GE FTP 1000 - Security Concord LCD Touchpad Bedienungsanleitung

123

456

789

Stay

Away

Disarm

Quick

Exit

FTP-1000 Touchpad/Display

Installation Manual

This document may not be copied or otherwise reproduced, in whole or in part, except as

specifically permitted under US and international copyright law, without the prior written

consent from GE.

Document number/revision: 466-2231A (December 2005).

Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. GE ASSUMES

NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND SPECIFICALLY DISCLAIMS ANY

LIABILITIES, LOSSES, OR RISKS, PERSONAL OR OTHERWISE, INCURRED AS A CONSEQUENCE,

DIRECTLY OR INDIRECTLY, OF THE USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS

DOCUMENT. FOR THE LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US

ONLINE AT WWW.GESECURITY.COM.

This publication may contain examples of screen captures and reports used in daily operations.

Examples may include fictitious names of individuals and companies. Any similarity to names

and addresses of actual businesses or persons is entirely coincidental.

Trademarks and patents GE and the GE monogram are registered trademarks of General Electric.

FTP-1000 touchpad/display product and logo are registered trademarks of GE Security.

Other trade names used in this document may be trademarks or registered trademarks of the

manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user

documentation. For the latest product information, contact your local supplier or visit us online

at www.gesecurity.com.

FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications.

You are cautioned that any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

Preface

This is the GE FTP-1000 Installation Manual for model 600-1020. This document includes an overview of the

product and detailed instructions explaining:

• how to install the touchpad; and

• how to program the touchpad.

There is also information describing how to contact technical support if you have questions or concerns.

To use this document effectively, you should have the following minimum qualifications:

• a basic knowledge of security systems and components; and

• a basic knowledge of electrical wiring and low-voltage electrical connections.

Read these instructions and all ancillary documentation entirely before installing or operating this product.

The most current versions of this and related documentation may be found on our website. Refer to Online

publication library on page 9 for instructions on accessing our online publication library.

Note: A qualified service person, complying with all applicable codes, should perform all required hardware installation.

Conventions used in this document

The following conventions are used in this document:

Safety terms and symbols

These terms may appear in this manual:

Bold Menu items and buttons.

Italic Emphasis of an instruction or point; special terms.

File names, path names, windows, panes, tabs, fields, variables, and other GUI elements.

Titles of books and various documents.

Blue italic (Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses.

Monospace Text that displays on the computer screen.

Programming or coding sequences.

CAUTION: Cautions identify conditions or practices that may result in damage to the equipment or other property.

WARNING: Warnings identify conditions or practices that could result in equipment damage or serious personal injury.

FTP-1000

Installation Manual

Product overview

The FTP-1000 lets you control the operation of compatible security systems (see Table 4 on page 10).

The large display provides easy to read messages to indicate the current status of the system. The touchpad

includes police, fire, and auxiliary panic buttons that can be activated anytime. A built-in speaker provides

alarm, status, and button-press sounds. A swing-down door reveals a label with basic system operating

commands. The door can be removed by simply opening it past its stop point. The door can also be reattached

later if desired.

Tools and equipment needed

• 4-conductor, 22- or 18-gauge wire

• Screwdriver

• #6 screws and anchors (included)

• Panhead screws for gang box installation

• Saw or utility knife for cutting wallboard

Installation

Use the following instructions to install and wire your touchpad.

Guidelines

• Mount the touchpad in an environmentally controlled area (32 to 120°F or 0 to 49°C).

• When mounting the touchpad, allow at least 3 inches below it for the swing-down cover.

• Do not exceed the maximum available power. See the panel installation instructions for maximum

available power.

•Table 1 describes the power used by the touchpad.

•Table 2 describes the maximum wire lengths allowed between the touchpad and the panel.

Mounting plate installation

To install the mounting plate, do the following:

1. Separate the mounting plate from the touchpad by first loosening the screw, then lift the touchpad

away from the mounting plate (see Figure 1).

Figure 1. Mounting plate screw

Table 1. Touchpad power usage

Current (mA) Conditions

75 Maximum alarm current with the buzzer sounding and the

touchpad illuminated from a button press

50 Typical operation

12 Power saving mode (no panel AC power)

Table 2. Maximum touchpad wire lengths

Wire gauge (unshielded or shielded) Max touchpad wire length between touchpad and panel

18 750 feet

22 300 feet

Mounting plate screw

FTP-1000

Installation Manual

2. For wall mounting, place the mounting plate on the wall and mark the mounting holes (see Figure 2).

Be sure to leave a 3-inch clearance below for the touchpad door to open.

Figure 2. Mounting hole locations

3. Insert anchors into the wall at the marked locations where studs are not present.

4. Align the mounting plate holes with the wall or gang box screw holes and secure the back plate using

the screws provided.

Note: Do not overtighten screws or the mounting plate may bind and prevent the touchpad from mounting properly.

5. For wall-mount installations, cut a hole in the wall behind the mounting plate to pull the wiring cable

through.

Wiring the touchpad to the panel

To wire the touchpad to the panel, do the following:

1. Remove panel AC and backup battery power.

2. Run a 4-conductor, 18- to 22-gauge wire from the panel to the touchpad location (see Table 2 on

page 3).

3. Connect the touchpad +12V, Bus A, Bus B, and GND terminals to the matching panel terminals

(Figure 3 on page 5).

Note: The wiring should extend from the right side of the connector.

Figure 3. Touchpad wiring connections

Attaching the touchpad to the mounting plate

Align the tabs at the top of the mounting plate with the slots on the touchpad and swing the touchpad bottom

toward the mounting plate. Gently tighten the screw into the bottom of the touchpad.

Power-up and bus communication

After making all wiring connections from the touchpad to the panel, you are ready to power up the panel and

verify correct communication between the touchpad and the panel. Upon power-up, the panel scans the bus for

connected devices and automatically learns the unit number of each bus device.

Note: If you plan to install systems with no alphanumeric touchpads, we recommend that you keep an alphanumeric

touchpad with you, specifically for installer programming. This touchpad can be quickly connected and disconnected

from the header pins on the lower-left portion of the panel, just above the terminal strip.

To power up the panel and verify bus communication:

1. Verify that all wiring between the panel and touchpad is correct.

2. Connect the panel battery and plug in the panel transformer. The touchpad should display BUS SCAN,

then show a time display with the PRESS STATUS prompt in the upper-left corner.

Note: If the touchpad does not power up (show any display) or respond as described above, unplug the panel AC

transformer and disconnect the backup battery. See Troubleshooting on page 9 for more information.

GND

Bus B

Bus A

+12V

FTP-1000

Installation Manual

Testing

Use the following procedures to test the touchpad for display function, button function, and system operation.

Test touchpad display function

Press and hold the 4, 5, and 6buttons together for about three seconds, then release them.

The touchpad cycles though all text messages, then returns to the time display.

Test button function

To test the button functions, do the following:

1. Press and hold the 7, 8, and 9buttons together for about three seconds, then release them. The display

should go blank.

2. Press each touchpad button to display a different string of letters or numbers for each button. For

example, 11111111111, AAAAAAAAAAA, etc. Pressing *displays Es and pressing #displays Fs. After

about 15 seconds of no touchpad activity, the touchpad returns to the time display.

Test system operation

Testing the system operation requires you to perform some standard operations to ensure that they work

properly.

To test the system’s operation, do the following:

Arm/disarm the system, activate the touchpad panics, bypass sensors, and turn chime on/off to verify correct

operation.

Note: You must enable the touchpad panic buttons in order to activate them. Please see the panel installation instructions for

more information.

Refer to the panel’s user manual for complete system operating instructions and user programming procedures.

CAUTION: Contact the central monitoring station before activating alarms, to avoid dispatching local police and fire

departments

Adjusting display brightness

You can adjust the background lighting (provided by yellow LEDs) of each touchpad individually to help

compensate for lighting conditions at the touchpad location. The brightness adjustment lightens or darkens the

display background and button lighting.

Adjust display background brightness

To adjust display background brightness, do the following:

1. Enter user programming mode by pressing 9+ system master code. The display shows SYSTEM MENU,

then TIME - dATE.

2. Press Aor Buntil the display shows OPTIONS, then press #. The display shows dOWnLd ON.

3. Press Aor Buntil the display shows BRIgHT 2 (default setting).

4. Enter a setting from 0(LEDs off) to 3(brightest), then press #. The display shows the new setting.

5. Exit user programming by pressing:

•*+ 4+ #for Concord Express panels,

•or*+ 00 + #for Concord panels.

FTP-1000

Installation Manual

Changing chime and trouble beep tones

The frequency (pitch) of chime and trouble beep tones from each touchpad can be adjusted to a more desirable

or distinct tone, and to compensate for hearing impaired persons.

Note: Chime and trouble beep tones sound (using the default frequency) during, or within 15 seconds of any button activity at

that specific touchpad.

Change status tone pitch

To change the status tone pitch, do the following:

1. Press and hold the *and 0buttons together until you hear a steady tone, then release the buttons.

2. Press and hold 1to lower the pitch or press and hold 2to raise the pitch.

3. Release the button when the desired pitch is heard. After about 15 seconds of no touchpad activity, the

steady tone stops sounding.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Touchscreen Handbücher

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung