Generac Power Systems 1293-1 Bedienungsanleitung

2700PSI

This pressure

washer is

equipped with an

Automatic Cool

Down System.

See page 11 for

details

This symbol points out important safety instructions, which, if not followed, could

endanger the personal safety and/or property of yourself and others. ead and follow

all instructions in the manual before attempting to operate this unit.

Model No. 12931 (2700 PSI High Pressure Washer) Manual No. B3836 evision 0 (1/11/99)

Owner’s Manual

Problems?

Questions?

Before taking your unit

back to the store,

call the pressure washer

helpline at

1-800-270-1408

M-F 8-5 CST

GENERAC

The Reliable Ones

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

CAUTION! Always disconnect spark plug wire and place wire where it cannot contact spark plug to

prevent accidental starting when setting up, transporting, ad usting or making repairs to your high pressure

washer.

 Engine exhaust gases contain DEADLY carbon

monoxide gas. This dangerous gas, if breathed

in sufficient concentrations, can cause

unconsciousness or even death. Operate this

equipment only in the open air where adequate

ventilation is available.

 Gasoline is highly FLAMMABLE and its vapors

are EXPLOSIVE. Do not permit smoking, open

flames, sparks or heat in the vicinity while

handling gasoline. Avoid spilling gasoline on a hot

engine. Allow unit to cool for 2 minutes before

refueling. Comply with all laws regulating storage

and handling of gasoline.

 Use this pressure washer in areas away from

combustible materials, combustible fumes or

dust.

 The high pressure equipment is designed to be

used with Generac authorized parts only. If you

use this equipment with parts that do not comply

with minimum specifications, the user assumes

all risks and liabilities.

 Some chemicals or detergents may be harmful

if inhaled or ingested, causing severe nausea,

fainting or poisoning.

 Do not allow CHILDREN to operate the pressure

washer at any time.

 Operate engine only at governed speed. Running

the engine at excessive speeds increases the

hazard of personal in ury. Do not tamper with

parts which may increase or decrease the

governed speed.

 Do not wear loose clothing, ewelry or anything

that may be caught in the starter or other rotating

parts.

 Before starting the pressure washer in cold

weather, check all parts of the equipment and be

sure ice has not formed there.

 Units with broken or missing parts, or without

protective housing or covers should NEVER be

operated.

 The muffler and air cleaner must be installed and

in good condition before operating the pressure

washer. These components act as spark arrestors

if the engine backfires.

 Check the fuel system for leaks or signs of

deterioration such as chafed or spongy hose,

loose or missing clamps or damaged tank or cap.

Correct all defects before operating the pressure

washer.

 Do not spray flammable liquids.

 Never aim the gun at people, animals or plants.

 The high pressure stream of water that this

equipment produces can pierce skin and its

underlying tissues, leading to serious in ury.

 High pressure spray can cause paint chips or

other particles to become airborne and fly at high

speeds.

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects, or other reproductive harm.

WWAANNIINNGG::

Important!  Safety ules  Important!

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

 Always wear eye protection when you use this

equipment or when you are in the vicinity where

the equipment is in use.

 Never move the machine by pulling on the high

pressure hose. Use the handle provided on the

top of the unit.

 Always be certain the spray gun, nozzles and

accessories are correctly attached.

 Never use a spray gun which does not have a

trigger lock or trigger guard in place and in working

order.

 Use a respirator or mask whenever there is a

chance that vapors may be inhaled. Read all

instructions with the mask so you are certain it

will provide the necessary protection against

inhaling harmful vapors.

 High pressure spray may damage fragile items

including glass. Do not point spray gun at glass

when in the high pressure spray mode.

 Keep the hose connected to machine and the

spray gun while the system is pressurized.

Disconnecting the hose while the unit is

pressurized is dangerous.

 Hold the spray gun firmly in your hands before

you start the unit. Failure to do so could result in

an in ury from a whipping spray gun. Do not leave

the spray gun unattended while the machine is

running.

 The cleaning area should have adequate slopes

and drainage to reduce the possibility of a fall due

to slippery surfaces.

 Keep water spray away from electric wiring or fatal

electric shock may result.

 Do not secure trigger gun in the pull-back (open)

position.

 Do not by-pass any safety device on this machine.

 The muffler and engine heat up during operation

and remain hot immediately after shutting it down.

Avoid contact with a hot muffler or engine or you

could be severely burned.

 Operate and store this unit on a stable surface.

 Never allow any part of the body to come in

contact with the fluid stream. DO NOT come in

contact with a fluid stream created by a leak in

the high pressure hose.

 High pressure hose can develop leaks from wear,

kinking, abuse, etc. Water spraying from a leak

is capable of in ecting material into skin. Inspect

hose each time before using it. Check all hoses

for cuts, leaks, abrasions or bulging of cover, or

damage or movement of couplings. If any of

these conditions exist, replace hose immediately.

Never repair high pressure hose. Replace it with

another hose that meets minimum pressure rating

of your pressure washer.

Important!  Safety ules  Important!

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

CONG ATULATIONS on your purchase of a

GENERAC high pressure washer. It has been

designed, engineered and manufactured to give you

the best possible dependability and performance.

Should you experience any problem you cannot

easily remedy, please contact your nearest

GENERAC Authorized Service facility, or call the 1-

800 number listed on the front of this manual. We

have competent, well-trained technicians and the

proper tools to service or repair this unit.

Please read and retain this manual. The instructions

will enable you to assemble and maintain your high

pressure washer properly.

CUSTOME

ESPONSIBILITIES

 Read and observe the safety rules.

 Follow regular schedule in maintaining, caring for

and using your high pressure washer.

 Follow the instructions under Customer

Responsibilities and Storage sections of this

Owner's Manual.

P ODUCT

SPECIFICATIONS

Pressure Washer Specifications

Outlet Pressure . . . . 2700 psi

Flow ate . . . . . . . . . 2.7 gallons per minute (gpm)

Detergent Mix . . . . . . Use undiluted detergent

approved for pressure

washers

Water Supply . . . . . . Not to exceed 140°F

Temperature

Automatic Cool . . . . Will cycle when water

Down System reaches 140°-145°F

Engine specifications

Engine Model . . . . . . Generac Power Systems GN

220 Model EHC 040471

ated Horsepower . . 7.8

Displacement . . . . . . 220cc

Spark Plug

Type . . . . . . . . RC-12YC

Set Gap To: . . 0.030 inch (0.76mm)

Gasoline Capacity . . 4.2 U.S. quarts

Oil . . . . . . . . . . . . . . . SAE 30

In the State of California a spark arrestor is required

by law (Section 4442 of the California Public

Resources Code). Other states may have similar

laws. Federal laws apply on federal lands.

NOTE: The spark arrestor must be maintained in

effective working order by the owner/operator.

You can order a replacement spark arrestor through

your authorized Generac service facility. See Engine

Owners Manual for part number.

Model Number 12931

Serial Number

Date of Purchase

The model and serial numbers will be found on a

decal attached to the pressure washer. record both

serial number and date of purchase and keep in a

safe place for future reference.

KNOW YOU P ESSU E WASHE

ead this owners manual and safety rules before operating your high pressure washer.

Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various

controls and ad ustments. Save this manual for future reference.

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

Automatic Cool Down System  Cycles water

through pump when water reaches 140°-145°F. Warm

water will discharge from pump under base of unit.

This system prevents internal pump damage.

Chemical Valve Handle  The handle allows you to

select the high pressure spray or the chemical spray

(located on the wand).

Dual Element Air Cleaner  Uses a dry type filter

element and foam pre-cleaner to limit the amount of

dirt and dust that gets in the engine.

Dual Lance  Must be connected to the spray gun.

Gas Tank  Fill with regular unleaded gasoline.

Goggles  Always use the enclosed goggles or other

eye protection when running your pressure washer.

High Pressure Hose  Connect one end to water

pump and the other end to spray gun.

High Pressure Outlet  Connection for high pressure

hose.

Primer Bulb  Used for starting a cold engine.

Pump  Develops high pressure.

Spark Arrestor Muffler  Exhaust muffler lowers

engine noise and is equipped with a spark arrestor

screen, a USDA mandate for engine use in national

forests and parks.

Spray Gun  Controls the application of water and

chemical onto cleaning surface with trigger device.

Includes safety latch.

Water Inlet  Connection for garden hose.

Spray Gun

Chemical Valve Handle

High Pressure Hose

Goggles

Dual Element

Air Cleaner

Gas Tank

Water Inlet

Pump equipped with

Automatic Cool Down System

High Pressure Outlet

Spark Arrestor

Muffler

Primer Bulb

Dual Lance

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

Read entire owners manual before you attempt to

assemble or operate your new pressure washer.

Your new pressure washer has been assembled at

the factory with the exception of those parts left

unassembled for shipping purposes.

EMOVE P ESSU E

WASHE F OM CA TON

 Remove parts box included with pressure washer.

 Slice two corners at guide handle end of carton

from top to bottom so the panel can be folded down

flat, then remove all packing material.

 Roll pressure washer out of carton.

CA TON CONTENTS

Items in the carton include:

 Main Unit

 Manual Bag

 Owners Manual

 Engine Owners Manual

 Nozzle Cleaning Kit

 ORing Maintenance Kit

 StaBil® Brochure

 STABIL®

 Owner Registration Card

 Parts Box (which includes the following):

 Video

 Engine Oil

 Wireform

 Goggles

 Spray Gun

 Dual Lance

 High Pressure Hose

 Handle

 Handle Parts Bag (which includes the following):

 2 carriage bolts

 2 knobs

If any of the above parts are missing or damaged, call

the pressure washer helpline at 18002701408.

P EPA ING THE

P ESSU E WASHE

FO USE

If you have any problems with the assembly of your

pressure washer or if parts are missing or damaged,

call the Pressure Washer Helpline at 1-800-270-1408.

To prepare your pressure washer for operation you

will need to perform these tasks:

 Attach the handle and attach the wire form that

holds high pressure hose and spray gun.

 Connect high pressure hose to the spray gun and

the pump and connect water supply to the pump.

 Add oil to engine crankcase.

 Add fuel to fuel tank.

Attach the Handle

 Place the handle onto the bottom of the handle

supports already connected to the main unit. Make

sure the holes in the handle align with the holes in

the handle supports (Figure 1).

Note: It may be necessary to move the handle

supports from side to side in order to align the handle

so it will slide over the handle supports.

Figure 1  Attach the top of the handle to the

bottom of the handle.

Make sure

the holes in

the handle

supports

are aligned

with the

holes in the

handle.

Handle

Supports

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

 Insert the carriage bolts from the outside through

the holes on the handle and attach the plastic

knobs on the inside. Tighten the knobs by hand

(Figure 2).



Insert the wire support with the longer arm positioned

on the left. From this view (from rear of unit), the hook

resembles a J

(Figure 3)

Add Engine Oil

WA NING! Any attempt to crank or start the

engine before being properly serviced with the

recommended oil will result in an engine

failure.

Note: When adding oil to the engine crankcase, use

only high quality detergent oil rated with API service

classification SF,SG, SH or SH/CD rated SAE 30

weight. Select the oils viscosity grade according to

your expected operating temperature:

Do Not Use SAE 10W40 Oil.

Although multi-viscosity oils (5W30, 10W30, etc.)

improve starting in cold weather, these multi-viscosity

oils will result in increased oil consumption when used

above 32°F. Check your engine oil level more

frequently to avoid possible damage from running

low on oil.

To fill unit with oil:

 Place pressure washer on a level surface.

 Clean area around oil fill and remove oil fill cap

(Figure 4).

 Pour oil into the oil fill opening until it reaches point

of overflowing. DO NOT OVERFILL.

Note: The bottle of oil included with your pressure

washer contains more oil than the capacity of the

crankcase.

 Install oil fill cap, hand tighten securely.

Note: Check Oil Often During Engine Breakin.

Add Gasoline

DANGE ! Never fill fuel tank indoors. Never

fill fuel tank when engine is running or hot. Do

not smoke when filling fuel tank.

WA NING! Never fill fuel tank completely

full. Fill tank to about 1/2" below the bottom of

the filler neck to provide space for fuel

expansion. Wipe away any fuel spillage from

engine and equipment before starting.

The manufacturer recommends fresh, clean unleaded

automotive gasoline.

 Use clean fuel and store in approved containers.

Use clean fill funnels. Never use stale gasoline

left over from last season or gasoline stored for long

periods.

Figure 3  Fit wire form on handle.

Figure 4  Add oil to engine crankcase. Do not

attempt to start engine without

adding oil.

Figure 2  Insert the carriage bolts and attach

the knobs.

colder 32°F warmer

5W30 SAE 30

Oil Fill Cap

Make sure unit is on a level

surface before filling with oil!

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

ASSEMBLY

 Clean area around gas cap. Remove cap

(Figure 5).

 Add UNLEADED gasoline, slowly, to fuel tank.

Use a funnel to prevent spillage.

 Install gas cap and wipe up any spilled gasoline.

Connect Hose and Water

Supply to Pump

WA NING! You must assemble wand and

attach all hoses before you start engine.

Starting engine without all hoses connected

and water supplied will damage pump.

 Uncoil high pressure hose and attach the end of the

hose with the threaded end to the base of the spray

gun (Figure 6). Tighten by hand.

 Attach other end of high pressure hose to the high

pressure outlet on the pump (Figure 7). Tighten by

hand.

 Before you connect your garden hose to the water

inlet, inspect the water inlet screen (see Figure 8).

Clean the screen if it contains debris or have it

replaced if damaged. Do not run the pressure

washer if the water inlet screen is damaged.

 Connect garden hose to water inlet. Tighten firmly

by hand (Figure 8).

 Turn on the water (open valve completely).

 Squeeze trigger on gun to purge pump system of

air and impurities. Squeeze until a steady stream

appears.

WA NING! Before starting the pressure

washer, be sure you are wearing adequate eye

protection.

 Attach dual lance to spray gun. Tighten by hand.

Figure 6  Connect high pressure hose

to spray gun.

Figure 5  Add gasoline to fuel tank.

Gas Cap

Connect High Pressure

Hose Here

Figure 7  Connect high pressure hose to

pump.

Connect High

Pressure Hose

Here

Figure 8  Connect the garden hose to water

inlet and turn ON the water.

Check Screen

for Damage

and Connect

Garden Hose

Here

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

CHECKLIST BEFO E

STA TING ENGINE

If you have reached this point, look back over the

assembly to see if you have performed all of the

following.

 Check for properly tightened hose connections

(high pressure and water supply). Make sure the

hoses have no kinks, cuts, or damage.

 Check that oil has been added to proper level in

engine crankcase before trying to start the pressure

washer.

 Add proper gasoline to fuel tank.

 Provide proper water supply (not to exceed 140°F).

 Be sure to read Safety Rules and Operation

sections before using the pressure washer.

HOW TO USE YOU

P ESSU E WASHE

If you have any problems operating your pressure

washer, please call the pressure washer helpline at

1-800-270-1408.

How to Start Your Engine

The best way to start your engine-powered pressure

washer for the first time is to follow these instructions

step-by-step. This starting information also applies

whenever you start the engine after you have let the

pressure washer sit idle for at least a day.

 This pressure washer requires a water source that

flows at least 3.0 gallons per minute. Do not attempt

to siphon water from a non-pressurized container.

Place the pressure washer close enough to an

outside water source so that no more than 50' of

garden hose is needed.

 Check that the high pressure hose is tightly

connected to the spray gun and to the pump. See

ASSEMBLY section for illustrations.

 Connect the garden hose to water inlet on the

pressure washer pump and turn the water valve on

all the way.

WA NING! Do not run pump without the

water supply connected and turned on. You

must follow this caution or the pump will be

damaged.

 Remove dual lance from the spay gun.

 Squeeze trigger on spray gun until a steady

stream of water appears.

 Apply the safety latch to the spray gun trigger

(Figure 9).

 Place the Run/Stop switch to  un.

 Press the primer bulb 3 times, waiting 2 seconds

between each push

Note: For a warm engine, do not prime.

 Grasp rope handle and pull slowly until you feel

some resistance. Then pull cord rapidly to

overcome compression, prevent kickback and start

the engine. Let rope return to starter slowly.

If after 3 pulls the engine fails to start, disengage the

spray gun safety latch, squeeze the trigger to relieve

water pressure, re-engage the spray gun safety latch

and pull the recoil starter handle rapidly (Max. 3

pulls).

How to Stop Your Pressure Washer

 Move the Run/Stop switch to Stop.

 Simply shutting off the engine will not release

pressure in the system. Squeeze trigger on the

spray gun to relieve pressure in the hose.

Note: A small amount of water will spray out when

you release the pressure.

Figure 9  Safety Latch.

Safety Latch

Generac 2700PSI High Pressure Washer

GENERAC

The Reliable Ones

How to Use the Spray Gun and Dual

Lance

You now should know how to STA T your pressure

washer and how to STOP it. The information in this

section will tell you how to ad ust pressure and apply

chemicals using the spray gun and dual lance.

DANGE ! Never put hands in front of

nozzle.

 For most effective cleaning, keep spray nozzle

between 8 to 24 inches away from cleaning

surface.

 If you get spray nozzle too close, especially using

high pressure, you may damage the cleaning

surface.

 Do not get closer than 6 inches when cleaning

automobile tires.

Applying Detergent

IMPO TANT: Use soaps designed specifically for

pressure washers. Household detergents could

damage the pump.

To apply detergent follow these steps:

 Prepare the detergent solution as required by

chemical manufacturer. See chemical bottle for any

instructions

 Hang the detergent solution on J hook of the

wireform on the handle.

 Place small filter end of the chemical in ecting tube

into the detergent container (Figure 10).

CAUTION: Keep the plastic in ector tube

from coming in contact with the hot muffler.

This will damage the plastic tube. When

inserting the filter into a cleaning agent bottle,

route the tube so as to keep it from

inadvertently contacting the hot muffler.

 Open the chemical valve handle (Figure 11).

IMPO TANT: Detergent cannot be applied without

the water source turned on.

 Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to

spray gun and pump (see ASSEMBLY section

starting on page 6), and start engine.

 Apply detergent to a dry surface, starting from the

bottom and working up to avoid streaking.

 Allow the detergent to soak in for 3-5 minutes

before washing and rinsing. Reapply to prevent

surface from drying.

 For washing, start at lower portion of area to be

washed and work upward, using long, even,

overlapping strokes.

Figure 10  Insert the small filter into container

of cleaning solution.

Figure 11  Chemical valve handle.

Chemical Valve Handle

Andere Generac Power Systems Hochdruckreiniger Handbücher

Generac Power Systems

Generac Power Systems 1292-2 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1420-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1014-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2600 PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 3000CP Bedienungsanleitung

Generac Power Systems

Generac Power Systems OneWASH 6412 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6000CP Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6228-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1540-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 7132 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Power Washer Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1418-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1037-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1292-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems The Reliable Ones 1800PSI Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2100PSI 1536-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1417-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1455-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 10000025895 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1173-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 6020-2 Bedienungsanleitung

Generac Power Systems

Generac Power Systems BELT DRIVEN POWER WASHER Bedienungsanleitung

Generac Power Systems

Generac Power Systems 1067-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 2700PSI 1676-0 Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung

Hotsy

Hotsy 5645 Bedienungsanleitung