Gefen COMPAUD-CAT5-148 Bedienungsanleitung

1:8 Component/

Audio Over CAT5

Distribution Ampliﬁer

Model EXT-COMPAUD-CAT5-148

USER MANUAL

www.gefen.com

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9120

Technical Support Hours:

8:00 AM to 5:00 PM Monday through Friday PST

Write To:

Gefen Inc.

C/O Customer Service

20600 Nordhoff St.

Chatsworth, CA 91311

[email protected]

www.gefen.com

Notice

Gefen Inc. reserves the right to make changes in the hardware, packaging and any

accompanying documentation without prior written notice.

1X8 Component/Audio Over CAT5 Distribution Ampliﬁer is a trademark of Gefen Inc.

ASKING FOR ASSISTANCE

TABLE OF CONTENTS

Introduction / Operation Notes

Features

Panel Description - Sender

Panel Description - Receiver

Connecting the 1x8 Component/Audio Over CAT5 DA

Operating the 1x8 Component/Audio Over CAT5 DA

Wiring Diagram

Network Wiring Diagram

Speciﬁcations

Warranty

Use only industry standard Category-5 Enhanced (CAT5e) cable to operate the 1:8

Component/Audio Over CAT5 DA

Receiver units are sold individually

Unit will convert digital audio to analog audio and analog audio to digital audio. It will

nothoweverdown-mixmultichannel digitalaudio tracksto analog2 channel.Please

see page 5 for additional information

Both the sending and receiving units must be powered with the supplied power

adapters to operate

Fieldtermination of CAT5ecablingmust adhere tothe TIA/EIA-568-Bspeciﬁcation.

Please see page 8 for additional information

•

The 1:8 Component/Audio Over CAT5 Distribution Ampliﬁer (DA) sends up to 8

identical sets of sparkling clear component video with audio to remote locations via

eight CAT5 cables at distances of up to 1000 feet. Now you can reliably and cleanly

distribute up to eight copies of a video signal with digital or analog audio to remote

locations without having to worry about signal drop-off and loss of quality.

How It Works

Simply plug in your component video and audio from your source to the 1:8

Component/Audio DA Sender. Your audio can be analog, digital SPDIF or digital

TOSlink. Run your CAT5 cables from the Sender box to up to 8 remote destinations,

then connect a receiver box to each CAT5 cable at the terminating end. Attach the

displays to the receivers to, power on all equipment, and you should see beautiful

video. All audio ports on the receiver will also be active, so even if your source only

had analog audio your Component Audio Receiver will have digital and analog

audio output. The sender and receiver both will be powered individually by 5V power

supplies.

INTRODUCTION

READ THESE NOTES BEFORE INSTALLING OR OPERATING

THE 1:8 COMPONENT/AUDIO OVER CAT5 DA

OPERATION NOTES

FEATURES

Features

Supports up to 1080p component video

Supports analog L+R audio and multichannel digital optical or coaxial

No Loss of Quality

Plug and play installation

Equalization adjustment for different CAT5e skews

One CAT5e cable for extension

Package Contents - 1:8 Component/Audio Over CAT5 DA Sender

(1) 1:8 Component/Audio Over CAT5 Distribution Ampliﬁer

(1) 6 Ft. 3 RCA Component Cable (M-M)

(1) 6 Ft. RCA Cable (M-M)

(1) 5V DC 2 AMP Power Supply

(1) User manual

Component/Audio Receiver - Sold Separately

•

PANEL DESCRIPTIONS - SENDER

Front Panel

Back Panel

Power LED

Indicator

Analog Audio

Input Component

Input

SPDIF

In RJ-45 Output

Port 1 RJ-45 Output

Port 3 RJ-45 Output

Port 5 RJ-45 Output

Port 7 5V DC Power

Input

Optical In RJ-45 Output

Port 2 RJ-45 Output

Port 4 RJ-45 Output

Port 6 RJ-45 Output

Port 8

PANEL DESCRIPTION - RECEIVER

Front Panel

Back Panel

Analog Audio

Output

Component

Output

SPDIF

Out

RJ-45 Input

Port

Power LED

Indicator

Focus

Trim Pot

Optical Out

Brightness

Trim Pot

5V DC

Power Input

CONNECTING THE 1:8 COMPONENT/AUDIO OVER CAT5 DA

Connect the component source into the 1:8 Component/Audio Over CAT5 DA

using the provided 3 RCA component cable.

Connect the audio source to the 1:8 Component/Audio Over CAT5 DA using

one of the 3 options below:

Digital Optical - user supplied optical cable

Digital Coaxial - supplied SPDIF cable

Analog audio - user supplied analog RCA cables

Connect one CAT5e cable for each component/audio extension (up to 8) from

the 1:8 Component/Audio Over CAT5 DA to a Component/Audio Receiver.

Connect a display to each of the Component/Audio Receivers using a user

supplied 3 RCA component cable.

Connect the audio output of the Component/Audio Receiver to an audio input

device using one of the options below:

Digital Optical - user supplied optical cable

Digital Coaxial - user supplied SPDIF cable

Analog audio - user supplied analog RCA cables

See note below for additional info on audio connectivity.

Connect the supplied 5V DC power adapters to the 1:8 Component/Audio Over

CAT5 DA sender, and one 5V DC power adapter to each Component/Audio

Receiver (up to eight).

Power on all monitors ﬁrst, and then power on the source.

Note: The 1:8 Component/Audio Over CAT5 DA has the ability to convert

analog audio signals to digital, and digital audio signals to analog. It will cross-

convert any 2 channel audio signal (analog or digital) or pass multi-channel

audio directly from the digital inputs to the digital outputs. However, it cannot

down-mix digital multichannel audio, such as Dolby Digital and DTS, to the 2

channel analog outputs. Do not attempt to connect the 2 channel analog audio

outputs when passing digital multi-channel content. The resulting output will

be unrecognizable. Additionally, the 1:8 Component/Audio Over CAT5 DA can

cross-convert between digital SPDIF and digital Optical. For example, you can

input a digital SPDIF cable on the sender and connect an digital optical cable

on the output.

OPERATING THE 1:8 COMPONENT/AUDIO OVER CAT5 DA

Once all cables are connected and all devices are powered on, there is no further

operations needed to utilize the 1:8 Component/Audio Over CAT5 DA. However, it

may be necessary to tune the signal depending on the quality of CAT5e cabling and

distance that the signal has to travel.

Brightness

If the image appears too dim or too bright, adjust the brightness trim pot on the front

of the Component/Audio Receiver.

Insert a small ﬂathead device into the brightness trim pot hole and turn the trim pot

in either a clockwise or counterclockwise direction. Turn the trim pot in very small

increments until the desired brightness is reached.

Focus

If the image is out of focus, or the colors are smeared, adjust the focus trim pot on

the front of the Component/Audio Receiver.

Insert a small ﬂathead device into the focus trim pot hole and turn the trim pot in

either a clockwise or counterclockwise direction. Turn the trim pot in very small

increments until the image clears and there is not blurriness or smearing.

WIRING DIAGRAM

Component Video

Analog Audio

Digital Audio

CAT5e

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gefen Verstärker Handbücher

Gefen

Gefen 1x8 HDTV DA Bedienungsanleitung

Gefen

Gefen HDMI-144 Bedienungsanleitung

Gefen

Gefen EXT-HDMI-CAT5-148 Bedienungsanleitung

Gefen

Gefen Super Booster Plus Bedienungsanleitung

Gefen

Gefen EXT-COMPAUD-143 Bedienungsanleitung

Gefen

Gefen HDMI1.3-1410 Bedienungsanleitung

Gefen

Gefen EXT-VGA-CAT5-148S Bedienungsanleitung

Gefen

Gefen EXT-COMPAUD-148 Bedienungsanleitung

Gefen

Gefen DVI DL Splitter Bedienungsanleitung

Gefen

Gefen DVI-248 Bedienungsanleitung

Gefen

Gefen EXT-HDMI1.3-1410-BLK Bedienungsanleitung

Gefen

Gefen 2x8 DVI DA Bedienungsanleitung

Gefen

Gefen EXT-COMPAUD-143 Bedienungsanleitung

Gefen

Gefen EXT-DVI-142DLN Bedienungsanleitung

Gefen

Gefen ADC-144 Bedienungsanleitung

Gefen

Gefen ex tend it VDX 600 Bedienungsanleitung

Gefen

Gefen EXT-DVI-144N Bedienungsanleitung

Gefen

Gefen EXT-HDMI-144 Bedienungsanleitung

Gefen

Gefen 1x8 DVI DA Bedienungsanleitung

Gefen

Gefen HDMI-142 Bedienungsanleitung

Gefen

Gefen 1:4 HDMI CAT5 Bedienungsanleitung

Gefen

Gefen EXT-DVI-141DLBP Bedienungsanleitung

Gefen

Gefen CAT-5 DA Bedienungsanleitung

Gefen

Gefen AUD-144 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung