GE 20622 Bedienungsanleitung

Universal Remote

Instruction Manual

Control Remoto Universal

Manual de Instrucciones

20622

Télécommande universelle

Mode d'emploi

Control Remoto Universal

Manual de Instrucciones

Congratulations on your purchase of the GE Universal

Remote Control. The GE Universal Remote Control is

one of the most easy to use remote controls available

today. With the GE Universal Remote Control, juggling

multiple remote controls is a thing of the past!

Your GE Universal Remote Control controls multiple

devices, including the most popular brands of TV, VCR,

DVD, CBL, and SAT. The GE Universal Remote Control

is easy to use, easy to program, and it gives you total

control—at the touch of your ﬁngertips!

IMPORTANT: SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

Introduction ..................................................................................... 2

Setup .................................................................................................. 3

Battery Installation ............................................................... 3

Battery Saver ........................................................................... 3

Code Saver ............................................................................... 3

Button Functions ................................................................... 4

Programming Your Remote ..................................................... 6

Direct Code Entry................................................................... 6

Auto Code Search ................................................................. 8

Using Your Remote ....................................................................10

Controlling Combo Devices ............................................10

Using SHIFT ............................................................................10

Master Volume Feature ....................................................11

Code Identiﬁcation .............................................................12

Reset to Factory Settings .................................................12

Troubleshooting ..........................................................................13

Warranty ........................................................................................14

FCC Statement .............................................................................15

Table of Contents

Your universal remote requires two (2) AAA

Alkaline batteries (not included).

To Install the Batteries

1. On the back of the remote, push down on the tab

and lift the cover off.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AAA Alkaline batteries. Be sure

to use fresh batteries.

3. Press the battery cover back into place.

NOTE: If your remote stops operating properly,

replace the batteries with new ones. The remote will

retain the codes you have programmed for up to 10

minutes after the batteries are removed.

Battery Precautions

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Always remove old, weak or worn-out batteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote. If

buttons are pressed without batteries in the remote,

all codes will be lost.

Setup

RECORD, PLAY, STOP,

REW, FF, PAUSE

TV, CBL/SAT,

DVR/AUX, DVD

Selects device

to control.

Red Indicator Lights when

any button is pressed.

INPUT Selects the video

inputs from available

viewing sources.

Button Functions

INFO Displays/selects

on-screen channel

information.

MENU Press and release

SHIFT/SETUP then MENU/

INFO to display the Menu

on the TV. See “Using

SHIFT for Menu and

Navigation” description

on Page 10 for more

information.

DOT: Used to select digital

channels, e.g., 2.3.

ENTER

For some TV models, used after

direct channel number entry

to immediately change to the

selected channel.

VOLUME UP/DOWN

Changes the volume

level of the product,

normally the TV.

NUMBERS

Enter numbers for direct

channel selection. Some

devices require ENTER

to be pressed after

channel selection.

ON•OFF Turns

devices On or Off.

CHANNEL UP/DOWN

Changes the channels.

Button Functions, cont.

SETUP Used to setup the remote,

and for code search function.

SHIFT Press and release to access buttons

labeled in reverse print (OK, MENU,

EXIT). See “Using SHIFT for Menu and

Navigation” description on Page 10

for more information.

MUTE Turns off the

TV sound while the

picture remains.

OK Selects menu

items for the device

you are controlling.

EXIT Exits On-Screen

Menus and/or

Returns to previous

On-Screen selection.

Programming Your Remote

Your GE universal remote control is designed to

control multiple audio/video devices such as TV,

DVD, DVR, satellite, cable and audio using only one

remote. To use this remote, you will need to program

it to control the devices of your choice. There are two

ways to program the remote - direct code entry or

auto code search.

Direct Code Entry (Recommended)

1. Locate the Remote Code List provided

in this manual. Find the DEVICE

CATEGORY you wish to program (for

example TV, DVD, CBL/SAT, DVR/

AUX) and then ﬁnd the BRAND of that

device. Circle all the codes under that

brand. Example: For a GE TV, locate the

TV code section then circle all of the

GE TV codes.

2. Manually turn on the device you wish

to control.

3. Press and hold the SETUP button

until the red indicator light stays on

(approximately 4 seconds) and then

release the SETUP button.

4. Press and release the desired device

button on the remote (TV, DVD, CBL/

SAT, DVR/AUX). The red indicator will

blink once and then remain on.

5. Enter the ﬁrst 4-digit code previously

found in the code list using the

number buttons on the remote. If the

code entered is a valid code, the red

indicator light will turn off. If the code

entered is not a valid code, the red

indicator light will ﬂash and remain on

allowing you to re-enter the code.

Note: If no buttons are pressed for 10

seconds, the remote will exit the SETUP

mode and you will have to start over.

Programming Your Remote, cont.

6. Point the remote at the device. Press

the POWER button—if the device

turns off, no further programming is

required for that device. If the device

does not turn off, return to step 3

and use the next code found in the

code list. Continue this process until

a code for your device is found.

7. Repeat this process for each device

(for example TV, DVD, CBL/SAT, DVR/

AUX) in your home entertainment

system you wish to control. Four

devices can be programmed.

Programming Notes

• If your device does not respond to the remote

after trying all codes listed or your brand is not

listed in the code list, use the Auto Code Search

method to program your remote.

• Sometimes the ﬁrst code that “works” with your

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Try other codes

from the code list for more functionality.

• With the Direct Code Entry method, you can

program any device button to control any device

in your home entertainment system.

For example, you can use the DVR/AUX device

button to control an audio receiver or a DVD, VCR,

satellite device, etc.

• For combination devices, you may have to enter a

code for each device. For example, for a VCR/DVD

device, you may have to enter a code for the DVD

under the DVD button and enter a code for the

VCR using a different device button on the remote.

• Write down the code found to operate your device

for future reference.

Programming Your Remote, cont.

Auto Code Search

The Auto Code Search searches automatically

through all of the codes stored in this remote. Read

all the following steps prior to starting the auto

search as you will need to be prepared to lock-in the

proper code when found.

1. Manually turn on the device you wish

to control.

2. Press and hold the SETUP button until

the red indicator light stays on

(approximately 4 seconds) and then

release the button.

3. Press and release the desired device

button on the remote (TV, DVD, CBL/

SAT, DVR/AUX). The red indicator will

blink once and then remain on.

4. Point the remote at the device and

press and release the POWER button

(for TV) or PLAY button (for DVD, VCR,

etc.) to start the search. The red

indicator will ﬂash (approximately

every 2 seconds) as the remote

searches. Note: The remote must be

pointed at the device for the duration

of this search.

5. Place your ﬁnger on the #1 button so

you are prepared to lock-in the code.

6. When the device shuts off or begins

playing, press the #1 button to

lock-in the code. The red indicator

light will turn off. Note: You have

approximately two seconds after the

device shuts off or begins playing to

lock-in the code.

7. Point the remote at the device and

check to see if the remote operates the

device as desired. If it does, no further

programming is required for that

device. If it does not, return to step 2

and start the auto search again.

Programming Your Remote, cont.

8. Repeat this process for each device (for example

TV, DVD, SAT, AUX) in your home entertainment

system you wish to control. Four devices can

be programmed.

Programming Notes

• This process may take several minutes as the

remote contains many codes.

• When using the Auto Code Search programming

method, the device button corresponding to

the type of device you want to control must be

selected (for example, the TV device button must

be selected in step 3 if you want to control a TV,

the DVD device button for a DVD player, etc.)

• The SETUP button can be used during the search

process to reverse the direction of the search of

the remote codes. For example, if you miss the

code for your device and the remote is continuing

to search (as indicated by the blinking red light),

press the SETUP button and the code search will

reverse direction and return to the code.

• Sometimes the ﬁrst code that “works” with your

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Continue the

auto code search as directed above until the best

code is found.

Using Your Remote

For MENU, press and release

SHIFT/SETUP then INFO/MENU.

For OK, press and release

SHIFT/SETUP then MUTE/OK.

For EXIT, press and release

SHIFT/SETUP then LAST/EXIT.

For Up, Down, Left or Right Navigation,

press and release SHIFT/SETUP

followed by the respective Channel or

Volume button.

SPECIAL NOTE: Remote will stay in shift mode

until the SHIFT button is pressed again, or until 10

seconds of inactivity.

Using SHIFT for Menu and Navigation

The SHIFT button allows access to more than one

function for certain buttons.

Use the SHIFT/SETUP button prior to accessing

the MENU, OK, EXIT and Navigation functions,

for example:

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device.

For example, if you have a TV/DVD Combo, you might

need to set up one code under the TV button to

control the TV part AND a separate code (under any

other Mode button) to control the DVD part.

Andere Handbücher für 20622

Inhaltsverzeichnis

Sprachen:

Beliebte Universalfernbedienung Handbücher anderer Marken

Pronto

Pronto Peel Bedienungsanleitung

Radio Shack

Radio Shack Wireless Remote Control System Bedienungsanleitung

AUVIO

AUVIO Universal Home Theater Remote Bedienungsanleitung

Philips

Philips Icon SRU4106 Bedienungsanleitung

THOMSON

THOMSON ROC4309 Bedienungsanleitung

Philips

Philips pm625S Bedienungsanleitung

RCA

RCA RCU600WMS - Universal Remote Control Bedienungsanleitung

Blackweb

Blackweb BWB17AV002 Bedienungsanleitung

Marmitek

Marmitek DoorGuard 300 Bedienungsanleitung

Chunghop

Chunghop RM-L618 Bedienungsanleitung

Anderic

Anderic KTN828 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Bedienungsanleitung

Medion

Medion E74023 Bedienungsanleitung

intensity

intensity RM02A Bedienungsanleitung

Sky

Sky MY Bedienungsanleitung

RCA

RCA RCU600M - Universal Remote Control Bedienungsanleitung

Savant

Savant SUR-0500 Kurzanleitung

GDI

GDI GDI-WT2K Bedienungsanleitung