GE 24962 Bedienungsanleitung

Universal Remote

Instruction Manual

24962

Congratulations on your purchase of the 24962

Universal Remote Control. The 24962 is one of the

most easy to use remote controls available today.

With the 24962, juggling multiple remote controls is

a thing of the past! Your 24962 controls up to three

devices, including the most popular brands of TV,

DVD, Satellite, Cable, etc.

Note: Some functions from your original remote

may not be controlled by this remote. Use the

original remote, if available, to control such

functions. Sometimes buttons other than described

in these instructions may actually perform the

function. For example, the CHAN and VOL

buttons might be used to navigate through menu

choices. We recommend you experiment with the

remote to identify if such situations pertain to your

equipment.

The 24962 is easy to use, easy to program, and

it gives you total control—at the touch of your

ngertips!

 TableofContents

Setup ..................................................................... 3

Battery Installation ............................................ 3

Battery Saver .................................................... 3

Code Saver ...................................................... 3

Code Setup ...................................................... 3

Button Functions.................................................... 4

Shift .................................................................. 6

Direct Code Entry .................................................. 7

Code Search.......................................................... 8

Code Identication ................................................. 9

Using Your Remote.............................................. 10

Controlling Devices with Separate

Power On and Off ........................................... 10

Controlling Combo Devices ............................ 10

DVR/DVD/ Punch-Through ............................ 10

Volume/Mute Control and Punch-Through ..... 11

Setting All Volume/Mute Control

to any one Mode ............................................. 11

Setting any Mode for its own

Volume/Mute Control ...................................... 12

Troubleshooting ................................................... 13

Battery Installation

1. On the back of the remote, push down on the

tab and lift the cover off.

2. Match the batteries to the + and - marks inside

the battery case, then insert 2 AAA Alkaline

batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons

are depressed more than 30 seconds. This will

save your batteries should your remote get stuck in

a place where the buttons remain depressed (e.g.,

between the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote.

If buttons are pressed without batteries in the

remote, all codes will be lost.

Code Setup

The SETUP button is used to setup the remote.

You can either setup the remote using the code

for your brand of product, from the code tables (on

separate sheet), or you can search through the

library of codes until you nd a code that works for

your product. Please refer to “Code Search” page

8 for more information on using the code search

feature to learn how to search through the library

of codes for your products. NOTE: You can store

any kind of code under any mode (except TV). I.e.,

you can store a DVR code under the SAT/CBL

button, or a cable code under the DVD button, etc.

However, you can only store TV codes under the

TV button.

 Setup

MUTE Turns off the

TV sound while the

picture remains.

OK Selects menu

items for the device

you are controlling.

INFO button brings up

DVD Display or Control

Menu for Chapter/

Track/Title number,

Time remaining/elapsed

indication, system

information, etc.

Selects the on-screen

menu.

RECORD, PLAY, STOP,

REW, FF, PAUSE oper-

ate your DVD or DVR

even when the remote

is set to operate the TV.

Also operates DVD/DVR

Scan -/+.

Some buttons on the remote might have functions that

are referred to by different names on the device you are

controlling. E.g., PREV. CH may be called RECALL,

or ENTER may be called DISPLAY. These differences

depend on the brand and model of your product. Also,

this remote can only operate features that exist on your

product. E.g., your product must have PREV. CH ability

for the PREV. CH button to operate this feature.

TV, DVD, SAT/CBL Selects

product to be operated.

 ButtonFunctions

SETUP For setup.

SHIFT Accesses

shifted functions.

DOT Used to

select digital chan-

nels, e.g., 2.3.

VOLUME UP/DOWN

Changes the volume

level of the product,

normally the TV.

NUMBERS

Enter numbers for direct

channel selection. Some

products require ENTER

to be pressed after

channel selection.

ON-OFF Turns

device On or Off.

 ButtonFunctions,cont.

Note: The REC button must be pressed TWICE to record

from your DVR. For some brands of DVRs, you might

need to press the REC button once, then press it again

for three seconds.

ENTER

For some TV models,

used after direct

channel number

entry to immediately

change to the

selected channel.

Red Indicator

Lights when any

button is pressed.

INPUT

For some TVs, press

repeatedly to select

from available viewing

sources (antenna, cable

box, DVD, etc.).

PREV. CH Returns to

the previously

selected channel.

EXIT Exit On-Screen

Menus and/or Return

to previous On

Screen selection.

CHANNEL Up/Down

Changes the channels.

Press SHIFT (Setup) prior to the shifted key func-

tion, e.g., for MENU - press and release SHIFT

(Setup) then MENU (Info).

UP - press and release SHIFT then UP (Chan+).

DOWN - press and release SHIFT then DOWN

(Chan-).

LEFT - press and release SHIFT then LEFT (Vol-).

RIGHT - press and release SHIFT then RIGHT

(Vol+).

OK - press and release SHIFT then OK (Mute).

EXIT - press and release SHIFT then EXIT (Prev.

Ch).

The red indicator blinks for each key press.

 SHIFTFunction

 DirectCodeEntry

Write your codes down here for easy reference

later.

1. Press and hold the SETUP button until

the red indicator stays on, then release

the SETUP button.

2. Press and release the desired mode

button (TV, DVD, etc.). The red indicator

blinks, then stays lit.

3. Enter the 4-digit code

from the code tables

(on separate sheet).

Note: after a valid code

entry, the red indicator

turns off. For an invalid

code, the red indicator

ashes.

4. With your device on, press ON/

OFF. If the device turns off, no

further programming is required.

Note: If some buttons do not

operate your equipment, try one

of the other codes for your brand.

Device Device stored Code

TV TV

DVD

SAT/CBL

 CodeSearch

If your device does not respond after you have

tried all the codes for your brand, or if your brand is

not listed, try searching for your code by following

these steps.

1. Manually turn on the device (TV, DVD, etc.) to

be controlled.

2. Press and hold the SETUP button until

the red indicator stays on, then release

the SETUP button.

3. Press and quickly release the desired

mode button (TV, DVD, etc.). The red

indicator blinks off once.

4. Press the CHAN+ button

repeatedly (up to 300 times)

until the device to be controlled

changes channel. The red

indicator blinks off with each

button press. If you accidentally overshoot

the code required, press the CHAN- button to

backtrack through the library until the device

changes channel. Pressing CHAN+ changes

direction to forward again.

5. Press and release ENTER to install the

code.

Most users will store DVD codes under the DVD button,

and Satellite or Cable codes under SAT/CBL. If (for ex-

ample) you want to store a DVR code under SAT/CBL,

rst follow the procedure for Direct Code Entry (page

8) and press SAT/CBL in step 2 of Direct Code Entry,

then enter ANY DVR code in step 3 of Direct Code Entry.

Then follow the steps above for Code Search.

Note: If the device does not have a CHAN+ button, use

PLAY (DVD/DVR/VCR only) or POWER instead. Code

Search starts from the currently stored 4 digit number

under that mode. Sometimes the rst code that “works”

with your device may only allow limited functionality

(e.g., the MENU button might not work). There may be

a code that performs more functions. Continue the code

search process until the best code is found.

 CodeIdentication

The Code Identication Feature allows you to

identify the 4-digit library code stored under your

device key. For example, if you want to nd out

what 4-digit code is stored under your TV device

key, follow the six steps below:

1. Press and hold the SETUP button until

the red indicator stays on. Release the

SETUP button.

2. Press and release the desired mode

button (TV, DVD, etc.). The red

indicator blinks, then stays lit.

3. Press and release the SETUP button.

The red indicator blinks once and

remains lit.

4. To nd the rst digit for

the code stored under

the mode key pressed

in step 2, press each

numeric key from 0-9 in

turn. The number that

causes the indicator

light to blink is the rst

digit in your code.

5. To nd the second digit, repeat step 4.

6. Repeat step 4 again to nd the third and fourth

digits. This time the red indicator turns off and

stays off.

 UsingYourRemote

Controlling Devices with Separate

Power On and Off Buttons

Some GE, RCA and ProScan models require

you to press the device button for more than one

second to turn the device on and the POWER

button to turn the device off.

Controlling Combo Devices

Some Combo devices (e.g., TV/DVR, TV/DVD,

DVD/DVR, etc.) will require you to set up two

different Mode buttons to control both parts of the

Combo device. For example, if you have a TV/

DVD Combo, you might need to set up one code

under the TV button to control the TV part AND a

separate code (under any other Mode button) to

control the DVD part.

DVR/DVD Punch-Through

This remote allows the 6 DVD/VCR transport

buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND,

and REC) to Punch-through from any Mode

programmed with TV, SAT or Cable codes to the

last DVD, or VCR programmed Mode you used,

i.e., the transport keys control your DVD or VCR

player even when you are in TV, SAT or Cable

mode. If you use a SAT/DVR, Cable/DVR, etc., you

may want to disable this Punch-through feature

to allow the transport keys to control your DVR

device. The following steps will disable the punch-

through feature:

1. Press and hold SETUP until the red indicator

stays on, then release the SETUP button.

2. Press and hold PAUSE until the red indicator

turns off, then release the PAUSE button. The

PAUSE button needs to be held held for about

3 seconds before the red indicator turns off.

The punch-through feature can be enabled again

by repeating the above steps.

Inhaltsverzeichnis

Andere GE Universalfernbedienung Handbücher

Beliebte Universalfernbedienung Handbücher anderer Marken

Pronto

Pronto Peel Bedienungsanleitung

Radio Shack

Radio Shack Wireless Remote Control System Bedienungsanleitung

AUVIO

AUVIO Universal Home Theater Remote Bedienungsanleitung

Philips

Philips Icon SRU4106 Bedienungsanleitung

THOMSON

THOMSON ROC4309 Bedienungsanleitung

Philips

Philips pm625S Bedienungsanleitung

RCA

RCA RCU600WMS - Universal Remote Control Bedienungsanleitung

Blackweb

Blackweb BWB17AV002 Bedienungsanleitung

Marmitek

Marmitek DoorGuard 300 Bedienungsanleitung

Chunghop

Chunghop RM-L618 Bedienungsanleitung

Anderic

Anderic KTN828 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Bedienungsanleitung

Medion

Medion E74023 Bedienungsanleitung

intensity

intensity RM02A Bedienungsanleitung

Sky

Sky MY Bedienungsanleitung

RCA

RCA RCU600M - Universal Remote Control Bedienungsanleitung

Savant

Savant SUR-0500 Kurzanleitung

GDI

GDI GDI-WT2K Bedienungsanleitung