, Pneumatic or Hydraulic Pressure/ Vacuum generated by

the instrument. The type and range of pressure generation is dependent on

the model selected.

DPI612- PFX

DPI612- PFP

DPI612- HFP

Safety and Quick Start Guide Druck DPI612

Page 5of 20 [EN] English – 109M0089

Figure 2

Item 2.1

5.1

3.1

2.1

3.1

Safety and Quick Start Guide Druck DPI612

Page 6of 20 [EN] English – 109M0089

Figure 3

Safety and Quick Start Guide Druck DPI612

Page 7of 20 [EN] English – 109M0089

1.1 PARTS LIST

Item

No. Description

ON or OFF button.

PFX only: Pneumatic volume adjuster.

2.1

PFP, HFP models only: Volume adjuster wheel with fold-in handle.

Pump mechanism.

3.1

PFX, PFP models only: Pressure/vacuum selector to set the pump operation: pressure (+),

vacuum (-).

Test port: To attach the device under test.

Pneumatic pressure release valve to release pressure in the system.

5.1

PFP models only: Pneumatic refill valve. Close it to seal off the device pressure and refill

the pressure mechanism.

CH1 connectors for: Voltage (V); Current (mA+, mA-); Switch operation.

Isolated CH2 connectors for: Voltage (V); 24 V loop power supply (24 Vo).

Liquid Crystal Display (LCD): Color display with touch-screen. To make a selection, lightly

tap on the applicable display area.

Optional accessory (not shown): Pressure connection for a relief valve (PRV). A blanking

plug is standard.

Pressure and electrical connections for a PM620 module (not shown):

DPI612 models PFX and PFP: Seal the pressure connection with a blanking plug (Part:

IO620-BLANK) or a PM 620 module.

DPI612 HFP models only: The pressure connection seals itself.

HFP models only: Hydraulic refill valve (not shown):Close it to seal off the device pressure

and refill the pressure mechanism with fluid.

Hand straps

+5 V DC power input socket. This supply also charges the optional battery pack.

USB type A connector for connections to external peripherals (USB flash memory or

optional external modules).

USB mini-type B connector for communication with a computer.

Safety and Quick Start Guide Druck DPI612

Page 8of 20 [EN] English – 109M0089

2. EXTERNAL PRESSURE CONNECTION

Use an applicable method to seal the external pressure connections, and then

tighten to the applicable torque.

Maximum torque: ISO 228/1, 1/8 NPT: 35 Nm (26 lbf.ft)

ISO 228/1, G1/8: 25 Nm (18.4 lbf.ft)

Attach the pressure adaptor to the DPI612 and tighten to finger tight.

3. DPI612 PRE-CALIBRATOR – START OPERATIONS

3.1 Install the rechargeable battery

1. Remove the battery cover by unscrewing the retaining screw and lifting the

cover upwards.

2. Insert the CC3800GE rechargeable battery into the compartment as shown

in Figure 4.

3. Refit the battery cover by locating the lugs of the cover (A) at an angle into

the slots and close the compartment as shown in Figure 4.

4. Refit the battery cover retaining screw.

Figure 4

Safety and Quick Start Guide Druck DPI612

Page 9of 20 [EN] English – 109M0089

4. POWER MODES

4.1 Power ON (See Figure 3)

From OFF – momentarily press the power button until the GE logo appears.

4.2 Power OFF

Press and Release the Power Button:

Select SWITCH OFF from the POWERDOWN OPTIONS window displayed.

Figure 5

Notes:

•SWITCH OFF can also be achieved by Pressing and holding the power

button until the screen is blank.

•Use Power OFF to preserve the battery capacity when the instrument is

not in use for extended periods of time.

4.3 Standby Mode

Press and Release Power button:

Select GO TO STANDBY from the POWERDOWN OPTIONS window displayed.

Note: Use Standby mode between the jobs to provide a quick start-up.

4.4 Power up from Standby Mode

When powered up from the standby mode, instrument always opens the last

screen shown before going to standby mode.

Safety and Quick Start Guide Druck DPI612

Page 10 of 20 [EN] English – 109M0089

5. DASHBOARD NAVIGATION

The application DASHBOARD allows quick selection of a function without

menus or special keys. The DASHBOARD icons represent the functional

applications of the DPI612, for example, the CALIBRATOR application. Touch

the appropriate icon to start the application.

When more choices are available than shown on the display, swipe a finger up

or down, left or right to scroll.

FIGURE 6

1) Swipe from right to left.

2) Touch the TASK menu.

3) Touch the TASK.

Figure 7

Andere Handbücher für Druck DPI612

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere GE Prüfgeräte Handbücher

GE Druck DPI612 Bedienungsanleitung

GE Druck ADTS 542F Einrichtungshandbuch

GE DPI620G-IS Bedienungsanleitung

GE PACE5000 Bedienungsanleitung

GE Druck ADTS 405 R Mk2 Bedienungsanleitung

GE EntelliGuard G Bedienungsanleitung

GE Druck DPI611 Bedienungsanleitung

GE Druck DPI 620 Bedienungsanleitung

GE ADTS552F Einrichtungshandbuch

GE Mentor EM Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE Druck DPI 880 Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE ADTS 542 Bedienungsanleitung

GE EntelliGuard Bedienungsanleitung

GE ADTS552F Bedienungsanleitung

GE PACE5000 Bedienungsanleitung

GE Druck DPI 610 Bedienungsanleitung

GE Druck ADTS 2 Series Bedienungsanleitung

GE NOVA Stücklistenhandbuch

GE Multilin EPM 7000 Bedienungsanleitung

GE K0341 Bedienungsanleitung

GE TVRMS2 Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung