GE 33705 Bedienungsanleitung

Universal Remote

Instruction Manual

33705 | 33706 | 33707 | 33708 | 34456 | 34708 | 24991

| 27985

7252

vers3 | 3/17

Congratulations on your purchase of this GE-branded

Universal Remote. This remote is capable of operating

thousands of audio/video devices including TVs, DVD

players, cable, satellite receivers and more!

Introduction.......................................................................................... 2

Setup........................................................................................................ 3

Button Functions ............................................................................... 4

Programming Your Remote......................................................... 6

Direct Code Entry....................................................................... 6

Auto Code Search...................................................................... 8

Controlling Combo Devices.................................................. 9

Using your Remote.........................................................................10

Using Shift....................................................................................10

Master Volume Feature........................................................11

Disabling Master Volume Feature...................................11

Code Identiﬁcation..................................................................12

Reset to Factory Settings.....................................................12

Troubleshooting...............................................................................13

Warranty..............................................................................................14

FCC Statement..................................................................................15

Table of Contents

Scan this to view

a helpful remote

setup video

http://www.byjasco.com/remote

SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

If you have any questions or would like

additional information please, visit our web site

www.byjasco.com, or contact our

Technical Support Group at 1-800-654-8483,

Monday-Friday 7:00am-8:00pm CST.

Setup

Your universal remote requires two (2) AAA batteries

(not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, pull down on

the textured surface and slide battery cover

downward to remove.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AAA batteries. Be sure to use

fresh batteries.

3. Position battery cover slightly below opening and

push upward to lock into place.

NOTE: If your remote stops operating properly, replace

the batteries with new ones.

Battery Precautions

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Always remove old, weak or worn-out batteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You have up to 10 minutes to change the batteries

in your remote without losing the codes you have

programmed.

Button Functions

2 1

Button Functions

1. Power - Turns devices ON/OFF

2. Red Indicator Light

3. TV, cbl, dvd, aux - Selects the device to control

4. Record, play, stop, rewind, fast forward, pause

5. Input - Selects video inputs; Guide (Shift mode)

Displays satellite or cable on-screen program

guide. Works as home function for Smart TVs and

streaming devices

6. Setup - Used to program the remote; Shift is

the alternate function of this button. Use the

Shift button to access the Menu, Guide and Exit

functions of your device. To enter the Shift mode

press this button once. To exit the Shift mode,

press the button again.

7. Channel Up/Down, Volume Left/Right -

Control channels and volume; Menu Navigation

(Shift mode)

8. Ok - Selects menu items for the controlled device;

Mute (Shift mode) mutes sound

9. Info - Displays on-screen show/content

information; Menu (Shift mode) Displays the

on-screen menu

10. Previous Channel - Returns to the previously

selected channel; Exit (Shift mode) Exit

on-screen menus

11. Numbers - Used for direct channel selection

12. Dot (•) - Used to select digital channels, e.g., 4.1

13. Enter - Some devices require Enter to be pressed

after channel selection

*AUX Button not available on model

number 34456, 24991 | 3-device

Universal Remote

Programming Your Remote

Your remote is designed to control multiple audio/video

devices. To use, you will need to program the remote for

your devices. There are two different methods you can

use to program the remote, Direct Code Entry or Auto

Code Search.

• The Direct Code Entry method is the recommended

method as it is the simplest and quickest method in

most cases.

• The Auto Code Search method searches through

all the codes in the remote to ﬁnd a code for

your device.

Note: this remote comes preprogrammed for Roku®boxes and

Samsung TVs. Press TV for Samsung TVs and strm for Roku boxes.

Direct Code Entry (Recommended)

1. Locate the Code List included with

your remote. Find the section for the

type of device you wish to control,

(for example TV, cbl, dvd, aux). Locate

the brand of your device and circle all

the remote codes for the brand.

2. Press and hold down the SETUP button

on the remote until the red light on the

remote control turns on. Release the

SETUP button. The red light will

remain on.

Note: The red light will either be a small light at the

top of the remote or the power ON/OFF button.

3. Press and release the device button on

the remote for the type of device you

wish to control, (for example TV, cbl,

dvd, aux). The red light will blink once

and remain on.

Note: Any of the device buttons on the remote can

be programmed to control any of your devices. For

example, you can use the CBL device button on

the remote to control a Satellite Receiver, Digital

Converter Box, Streaming Media Player or any

device category in the Code List.

4. Use the number buttons on the remote

to enter the ﬁrst 4-digit remote code

you circled in the Code List in Step 1.

Programming Your Remote

The red light will turn off after entering

the fourth digit.

5. Point the remote at the device. Test

the buttons on the remote to see if the

device responds as you would expect.

If the buttons do not operate the device,

return to Step 2 above and use the next

code that you circled for that device.

6. Repeat Steps 1 – 5 for each device you wish

to control.

Programming Notes

• Some codes may operate only a few functions of your

device. There may be another code in the Code List

that controls more functions. Test other codes in the

Code List for more functionality.

• If you do not ﬁnd a remote code that works your

device or there are no codes in the Code List for your

device, use the Auto Code Search method in the next

section to program your remote.

• For combination devices such as a TV/DVD combo

or TV/ VCR combo, you may have to enter a code for

each device. (See Controlling Combo Devices, pg. 9.)

• Write down the remote codes used to program the

remote for future reference.

Programming Your Remote

Auto Code Search

The Auto Code Search is a process where you can

search through all the codes stored in the remote to ﬁnd

a code for your device. It is recommended that you read

through all the steps below to familiarize yourself with

the Auto Code Search before starting the process.

1. Manually turn on the device you wish

to control.

Note: The Auto Code Search process cannot be

used for devices without power ON/OFF capability.

Use the Direct Code Entry method in these cases.

2. Press and hold down the SETUP button

on the remote until the red light on the

remote control turns on. Release the

SETUP button. The red light will remain on.

Note: The red light will either be a small light at the

top of the remote or the power ON/OFF button.

3. Press and release the device button on

the remote for the type of device you

wish to control, (for example TV, cbl, dvd,

aux). The red light will blink once and

remain on.

4. With the remote pointed at the device,

press and release the POWER button

on the remote. The remote will send 10

different codes to the device. The red

light will blink once for each code and

remain on after sending the 10 codes.

Did the device turn off?

• If YES, go to Step 5.

• If NO, repeat Step 4 to test the next

10 codes.

5. Manually turn the device back on.

6. With the remote pointed at the device,

press and release the VOL button. The

remote will re-send the ﬁrst code of the

10 codes from Step 4. The red light will

blink once and remain on.

Programming Your Remote

Did the device turn off?

• If YES, you have found a code for the

device. Press and release the same device

button you pressed in Step 3. This will

store the code in the remote. Go to Step 7.

• If NO, continue to press and release the

VOL button until the device turns off to

test the other 9 codes from Step 4.

Be sure to wait approximately 3 seconds

after each VOL button press to allow

the device time to respond to the code.

When the device turns off, you have

found a code for your device. Press and

release the same device button pressed

in Step 3. This will store the code in the

remote. Go to Step 7.

Notes:

• The VOL button can be used to go backwards through

each batch of 10 codes.

• The red indicator light will ﬂash 2 times after testing

the ﬁrst or last code in each batch of 10.

7. Use the remote to turn the device back on.

Test the buttons on the remote to see if the

device responds as you would expect. If the

buttons do not operate the device, return to

Step 2 and repeat this process to search for a

better code to operate the device.

8. Repeat this process for each device you wish

to control.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device.

For example, if you have a TV/DVD Combo, you might

need to set up one code under the TV button to

control the TV part AND a separate code (under any

other Mode button) to control the DVD part.

Using Your Remote

NOTE: Remote will stay in shift mode until the SHIFT button is pressed

again, or until 10 seconds of inactivity. The red indicator light will blink

when the remote is in shift mode.

Using SHIFT Function

The Shift/Setup button allows access to

more than one function for certain buttons.

For Menu, press and release

Shift/Setup then Info/Menu.

For Exit, press and release Shift/

Setup then Previous channel/Exit.

For Guide, press and release Shift/

Setup then Input/Guide.

input

guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Beliebte Universalfernbedienung Handbücher anderer Marken

Pronto

Pronto Peel Bedienungsanleitung

Radio Shack

Radio Shack Wireless Remote Control System Bedienungsanleitung

AUVIO

AUVIO Universal Home Theater Remote Bedienungsanleitung

Philips

Philips Icon SRU4106 Bedienungsanleitung

THOMSON

THOMSON ROC4309 Bedienungsanleitung

Philips

Philips pm625S Bedienungsanleitung

RCA

RCA RCU600WMS - Universal Remote Control Bedienungsanleitung

Blackweb

Blackweb BWB17AV002 Bedienungsanleitung

Marmitek

Marmitek DoorGuard 300 Bedienungsanleitung

Chunghop

Chunghop RM-L618 Bedienungsanleitung

Anderic

Anderic KTN828 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Bedienungsanleitung

Medion

Medion E74023 Bedienungsanleitung

intensity

intensity RM02A Bedienungsanleitung

Sky

Sky MY Bedienungsanleitung

RCA

RCA RCU600M - Universal Remote Control Bedienungsanleitung

Savant

Savant SUR-0500 Kurzanleitung

GDI

GDI GDI-WT2K Bedienungsanleitung