Geemarc CL7300v2 Bedienungsanleitung

CL7300v2

Digital TV Listene

English

Introduction

The Geemarc Digital TV Listener is an amplification system specifically designed

for people with hearing difficulties.

It can be used with all kinds of Audio, Television systems, suitable for individuals

or groups without any interference.

Audio output from a TV or audio device is encoded and transmitted by the Base,

the wireless Headset receives the signal and decodes it to original audio sound.

One Base can be paired with up to 4 Headsets.

Safety & Care advice

To make the best use of this product and to use it safely, please read these

instructions thoroughly before use and keep safe for future reference.

Warning: This product can be very loud. Take care to prevent others from

using this product, if they do not have the same level of hearing loss. Excessive

sound pressure from earphones and headphones can cause hearing loss.

Caution: Electric shock. DO NOT insert unattached plug heads in to mains

power sockets. Plug heads MUST be fitted to the power adaptor.

Electrical connection: The unit is designed to operate from a 100-240VAC -

50/60Hz supply. (Classified as 'hazardous voltage' according to EN 60950

standard).

The unit does not incorporate an integral power on/off switch. To disconnect the

power, either switch off supply at the mains power socket or unplug the AC

adaptor. When installing the unit, ensure that the mains power socket is readily

accessible.

Caution: Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Keep the unit away from heat sources.

DO NOT expose the unit to direct sunlight.

Clean the Headset and ear pads regularly.

DO NOT modify the unit in any way.

Please note: The unit may be subject to interference from appliances that

generate strong electrical or magnetic fields e.g. microwaves, mobile phones,

lighting transformers etc.

Table of Contents

Pack contents 2 Pairing extra headsets 11 -12

First use / Charging batteries 3 - 5 Cleaning & Maintenance 12

Connecting to TV, HiFi and other

audio equipment 6 - 8

Spare/replacement parts 13

Using Headset 8-10 Customer support 13

Headset adjustments 8-10 General information 13-14

Battery status & recharging 10-11

1. Headset 2. Alternative ear pads

3. Base 4. Power adaptor with cable

(1.5m) (UK, EU & US)

5. Slider tool 6. Batteries

7. 3.5mm to 3.5mm cable

(1.5m)

8. 3.5mm to 6.3mm adaptor

9. 3.5mm to 2 pin RCA cable

(25cm)

10. 2-pin RCA scart adaptor

11. Microphone

Pack Contents

First use / Charging batteries

Important: The Geemarc Digital TV Listener is supplied with two batteries.

Before use, batteries MUST be fully charged, full charge will take about 2-3 hours

when the battery is empty.

Caution: If battery is already fully charged, the red LED will stay off.

Once fully charged the TV Listener has an approximate operating time of up to 3

hours (per battery, with Headset on medium volume).

Batteries cannot be overcharged, but to save power the Base should be

disconnected from the power supply when not in use.

Battery Warnings:

•DO NOT attempt to dismantle.

•DO NOT dispose of in fire.

•DO NOT swallow.

•Keep away from children.

•Batteries are to be inserted with the correct polarity.

•DO NOT short-circuit the supply terminals.

•Exhausted batteries are to be removed from the product.

•Only use Geemarc supplied 'Li-Po' batteries.

•Caution: Risk of explosion if battery is replaced incorrectly or

fitted with the wrong type of battery. Dispose of used batteries

according to the instructions.

Insert power adaptor into mains power

socket. Insert power jack (7) into ‘DC

IN 5V’ socket on the back of the Base.

Insert batteries (6) into Headset and

Base.

Place Headset in Base.

Caution: Please be sure to insert the

battery correctly (see above).

Turn power on at mains and Base.

Red lights will show on Base and

Headset to indicate batteries are

charging.

After 2-3 hours, when fully charged the

red lights will be off.

Connecting to TV, HiFi and other audio equipment

There are a number of alternative methods of connecting to the unit depending on

the make of TV, HiFi equipment.

Important: The Base MUST connect to 'OUTPUT' sockets on the TV, HiFi

equipment (never use the INPUT access sockets).

Important: If you are using cable TV, satellite, Internet or other services in

conjunction with your TV or sound device please ensure that you connect the

CL7300 to an audio output access on your TV and NOT on your set top box. If

you are unsure or cannot identify the right connection or the input/output definition

please refer to the user manual of your TV. A connection of the CL7300 to your

set top box instead of your TV output could result some channels being seen

without sound.

Please note: In the event of having difficulty with the connections, please call the

Customer Helpline: 01707 384438

Using 3.5mm to 3.5mm cable: Insert

one 3.5mm jack (8) into ‘Audio’ socket

on Base, insert other 3.5mm jack into

the ‘headphone’ socket on the TV, HiFi

equipment. If required use 3.5mm to

6.3mm jack adaptor (9).

Using 3.5mm to RCA cable: Insert

3.5mm jack (8) into 3.5mm RCA cable

(10). Connect to the RCA jacks (10) to

the corresponding red and white

'OUTPUT' sockets on the TV, HiFi

equipment.

Using scart adaptor: Insert 3.5mm

jack (8) into 3.5mm to RCA cable (10).

Insert scart adaptor (11) into a

compatible scart socket on the TV, HiFi

equipment.

Connect to corresponding red and

white RCA jacks (10) to scart adaptor

(do not use the yellow socket).

Note:

Some televisions and audio

devices have an audio output SCART

level greater than the 300mV standard.

This can cause some distortion or a

very high acoustic level, even with the

Volume set to Low. If this happens,

please contact the Geemarc Customer

Services department. They will be able

to provide you with a solution to

attenuate the sensitivity of your

CL7300.

Microphone connection: Only use the

supplied Geemarc microphone. Plug

microphone jack (12) into ‘MIC’ socket

on Base and place microphone near

source you wish to listen to.

Note: Volume levels will be lower and

background noise may be picked up

when using the microphone.

Using Headset: Once charged and

connected to your TV, HiFi equipment,

open the arms and Headset will

operate. A green light on the Headset

will show it is in use.

Headset will switch off when arms are

fully released.

Volume adjustment:

Press ‘+’ button to increase volume and

‘-’ button to decrease volume.

Headset beeps when volume reaches

maximum or minimum.

Headset adjustments

Volume, Balance, Tone and Mono/Stereo settings are preset to their middle

settings, these will be suitable for the majority of users.

Ensure that you try the Headset before adjusting the preset settings.

If adjustments are required use the 'slider tool' to adjust the settings.

Important: Once all the adjustments are complete, ensure that the Headset

slider is set to the Volume adjustment as described in step 11.

Use the slider tool (5) to adjust the

Volume, Balance, Tone or switch

Mono to Stereo. Open the back panel

on the Headset. 3 ‘slider switches’ will

be present.

Volume adjustment:

Set ‘BAL VOL’ slider to ‘VOL’.

Set ‘T <-> B/V’ slider to ‘B/V’

Press ‘+’ button to increase volume and

‘-‘ button to decrease volume.

Headset beeps when volume reaches

maximum or minimum.

Balance adjustment:

Set ‘BAL VOL’ slider to ‘BAL’

Set ‘T <-> B/V’ slider to ‘B/V’

Press ‘-’ button to decrease sound on

RIGHT side. Press ‘+’ button to

decrease sound on LEFT side.

Headset beeps when balance reaches

maximum, middle or minimum.

Inhaltsverzeichnis

Andere Geemarc Verstärker Handbücher

Geemarc

Geemarc CL11 Bedienungsanleitung

Geemarc

Geemarc clearsound amplicall 20 Bedienungsanleitung

Geemarc

Geemarc loophear 160 v2 Bedienungsanleitung

Geemarc

Geemarc In-Line Amplifier CLA30/40 Bedienungsanleitung

Geemarc

Geemarc P-Amp40 Bedienungsanleitung

Geemarc

Geemarc ClearSound CL7150 Bedienungsanleitung

Geemarc

Geemarc CLA-40 VOX Bedienungsanleitung

Geemarc

Geemarc LoopHEAR 160 Bedienungsanleitung

Geemarc

Geemarc AMPLICALL10 Bedienungsanleitung

Geemarc

Geemarc LoopHEARTM 20 Bedienungsanleitung

Geemarc

Geemarc Loop Hear LH600 Bedienungsanleitung

Geemarc

Geemarc CLA-30 Bedienungsanleitung

Geemarc

Geemarc LoopHEAR 102 V2 Bedienungsanleitung

Geemarc

Geemarc AMPLICALL10 Bedienungsanleitung

Geemarc

Geemarc LOOPHEAR 10 Bedienungsanleitung

Geemarc

Geemarc CLA-40 VOX Bedienungsanleitung

Geemarc

Geemarc CL7160 Bedienungsanleitung

Geemarc

Geemarc AMPLICALL 10 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung