GEIGER GF0040 Bedienungsanleitung
EN
GEIGER RADIO SYSTEMS
Sunshade controls
Radio remote controls
for rolling shutters and
sunshade controls
3-channel GF0040
6-channel GF0041
12-channel GF0042
Comfort handheld transmitter
with graphic display
Operating instructions
LIVINGROOM
AWNING 1
AWNING 2
BLIND 1
BLIND 2
BLIND 3
LIGHT 1
EDIT
EN
2Gerhard Geiger GmbH & Co. | 100W0624 0311en
EN
Contents
1. Introduction .........................................................................................................................................3
2. Safety instructions ...............................................................................................................................3
3. Intended use ........................................................................................................................................3
4. Transmitter types ................................................................................................................................3
4.1 Comfort 3-channel display handheld transmitter GF0040 ...........................................................3
4.2 Comfort 6-channel display handheld transmitter GF0041 ...........................................................3
4.3 Comfort 12-channel display handheld transmitter GF0042 .........................................................4
5. Operating conditions ..........................................................................................................................4
5.1 Operational mode ........................................................................................................................4
5.2 Sleep mode ..................................................................................................................................4
6. Operating instructions.........................................................................................................................5
6.1 Multifunction keys.........................................................................................................................5
6.2 Navigation keys............................................................................................................................5
6.3 Turning on the display transmitters GF0040 / 41 / 42............................................................................6
6.4 Selection of the actuator / receiver ..............................................................................................6
6.5 Send a radio command ................................................................................................................6
7. Programming and coding instructions .............................................................................................7
7.1 Select the language ....................................................................................................................7
7.2 Enter areas, devices, actuators and codings ..............................................................................7
7.3 Transfer set codings on actuators / receivers ...........................................................................12
7.4 Selection of various actuators / receivers .................................................................................12
7.5 Delete or modify areas, actuators and codings..........................................................................13
7.4.1 Delete individual actuators ..............................................................................................13
7.4.2 Reset to factory setting ...................................................................................................14
8. Care and Maintenance ......................................................................................................................15
9. Notes on waste disposal ...................................................................................................................15
10.Technical data ....................................................................................................................................15
11.Declaration of conformity..................................................................................................................15
3
www.geiger-antriebstechnik.de
EN
1. Introduction
The purchase of a comfort handheld transmitter with graphic display was a good decision.
You have acquired a high-quality product from the house of GEIGER.
The comfort handheld transmitters allow you to send three, six or twelve different codings to
control a range of different actuators (receivers). The control can be either
• Individual
• Grouped or
• Centralized .
No labour-intensive and time-consuming laying of control lines is needed as all switching signals
are transmitted via radio.
The following actuators (radio receiver with integrated control) can be controlled with the GEIGER
comfort handheld transmitters:
• all GEIGER motors with built-in radio receivers
• all external GEIGER radio receivers
2. Safety instructions
The operation of the actuators and the electrical products shall only take place when you are sure
that there is no risk to people, animals or property.
• The radio remote control should be kept out of reach of children
• If service work or adaptations are necessary, the device is to be immediately taken out of
service and secured against inadvertent use.
3. Intended use
The comfort handheld transmitter is only to be used for its intended purpose as described under
Section 1 of the operating instructions.
Changesormodicationstothetransmittervoidanyrightstoclaimsundertheguarantee.After
unpacking the device, check it right away for any damage. Transport damage is to be reported to
the supplier immediately.
4. Transmitter types
4.1 Comfort 3-channel display handheld transmitter GF0040
• One area for the selection of three different codings (actuators).
• Labelling of the actuators with library terms
• Anynumberofreceiverscanbeassignedtothethreedifferentcodings
• Large keys for easy navigation and intuitive operation
• Multifunction keys to perform the functions shown on the transmitter display, for example
sun automatic on / off.
4.2 Comfort 6-channel display handheld transmitter GF0041
• One area for the selection of six different codings (actuators).
• Labelling of the actuators with library terms
• Anynumberofreceiverscanbeassignedtothethreedifferentcodings
• Large keys for easy navigation and intuitive operation
• Multifunction keys to perform the functions shown on the transmitter display, for example
sun automatic on / off.
4Gerhard Geiger GmbH & Co. | 100W0624 0311en
EN
4.3 Comfort 12-channel display handheld transmitter GF0042
• Two areas for the selection of six different codings (actuators).
• Labelling of the actuators with library terms
• Anynumberofreceiverscanbeassignedtothethreedifferentcodings
• Large keys for easy navigation and intuitive operation
• Multifunction keys to perform the functions shown on the transmitter display, for example
sun automatic on / off.
5. Operating conditions
In order to maximize battery lifetime, three different energy modes are available.
The power-saving mode is also equipped with a key lock, for avoidance of unintentional switching,
such as the closing of a shutter.
5.1 Operational mode
PressOKkeytoturnonthetransmitter(wakeupprocessfromthepowersavingmode)therst
locationshowsonthedisplay.Allkeysareactiveandthedisplayisilluminated.
5.2 Sleep mode
If no action takes place within 10 seconds, the transmitter goes into sleep mode. The display light
shuts off but all keys keep active. When actuating a key again the display light turns on.
You get the transmitter to enter the deep sleep mode when all keys are not actuated for 1 minute.
The display shuts down. The OK key keeps active.
To wake the transmitter back up, simply press the OK key.
5
www.geiger-antriebstechnik.de
EN
6. Operating instructions
6.1 Multifunction keys
The functions of the keys appear on the display above each key:
„ML“ multifunction key on the left side
Exit selected menu item
„MO“ multifunction key top
Change to menu level “settings”
„MR“ multifunction key on the right side
Attention:thiskeyconrmsinmenuitem“factory
setting” the return to “factory setting”
„ED“ multifunction key EDIT
opens the programming mode press key
4 seconds
„OK“ multifunction key OK
toconrmsettings
6.2 Navigation keys
These keys have several functions:
Exit or change the menu items
Vertical change of the menu items or send the selected
radio command
“OK” navigation key
toACTIVATEthedevice
to SEND (one-channel) and
to CONFIRM several functions.
EDIT
OK
LIVINGROOM
AWNING 1
AWNING 2
BLIND 1
BLIND 2
BLIND 3
LIGHT 1
EDIT
6Gerhard Geiger GmbH & Co. | 100W0624 0311en
EN
6.3 Turning on the display transmitters GF0040 / 41 / 42
Press “OK” key
The device turns out when no keys are activated.
After 10 seconds the display light turns off, after
60 seconds, the device enters the deep sleep mode.
6.4 Selection of the actuator / receiver
To select «Blind 2» activate navigation key 3 times:
6.5 Send a radio command
Press “OK” key:
With the navigation keys, select the required direction and
press key to send command. The blind can be stopped with
the opposite key.
With the multifunction key in the middle, return to actuator
selection area 1 living room
LIVINGROOM
AWNING 1
AWNING 2
BLIND 1
BLIND 2
BLIND 3
LIGHT 1
EDIT
LIVINGROOM
AWNING 1
AWNING 2
BLIND 1
BLIND 2
BLIND 3
LIGHT 1
EDIT
BLIND 2
LIVINGROOM
AWNING 1
AWNING 2
BLIND 1
BLIND 2
BLIND 3
LIGHT 1
EDIT
7
www.geiger-antriebstechnik.de
EN
7. Programming and coding instructions
7.1 Select the language
Press OK key to activate the comfort handheld transmitter
The GEIGER logo shows for 3 seconds
Press key „EDIT“ for > 4 seconds till an arrow displays
on the left side
EDIT > 4 sec.
Press the multifunction key when the arrow appears
Display goes to „setting“.
Press 1x navigation key „DOWN“ to select the menu item
„Language“ and press the „OK“ key to get to the language
selection. Select the desired language, press again the OK
keytoconrmtheselection.
To return to the starting point, press 2 x the multifunction
key „ML“
7.2 Enter areas, devices, actuators and codings
The comfort handheld transmitters are free encoded.
You can assign yourself the corresponding actuators
(awnings, Venetian blinds, yard gates, garage doors, etc.)
as well as different codings.
Activate the key symbols listed in the middle to get to the
display indications.
Note:Actuator=device/receiver
1 Press OK key to activate the comfort handheld transmitter.
The GEIGER logo appears for 3 seconds.
2 YouarenowinAREA1.
The 3-channel and 6- channel transmitters have
only one area.
12-channel transmitter: you can switch between area 1
and 2 using the horizontal navigation keys.
SETTINGS
AREANAME
LANGUAGE
RESET
OK
LANGUAGE
DEUTSCH
ENGLISH
FRANCAIS
NEDERLANDS
POLSKI
OK
AREA 1
MARKISE 1
EDIT
8Gerhard Geiger GmbH & Co. | 100W0624 0311en
EN
3 Press key „EDIT“ for > 4 seconds till an arrow shows
on the left side
EDIT > 4 Sek.
Press the multifunction key when the arrow appears
Display changes to „SETTING“.
4 An„AREANAME“cannowbeselectedfromthelibrary
Press „OK“ key
12-channel transmitter: you can now select area 1 or 2 using
the vertical navigation keys UP/DOWN
Now press again the „OK“ key
Youarenowonthenextdisplayforthe„AREANAME“,the
so-called library.
5 ActivatetheverticalnavigationkeysUP/DOWNtoselectthe
name for your area. You can use the horizontal navigation keys
toscrollpagebypageandselectthenameswithUP/DOWN.
UP/DOWNpagebypage
6 Example: in order to select the area name „LIVING ROOM“
proceed as follows:
To take over the new area name „LIVING ROOM“ press x 2 the
multifunction key „ML“
AREA 1
MARKISE 1
EDIT
SETTINGS
AREANAME
LANGUAGE
RESET
OK
AREANAME
BATHROOM
OFFICE
ROOFSHADE
ROOF WIND. 1
ROOF WIND. 2
ROOF WIND. 3
OK
AREANAME
LIVINGROOM
EDIT
LIVINGROOM
EDIT
9
www.geiger-antriebstechnik.de
EN
7 In order to set up an actuator (receiver):
Press the „EDIT“ key
EDIT
Displaychangesto„SETTINGS“/„NAME“
8 Intheopeneld„NAME“youcannowsetadevice(receiver)
Press „OK“ key
OK
Select the device name from the library.
9 If you wish to start with Venetian blind 1 in the living room:
Pressvetimestherighthorizontalnavigationkey
Andthentwicetheverticalnavigationkeydownwards
10 Press the „OK“ key to select the name BLIND 1
11 Now enter coding and actuator type.
Note:Actuator=device/receiver
Press once the navigation key „DOWN“ and then „OK“.
The display now shows three code switches.
Depending on the actuator type one, two or three codings are
required. For actuators that are operated with two channels,
the second coding is automatically generated.
SETTINGS
NAME
CODE
DELETE
EDIT
DEVICENAME
BATHROOM
OFFICE
ROOFSHADE
ROOF WIND. 1
ROOF WIND. 2
ROOF WIND. 3
OK
DEVICENAME
KORRIDOR
KITCHEN
BLIND 1
BLIND 2
BLIND 3
BLIND 4
OK
BLIND 1
NAME
CODE
DELETE
OK
CODES
OK
+
0
-
+
0
-
+
0
-
If handheld transmitters GJ..01
- ..06 are already programmed
on actuators / receivers, the
DIP switches
8 +9 should be set as follows:
Keypair1 UP:00DOWN:0–
Key pair 2
UP
:–0
DOWN
:––
Key pair 3
UP
: 0 +
DOWN
: + 0
10 Gerhard Geiger GmbH & Co. | 100W0624 0311en
EN
12 Activatethehorizontalnavigationkeyrighttoenterthecoding
switchofDIPswitch1.Activateverticalnavigationkeytochange
DIP switch from position „-“ to „0“ or „+“.
The DIP switches 8 and 9 should only be changed in case of a
specicchannelapplication.
Leavetherstcodingswitchtoselecttheactuatortype
…
...untilyouchangeovertotheashingtopbox.
13 Activatenavigationkeytogettothesecondcodingswitch.
The actuator can be selected with the next operation.
14 Press„OK“keytoenter„ACTUATORSSELECTION”
Select the Venetian blind symbol with the navigation key DOWN
Press the „OK“ key to save the actuator selection
The display changes to show „coding switch 2“ back.
The DIP switch settings 1-7 are saved, the DIP switches 8 and 9
are set on the next channel.
If the selected actuator „Venetian blind 1“ is not controlled
by a sensor, then continue straight to step 17.
CODES
OK
+
0
-
+
0
-
+
0
-
CODES
OK
+
0
-
+
0
-
+
0
-
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere GEIGER Empfänger Handbücher
