Generac Power Systems XP Series Bedienungsanleitung

Australia 1 800 333 28. New Zealand 09 269 1160

Owner's Manual

50Hz XP Series Portable Generator



DEADLY EXHAUST FUMES! ONLY use OUTSIDE far away

from windows, doors and vents!

NOT INTENDED FOR USE IN CRITICAL LIFE SUPPORT

APPLICATIONS.



SAVE this Manual. Provide this manual to any operator of

the generator.

Introduction............................................................. 1

Read this Manual Thoroughly ................................. 1

Safety Rules ........................................................... 1

General Information................................................ 4

1.1 Unpacking......................................................................4

1.1.1 Accessory Box ..................................................4

1.2 Assembly.......................................................................4

1.2.1 Assembling the Wheel Kit ..................................4

1.2.2 Battery Connection ............................................4

Operation ................................................................ 5

2.1 Know the Generator .......................................................5

2.2 Hourmeter - With Reset..................................................7

2.3 Connection Plugs ...........................................................7

2.3.1 230 VAC, 15 Amp, AS/NZS 3112 Receptacle.....7

2.4 How to Use the Generator ..............................................8

2.4.1 System Ground..................................................8

2.4.2 Connecting to a Buildings Electrical System .......8

2.4.3 Connecting Electrical Loads ...............................8

2.5 Overload Prevention .......................................................9

2.6 Before Starting the Generator .........................................9

2.6.1 Adding Engine Oil ..............................................9

2.6.2 Adding Gasoline.................................................9

2.7 Starting the Engine (Electric Start Only)........................10

2.8 Starting Pull Start Engines............................................10

2.9 Stopping the Engine .....................................................11

2.10 Low Oil Level Shutdown System ..................................11

2.11 Charging the Battery (if equipped) ................................11

Maintenance ......................................................... 11

3.1 Performing Scheduled Maintenance .............................11

3.2 Maintenance Schedule .................................................11

3.3 Product Specifications..................................................12

3.3.1 Generator Specifications ..................................12

3.3.2 Engine Specifications.......................................12

3.4 General Recommendations...........................................12

3.4.1 Generator Maintenance ....................................12

3.4.2 To Clean the Generator.....................................12

3.4.3 Engine Maintenance.........................................12

3.4.4 Checking Oil Level ...........................................12

3.4.5 Changing the Oil and Oil Filter ..........................13

3.4.6 Replacing the Spark Plug .................................13

3.4.7 Battery Replacement........................................13

3.4.8 Air Filter Replacement......................................13

3.4.9 Clean Spark Arrestor Screen ............................14

3.4.10 Adjusting Valve Clearance................................14

3.5 General ........................................................................15

3.6 Long Term Storage.......................................................15

Troubleshooting .................................................... 16

4.1 Troubleshooting Guide..................................................16

Notes .................................................................... 17

Table of Contents

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Authorized Dealer for starting, operating and servicing

procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using

the equipment. We also strongly recommend instructing other

users to properly start and operate the unit. This prepares them

if they need to operate the equipment in an emergency. Save

these instructions for future reference. If you loan this device

to someone, ALWAYS loan these instructions to the individual

as well.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

• Become familiar with and strictly adhere to all local, state and

national codes and regulations.

• Study all safety warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.

This symbol points out potential explosion

hazard.

!This symbol points out potential fire hazard.

This symbol points out potential electrical

shock hazard.

Introduction

GENERAL HAZARDS

• NEVER operate in an enclosed area, in a vehicle, or indoors

EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends that the

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

• Operate generator only on level surfaces and where it will not be

exposed to excessive moisture, dirt, dust or corrosive vapors.

• Keep hands, feet, clothing, etc., away from fans and other

moving parts. Never remove any fan guard or shield while the

unit is operating.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

• Do NOT operate generator in the rain.

• Do not alter the construction of the generator or change

controls which might create an unsafe operating condition.

• Never start or stop the unit with electrical loads connected

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

• Do not insert objects through unit’s cooling slots.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Lifting Warning Hazard: A falling generator can result in death,

bodily injury, and/or property damage. Stand clear of generator.

Lift is designed to carry only the weight of the generator. DO

NOT overload lifting bracket. Apply lifting strap or hook through

lift bar hole(s) only. DO NOT lift while generator is running.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

• On electric start models, disconnect the POSITIVE (+) battery

cable from the engine starter OR the NEGATIVE (-) battery

cable from the battery terminal, whichever is easier, before

transporting the generator.

•

EXHAUST & LOCATION HAZARDS

• Never operate in an enclosed area or indoors! NEVER use in

the home, in a vehicle, or in partly enclosed areas such as

garages, EVEN IF doors and windows are open! ONLY use

outdoors and far from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide, which

you cannot see or smell. This poisonous gas, if breathed in

sufficient concentrations, can cause unconsciousness or even

death.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

• This exhaust system must be properly maintained. Do nothing

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

• Always use a battery operated carbon monoxide alarm indoors,

installed according to the manufacturer's instructions.

• If you start to feel sick, dizzy, or weak after the generator has

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

• Never handle any kind of electrical cord or device while

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

Safety Rules

• The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or highly

conductive area (such as metal decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged electrical

cord sets with the generator.

• Before performing any maintenance on the generator, disconnect

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

• Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.

NEVER permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

• Never add fuel while unit is running or hot. Allow engine to cool

completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws regulating

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

• Do not insert objects through unit’s cooling slots.

• NEVER operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

• Keep a fire extinguisher near the generator at all times.

• Do not operate in a hazardous location where there may be a

risk of explosion of petrol fumes, leaking fuel or explosive dusts.

MODEL NO:

SERIAL NO:

Unit ID Location

Safety Rules

1.1 UNPACKING

• Remove all packaging material.

• Remove separate accessory box.

• Remove carton off the generator.

1.1.1 ACCESSORY BOX

• 2–Wheels • OilFunnel

• 2–HairPins • 2–FrameFeet

• SparkPlug • 12VoltAdaptorPlugCharger

• AirFilter • SparkPlugWrench

• OilFilter • ShopTowel

• 2–Bolts • 2–FlatWashers(small)

• 2–5/8"FlatWashers(thin) • 2–5/8"FlatWashers(thick)

• 2 – 1 Quart SAE 30 Oil Bottles

1.2 ASSEMBLY

Read entire Owner's Manual before attempting to assemble or

operate the generator. The generator requires some assembly

prior to using it. If problems arise when assembling the generator,

please call an authorized dealer at 1 800 333 28 for Australia and

09 269 1160 for New Zealand.

1.2.1 ASSEMBLING THE WHEEL KIT

The wheel kit is designed to greatly improve the portability of the

generator. A 10mm wrench is needed to install the Frame Feet.

NOTE:

The wheel kit is not intended for over-the-road use.

Refer to Figure 1 and install the feet and wheels as follows:

1. Align the hole in the frame foot to the hole in the frame. Secure

foot with a bolt and flat washer (small). Repeat for other foot.

2. Slide the axle through the holes on the axle brackets.

3. Slide on one 5/8" flat washer (thick), the wheel and a 5/8" flat

washer (thin) onto the axle.

4. Secure with hair pin and repeat for the other wheel.

Figure 1 – Wheel Assembly

1.2.2 BATTERY CONNECTION

NOTE:

The battery shipped with the generator has been fully charged.

A battery may lose some of its charge when not in use for

prolonged periods of time. If the battery is unable to crank

the engine, plug in the 12V charger included in the accessory

box (see the Charging a Battery section). RUNNING THE

GENERATOR WILL CHARGE THE BATTERY.

The unit has been deliberately shipped with the battery cables

disconnected. You will need two 8mm wrenches to secure the

battery cables.

See Figure 2 for connection details.

1. Cut off cable ties securing the battery cables.

2. First, connect the red battery cable and the red battery charger

wire to the positive (+) battery terminal. Use the supplied

screw and lock nut.

3. Connect the black battery cable and the black battery charger

wire to the negative (-) battery terminal. Use the supplied

screw and lock nut.

4. Make sure all connections are secure. Slide the rubber boots

over the terminals and connection hardware.

Figure 2 - Battery Connections

General Information

2.1 KNOW THE GENERATOR

Read the Owner’s Manual and Safety Rules before operating

this generator.

Compare the generator to Figures 3 through 5 to become familiar

with the locations of various controls and adjustments. Save this

manual for future reference.

1. 230 Volt AC, 15 Amp, AS/NZS 3112 – Supplies electrical

power for the operation of 230 Volt AC, 15 Amp, single-phase,

50 Hz electrical lighting, appliance, tool and motor loads.

2. Circuit Breakers (AC) – Each receptacle is provided with a

push-to-reset circuit breaker to protect the generator against

electrical overload.

3. Fuse – This 1.5 Amp fuse protects the Battery Charger Input

jack.

4. Hourmeter – Tracks hours of operation and alerts to service

intervals.

5. Choke Knob – Used when starting a cold engine.

6. Start Switch - Use to start engine from the starter motor.

NOTE:

The switch must be in the “On” position when starting the

engine from the recoil starter.

7. Spark Plug - See the Maintenance Schedule and Engine

Specification sections for details.

8. Oil Filter - See the Maintenance Schedule and Engine

Specification sections for details.

9. Oil Drain – Use to drain engine oil.

10. Oil Fill – Add oil here.

11. Air Filter – Filters intake air as it is drawn into the engine.

12. Recoil Starter - Use to start engine manually.

13. Muffler – Quiets the engine.

14. Spark Arrestor – Reduces fire hazards by containing sparks.

15. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

16. Handles – Pivot and retract for storage. Press the spring-

loaded button to move handles.

17. Fuel Tank – See generator Specifications for tank capacity.

18. Gas Cap – Fuel fill location.

19. Fuel Gauge – Shows fuel level in tank.

20. Battery - Powers the electric starter motor.

21. Battery Charger Input - This receptacle allows the capability

to recharge the battery from the adaptor plug charger.

22. Lifting Device – use to lift and store the generator after use.

See Lifting Safety notes in the beginning of this manual.

23. Fuel Shut Off – Valve between fuel tank and carburetor.

Operation

Figure 3 - 5,600 Watt Control Panel

Operation

Figure 4 - 6,400 Watt Control Panel

19 22

18 17

410cc Engine for

5.6 & 6.4 kW Models

Figure 5 - Generator Controls

Operation

2.2 HOURMETER - WITH RESET

The Hourmeter tracks hours of operation for scheduled maintenance

(see chart) (Figure 6).

Operation: Push and release the reset button to toggle between

screens. The hours count backwards from the set interval as

shown in the chart.

When the meter reaches 5 hours,the text "CHG OIL" (or "SVC AIR

FILTER" or "CHG PLUG") will flash continually for two minutes.

After this time, the meter will go back to displaying the total hours

of the unit (for 2 minutes). This cycle will repeat for the entire 5

hours.

When the service interval reaches zero hours, the text "NOW"

replaces the hours remaining.

For a new generator for instance, the message will say "CHG OIL"

then flash "in 30". This means that in 30 hours, the oil will need to

be changed. Pressing the button a few more times will bring the

meter back to the screen that shows the total hours run.

Reset: Toggle to the alert that you wish to reset then hold the

button down for 9 seconds. The maintenance hours are reset when

the display shows "0000.0".

NOTE:

The hour glass graphic will flash on and off when the engine

is running. This signifies that the meter is tracking hours of

operation.

Figure 6 – Hourmeter

HOUR GLASS

GRAPHIC

RESET BUTTON

(IF EQUIPPED)

0000.0

2.3 CONNECTION PLUGS

2.3.1 230 VAC, 15 AMP, AS/NZS 3112 RECEPTACLE

This is a 230 Volt outlet protected against overload by a 15 Amp

push-to-reset circuit breaker (Figure 7). Use each socket to power

230 Volt AC, single phase, 50 Hz electrical loads requiring up to a

combined 3450 watts (3.4 kW) or 15 Amps of current. Use only

high quality, well-insulated, 3-wire grounded cord sets rated for

230 Volts at 15 Amps (or greater).

Keep extension cords as short as possible, preferably less than 5

meters long, to prevent voltage drop and possible overheating of

wires.

Figure 7 – 230 Volt AC, 15 Amp, AS/NZS 3112

Receptacle

Hourmeter (With Reset) Chart

Message Frequency of Message Interval Duration of message

CHG OIL Initial break-in period First 30 Hours

ON/OFF for 2 minutes in a 5

hour period

CHG OIL Re-occuring 100 hours

SVC AIR FILTER Re-occuring 200 hours

CHG PLUG Re-occuring 200 hours

2.4 HOW TO USE THE GENERATOR

To obtain contact information for the nearest authorized dealer,

contact AllPower Industries. For Australia 1 800 333 28, for New

Zealand 09 269 1160.



Never operate in an enclosed area or indoors! NEVER

use in the home, in a vehicle, or in partly enclosed

areas such as garages, EVEN IF doors and windows are

open! ONLY use outdoors and far from open windows,

doors, vents, and in an area that will not accumulate

deadly exhaust.



The engine exhaust fumes contain carbon monoxide,

which you cannot see or smell. This poisonous gas,

if breathed in sufficient concentrations, can cause

unconsciousness or even death.



Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation. Do not

alter the installation or permit even partial blockage of

ventilation provisions, as this can seriously affect safe

operation of the generator. The generator MUST be

operated outdoors.



This exhaust system must be properly maintained. Do

nothing that might render the exhaust system unsafe

or in noncompliance with any local codes and/or

standards.



The manufacturer recommends installing a battery

operated carbon monoxide alarm indoors, according to

the manufacturers instructions.

2.4.1 SYSTEM GROUND

The generator has a system ground that connects the generator

frame components to the ground terminals on the AC output

receptacles.

Special Requirements

There may be federal, state, safety or health administration

regulations, local codes, or ordinances that apply to the intended

use of the generator.

Please consult a qualified electrician, electrical inspector, or the

local agency having jurisdiction:

• In some areas, generators are required to be registered with

local utility companies.

• If the generator is used at a construction site, there may be

additional regulations which must be observed.

2.4.2 CONNECTING TO A BUILDING’S ELECTRICAL

SYSTEM

Connections for standby power to a building’s electrical system

must be made by a qualified electrician. The connection must

isolate the generator power from utility power or other alternative

power sources and must comply with all applicable laws and

electrical codes.

Grounding The Generator

Local electrical codes may require proper grounding of the unit

(Figure 8). For that purpose, connecting a 2.59mm stranded

copper wire to the grounding lug and to an earth-driven copper

or brass grounding rod (electrode) provides adequate protection

against electrical shock. However, local codes may vary widely.

Consult with a local electrician for grounding requirements in

the area.

2.4.3 CONNECTING ELECTRICAL LOADS

DO NOT connect 120 Volt loads to 230 Volt receptacles.

DO NOT connect 3 phase loads to the generator.

DO NOT connect 60 Hz loads to the generator.

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 230 Volt AC, single phase, 50

Hz electrical loads.

• Add up the rated watts (or amps) of all loads to be connected

at one time. This total should no be greater than (a) the rated

wattage/amperage capacity of the generator or (b) circuit

breaker rating of the receptacle supplying the power. See “Don’t

Overload the Generator.

Operation

Andere Handbücher für XP Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Generac Power Systems Tragbarer Generator Handbücher

Generac Power Systems

Generac Power Systems 004991-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Guardian 005240 Montageanleitung

Generac Power Systems

Generac Power Systems Mobile Power MMG405 Bedienungsanleitung

Generac Power Systems

Generac Power Systems WHEELHOUSE 1646-3 Bedienungsanleitung

Generac Power Systems

Generac Power Systems GP8000E Bedienungsanleitung

Generac Power Systems

Generac Power Systems MC10000 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 005788-0 XG4000 Bedienungsanleitung

Generac Power Systems

Generac Power Systems IX 800 Bedienungsanleitung

Generac Power Systems

Generac Power Systems XG Professional 005802-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems PowerBOSS 8000 PowerMaster Bedienungsanleitung

Generac Power Systems

Generac Power Systems 02010-0 PRIMEPACT 50 Betriebsanleitung

Generac Power Systems

Generac Power Systems 7000exl Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1576-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems GP Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems SVP5000 97193 Bedienungsanleitung

Generac Power Systems

Generac Power Systems MAGNUM MMG75D Bedienungsanleitung

Generac Power Systems

Generac Power Systems 004920-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems XP Series Bedienungsanleitung

Generac Power Systems

Generac Power Systems Mobile Power MMG25FHI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 005734-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems LP3250 LP SERIES Bedienungsanleitung

Generac Power Systems

Generac Power Systems WheelHouse 5500 Bedienungsanleitung

Generac Power Systems

Generac Power Systems QT05030AVAN Bedienungsanleitung

Generac Power Systems

Generac Power Systems 0065781 Bedienungsanleitung

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

ConMed

ConMed 7550 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

Power Stroke

Power Stroke PS906025 Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

PowerBoss

PowerBoss PowerBoss Bedienungsanleitung

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung