Generac Power Systems 7000exl Bedienungsanleitung

Owner’s Manual / Manuel de l'Utilisateur

Questions? Help is just a moment away!

Vous avez des questions? Vous n'avez pas besoin d'aller loin pour trouver de l'aide!

Call: Generac Generator Helpline / Appelez la ligne d'assistance de Generac Motor - 1-800-270-1408 M-F 8-5 CT

Web: www.generac-portables.com or www.briggsandstratton.com

Model No. 1657-1 (7,000 Watt AC Generator) Manual No. 191520GS Revision 1 (11/20/2002)

Safety Rules / Règles de Sécurité . . . . . . . . . . . . . . . . . . . 2-3 / 20-21

Know Your Generator / Connaissez Votre Générateur . . . . . . 4 / 22

Assembly / Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 / 23

Operation / Opération . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 / 24-28

Product Specifications / Caractéristiques du Produit . . . . . . . 11 / 29

Maintenance / Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 / 29

Storage / Rangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 / 30

Troubleshooting / Dépannage . . . . . . . . . . . . . . . . . . . . . . . . 13 / 32

Schematic / Schéma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Wiring Diagram / Circuit de Câblage . . . . . . . . . . . . . . . . . . . . . . 15

Replacement Parts / Pièces de Rechange . . . . . . . . . . . . . . . . . 16-19

Notes / Remarques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 33-34

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Last Page

• Generator / Générateur

• Wheel kit / Ensemble de roulettes

• Storage cover / Couverture d'emmagasinage

• Battery / Batterie

• Battery charge cables / Câbles de charge de batterie

• Battery float charger / Chargeur de flotteur de batterie

• Locking 30 Amp plug / Prise de verrouillage 30 Ampères

• Two bottles of engine oil / Deux bouteilles d'huile moteur

• Three packets of fuel stabilizer / Trois paquets de stabilisateur

d'essence

• Owner's manual / Manuel de l'utilisateur

• Engine manual / Manuel du moteur

*If any parts are missing or damaged, call 1-800-270-1408.

*Si certaines pièces sont manquantes ou endommagées, appelez le

1-800-270-1408.

Parts Included* / Pièces Incluses* Table of Contents / Table des Matières

7000EXL Extended Life Generator

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

This generator is an engine–driven, revolving field, alternating

current (AC) generator. It was designed to supply electrical

power for operating compatible electrical lighting, appliances,

tools and motor loads.The generator’s revolving field is

driven at about 3,600 rpm by a single-cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload the

Generator” on page 10.

Every effort has been made to ensure that information in this

manual is accurate and current. However, Generac reserves

the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency. For

warranty information refer to the engine owner’s manual.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or serious

injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION

indicates a hazard which, if not avoided, might result in

minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

• Operate generator ONLY outdoors.

• Keep at least 2 feet of clearance on all sides of generator for

adequate ventilation.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground circuit fault interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

DANGER

• National Electric Code requires generator to be properly

grounded to an approved earth ground. Call an electrician for

local grounding requirements.

Failure to properly ground generator can result

in electrocution, especially if the generator is

equipped with a wheel kit.

DANGER

WHEN ADJUSTING OR MAKING REPAIRS TOYOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

Unintentional sparking can result in fire or

electric shock.

WARNING

7000EXL Extended Life Generator

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing gas cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel

to spill.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays around battery for a long

time after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

WARNING

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Your Generator” on page 10.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or

contact Generac.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

7000EXL Extended Life Generator

KNOWYOUR GENERATOR

Read this owner’s manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

12 Volt DC,10 Amp Receptacle — Recharge a discharged

12 Volt automotive type battery through this receptacle.

120 Volt AC, 20 Amp Duplex Receptacle — May be used to

supply electrical power for the operation of 120 Volt AC, 20 Amp,

single phase, 60 Hz electrical lighting, appliance, tool and motor

loads.

120 Volt AC, 30 Amp Locking Receptacle — May be used to

supply electrical power for the operation of 120 Volt AC, 30 Amp,

single phase, 60 Hz electrical lighting, appliance, tool and motor

loads.

120/240 Volt AC, 30 Amp Locking Receptacle — May be

used to supply electrical power for the operation of 120 and/or

240 Volt AC, 30 Amp, single phase, 60 Hz electrical lighting,

appliance, tool and motor loads.

Air Cleaner — Uses a dry type filter element and foam

pre–cleaner to limit the amount of dirt and dust sucked into the

engine.

Choke Lever — Used when starting a cold engine.

Circuit Breakers (AC) — The 120 Volt AC, 20 Amp duplex

receptacle is provided with "push to reset" circuit breakers to

protect the generator against electrical overload.

Double Pole Circuit Breaker (AC) — A double pole circuit

breaker is provided to protect all the receptacles and generator

against electrical overload.

Fuel Tank — Capacity of seven (7) U.S. gallons.

Grounding Wing Nut — Used for proper grounding of unit.

Idle Control Switch — With this switch set to ON, generator

automatically reduces engine speed when no load is connected

and increases engine to proper speed when load is applied.

However, be sure switch is OFF when starting engine.

Oil Fill Cap — Add oil to engine here.

Recoil starter — Used to start the engine manually.

Run/Stop Switch — Set this switch to "Run" before starting

engine. Set switch to "Stop" to switch OFF engine.

Spark Arrester Muffler — Exhaust muffler lowers engine noise

and is equipped with a spark arrester screen.

Start Button — When pressed, cranks engine to start.

120 Volt AC, 20 Amp

Duplex Receptacle

Fuel Tank

Idle Control

Switch

Choke Lever

Start Button

12 Volt DC, 10 Amp

Receptacle

Run/Stop Switch

120 Volt AC, 30 Amp

Receptacle

Circuit Breakers (AC)

120/240 Volt AC,

30 Amp Receptacle

Spark Arrester Muffler

Air Cleaner

Grounding

Wing Nut

Oil Fill Cap Recoil Starter

Double Pole

Circuit Breaker

7000EXL Extended Life Generator

ASSEMBLY

Check Battery / Attach Negative

Battery Wire

The sealed battery on the generator is fully charged and

pre–installed except for the negative (black) battery cable.

To install:

• Cut off tie wrap securing loose end of negative (black)

cable.

• Remove nut and washer on the negative battery

terminal.

• Slide the negative battery cable over the screw on the

negative terminal (Figure 1).

• Reattach washer and nut and tighten.

• Verify that the connections to the battery and generator

are correct and secure.

BEFORE STARTING THE

ENGINE

Add Oil

CAUTION! Any attempt to crank or start the engine

before it has been properly filled with the recommended

oil may result in an engine failure.

To fill your engine with oil:

• Place generator on a level surface.

• Follow the oil grade recommendations and oil fill

instructions given in the engine owner’s manual.

NOTE: The generator’s revolving field rides on a

prelubricated and sealed ball bearing that requires no

additional lubrication for the life of the bearing.

Add Fuel

WARNING! NEVER fill fuel tank indoors. NEVER

fill fuel tank when engine is running or hot.Allow

unit to cool for two minutes before refueling. DO

NOT light a cigarette or smoke when filling the fuel

tank.

WARNING! DO NOT overfill the fuel tank.

Always allow room for fuel expansion.

• Use regular UNLEADED fuel with the generator

engine. DO NOT use premium fuel. DO NOT mix oil

with fuel.

• Clean area around fuel fill cap, remove cap.

• Slowly add unleaded regular fuel to fuel tank. Be careful

not to overfill.Allow about 1/2" of tank space for fuel

expansion (Figure 2).

• Install fuel cap and wipe up any spilled fuel.

IMPORTANT: It is important to prevent gum deposits

from forming in essential fuel system parts, such as the

carburetor, fuel filter, fuel hose or tank during storage.Also,

experience indicates that alcohol–blended fuels (called

gasohol, ethanol or methanol) can attract moisture, which

leads to separation and formation of acids during storage.

Acidic fuel can damage the fuel system of an engine while

in storage. Be sure to review the precautions given in

“Storage” on page 12.

NEVER use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

Figure 1 — Negative Battery Connection

Positive battery cable

Screw

Washer

Nut

Negative

battery

cable

Figure 2 — Typical Fuel Expansion Space

1/2” Air

Space

Tank

Fuel

7000EXL Extended Life Generator

GROUNDING THE

GENERATOR

The National Electrical Code requires that the frame and

external electrically conductive parts of this generator be

properly connected to an approved earth ground. Local

electrical codes may also require proper grounding of the

unit. For that purpose, a GROUNDING WING NUT is

provided on the generator end (Figure 3).

Generally, connecting a No. 12 AWG (American Wire

Gauge) stranded copper wire to the grounding wing nut

and to an earth–driven copper or brass grounding rod

(electrode) provides adequate protection against electrical

shock. Be careful to keep the grounding wire attached after

connecting the stranded copper wire. However, local codes

may vary widely. Consult with a local electrician for

grounding requirements in your area.

Properly grounding the generator helps prevent electrical

shock if a ground fault condition exists in the generator or

in connected electrical devices, especially when the unit is

equipped with a wheel kit. Proper grounding also helps

dissipate static electricity, which often builds up in

ungrounded devices.

OPERATING THE

GENERATOR

CAUTION! NEVER start or stop unit with

electrical loads connected AND with the connected

devices turned ON.

IMPORTANT: Always unplug the battery float charger

before starting the generator.

Starting the Engine

Disconnect all electrical loads from the generator. Follow

these start instruction steps in numerical order:

1. Turn the fuel valve to the “On” position (Figure 4).

2. Make sure the Idle Control switch is in “Off” position

(Figure 5).

3. Set the Run/Stop switch to “Run” position (Figure 6).

4. Place the choke lever in the “Full” choke position

(Figure 7).

Figure 4 — Fuel Shut-offValve

Figure 5 — Idle Control Switch

Figure 6 — Run/Stop Switch

Figure 7 — Choke Positions

Figure 3 — Grounding Wing Nut

Grounding

Wing Nut

Fuel Valve shown in

the “On” position

7000EXL Extended Life Generator

5A. For electric starting, press start switch on

generator cradle.To prolong the life of the starter

components, press the starter button for no more

than 15 seconds, and pause for 30 seconds.

5B. For manual starting, grasp the recoil handle and pull

slowly until slight resistance is felt.Then pull rapidly

one time only to start engine.

• If engine starts, proceed to step 7.

• If engine fails to start, proceed to step 6.

6. Move the choke lever to “Half” choke position, and

press start button or pull recoil handle twice.

• If engine fails to start, repeat steps 4 thru 6.

7. Move choke lever to “Run” position. If engine falters,

move choke lever to “Half” choke position until the

engine runs smoothly and then to “Run” position.

NOTE: If engine still fails to start after 3 pulls, check for

proper oil level in crankcase.This unit is equipped with a

Low Oil Shutdown System. See engine manual.

Refer to the engine owner’s manual for complete

starting instructions.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120Volt

receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See

“Don’t Overload the Generator” on page 10.

Stopping the Engine

• Unplug all electrical loads from generator panel

receptacles. NEVER start or stop engine with electrical

devices plugged in and turned on.

• Put the idle control switch in the “Off” position.

• Let engine run at no–load for 30 seconds to stabilize the

internal temperatures of engine and generator.

• Move run/stop switch to “Stop”.

• Close the fuel shut–off valve.

Operating Automatic Idle Control

This switch is designed to greatly improve fuel economy.

When this switch is turned ON, the engine will only

run at its normal high governed engine speed when an

electrical load is connected.When an electrical load is

removed, the engine will run at a reduced speed. With

the switch off, the engine will run at the normal high

engine speed. Always have the switch off when

starting and stopping the engine.

Charging a Battery

WARNING! Storage batteries give off explosive

hydrogen gas while recharging.An explosive mixture

will remain around the battery for a long time after

it has been charged.The slightest spark can ignite

the hydrogen and cause an explosion, resulting in

blindness or other serious injury.

WARNING! DO NOT permit smoking, open

flame, sparks or any other source of heat around a

battery.Wear protective goggles, rubber apron and

rubber gloves when working around a battery.

Battery electrolyte fluid is an extremely caustic

sulfuric acid solution that can cause severe burns. If

spill occurs flush area with clear water immediately.

Your generator has the capability of recharging a

discharged 12 Volt automotive or utility style storage

battery. DO NOT use the unit to charge any 6Volt

batteries. DO NOT use the unit to crank an engine having

a discharged battery.

To recharge 12Volt batteries, proceed as follows:

• Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

• If the battery is equipped with vent caps, make sure they

are installed and are tight.

• If necessary, clean battery terminals.

• Connect battery charge cable connector plug to panel

receptacle identified by the words “12-VOLTS D.C.”.

• Connect battery charge cable clamp with red handle to

the positive (+) battery terminal (Figure 8).

7000EXL Extended Life Generator

• Connect battery charge cable clamp with black handle

to the negative (–) battery terminal (Figure 8).

• Start engine. Let the engine run while battery recharges.

• When battery has charged, shut down engine.

NOTE: Use an automotive hydrometer to test battery state

of charge and condition. Follow the hydrometer

manufacturer’s instructions carefully. Generally, a battery is

considered to be at 100% state of charge when specific gravity

of its fluid (as measured by hydrometer) is 1.260 or higher.

COLD WEATHER

OPERATION

Under certain weather conditions (temperatures below

40°F [4°C] and a high dew point), your generator may

experience icing of the carburetor and/or the crankcase

breather system.

Build a structure that will enclose three sides and the top

of the generator.

• Make sure entire muffler-side of generator is exposed.

Note that your generator may appear different from that

shown in Figure 9.

• Ensure a minimum of two feet clearance between open

side of box and nearest object.

• Face exposed end away from wind and elements.

• Enclosure should hold enough heat created by the

generator to prevent problems.

CAUTION!NEVER run unit indoors. DO NOT

enclose generator any more than shown. Remove

generator from shelter when temperature is above

40°F [4°C].

How to Use the Battery Charger

Use battery float charger jack to keep the starting battery

charged and ready for use. Battery charging should be done

in a dry location, such as inside a garage.

• Plug the charger into the unit’s “Battery Float Charger”

jack, which is located on the starter switch (Figure 10).

Plug battery charger into a 120 Volt AC wall receptacle.

• Unplug the charger from the unit and the wall outlet

when generator is being started and while it is in

operation.

• Keep this charger plugged in when generator is not in

use to prolong battery life.The charger has a built in

float equalizer and will not overcharge the battery, even

when plugged in for an extended period of time.

IMPORTANT: See “Battery Maintenance” on page 11 for

additional information.

RECEPTACLES

120 Volt AC, 20 Amp Duplex

Receptacle

Each of these outlets is protected against overload by

20 Amp push-to-reset type circuit breakers (Figure 11).

Figure 10 — Battery Charger Jack

Figure 9 — Permanent Cold Weather Shelter

Wind

Figure 8 — Battery Connections

7000EXL Extended Life Generator

Use each outlet to operate 120 Volt, 60 Hz, single phase

loads requiring 2,400 (2.4 kW) watts at 20 Amps of

current.

120/240 Volt AC, 30 Amp Locking

Receptacle

Use a NEMA L14-30 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volts at 30 Amps (or greater)

(Figure 12).You can use the same 4-wire cord if you plan to

run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts of power at

20 Amps for 120 Volts; 7,000 watts of power (7.0 kW) at

29.2 Amps for 240 Volts.The outlet is protected by a

double pole circuit breaker.

CAUTION! Although this outlet is rated for

240 Volt 30 Amp (up to 7.200 watts), the generator

is only rated for 7,000 watts. Powering loads that

exceed the wattage/amperage capacity of the

generator can damage it or cause serious injuries.

240 Volt loads powered through this outlet should

not exceed 29.2 Amps of current draw.

120 Volt AC, 30 Amp Locking

Receptacle

Use a NEMA L5-30 plug with this receptacle. Connect a

3-wire cord set rated for 125 Volts AC at 30 Amps to the

plug (Figure 13).

Use this receptacle to operate 120Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts (3.6 kW) of power

at 30 Amps.The outlet is protected by a double pole circuit

breaker.

12 Volt DC, 10 Amp Receptacle

This connector (identified by the legend “12-VOLT D.C.”)

supplies 12 Volts DC at 10 Amps through battery charging

cables for recharging 12 Volt batteries (Figure 14). See

“Charging a Battery” on page 7.

Figure 11 — 120Volt AC, 20 Amp Duplex Receptacle

Figure 13 — 120 Volt AC, 30 Amp, Locking Receptacle

3-Wire Cord Set

Neutral

120V

Hot

Ground (Green)

NEMA L5-30

Figure 14 — 12Volt DC, 10 Amp Receptacle

Figure 12 — 120/240 Volt AC, 30 Amp Receptacle

4-Wire Cord Set

240V

120V 120V W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30 Ground (Green)

7000EXL Extended Life Generator

DON'T OVERLOADYOUR

GENERATOR

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.This is

the amount of power your generator must produce to

keep your items running. See Figure 15.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator.There should be nothing connected to the

generator outlets before starting it's engine.The correct

and safe way to manage generator power is to sequentially

add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly.

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.Take

special care to consider surge loads in generator capacity,

as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance Rated (Running)

Watts Additional Surge

(Starting) Watts

Window Air

Conditioner 1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts 1800 Highest

Surge Watts

Tool or Appliance Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 -

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 Cu. Ft. 800 1600

Water Well Pump - 1/3 HP 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 HP 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 -

Coffee Maker 1500 -

Electric Stove - Single Element 1500 -

Hot Plate 2500 -

Family Room

DVD/CD Player 100 -

VCR 100 -

Stereo Receiver 450 -

Color Television - 27” 500 -

Personal Computer w/17” monitor 800 -

Other

Security System 180 -

AM/FM Clock Radio 300 -

Garage Door Opener - 1/2 HP 480 520

Electric Water Heater - 40 Gallon 4000 -

DIY/Job Site

Quartz Halogen Work Light 1000 -

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 HP 1000 1000

Circular Saw - 7 1/4” 1500 1500

Miter Saw - 10” 1800 1800

Table Planer - 6” 1800 1800

Table Saw/Radial Arm Saw - 10” 2000 2000

Air Compressor - 1-1/2 HP 2500 2500

Figure 15 - Wattage Reference Chart

Andere Handbücher für 7000exl

Inhaltsverzeichnis

Sprachen:

Andere Generac Power Systems Tragbarer Generator Handbücher

Generac Power Systems

Generac Power Systems 005734-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6500XL Bedienungsanleitung

Generac Power Systems

Generac Power Systems XP Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems MAGNUM MGG200 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Portable Generator Service-Handbuch

Generac Power Systems

Generac Power Systems NP-66LPG Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems 005626-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems GP1800 Bedienungsanleitung

Generac Power Systems

Generac Power Systems XP Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems iQ2000 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Protector Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems 005792-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems GP Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems 0065141C Bedienungsanleitung

Generac Power Systems

Generac Power Systems XT8000E Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems CENTURION 006104-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems EcoGen G0070340 Merkblatt

Generac Power Systems

Generac Power Systems GP Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems IX1600 Bedienungsanleitung

Generac Power Systems

Generac Power Systems RS5500 Bedienungsanleitung

Generac Power Systems

Generac Power Systems iQ3500 Bedienungsanleitung

Generac Power Systems

Generac Power Systems XP6500E XP SERIES Bedienungsanleitung

Generac Power Systems

Generac Power Systems 0830890SRV Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6500XL Bedienungsanleitung

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

evertz

evertz 7700 Series Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung

Wallenstein

Wallenstein GF5000A Bedienungsanleitung

Leroy-Somer

Leroy-Somer LSA 49.1 Bedienungsanleitung

Yamakoyo

Yamakoyo SH2900DX Bedienungsanleitung