General TS06 Bedienungsanleitung

DIGITAL

MOISTURE METER

USER’S MANUAL

TS06

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

TABLE OF CONTENTS

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 –3

Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

What’s in the ackage . . . . . . . . . . . . . . . . . . . . . . . . . 3

roduct Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 4 –5

Setup Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . 6 –7

Checking Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operating, Maintenance & Safety Tips. . . . . . . . . 9 – 10

Warranty Information . . . . . . . . . . . . . . . . . . . . . 10 – 11

Return for Repair olicy . . . . . . . . . . . . . . . . . . . . . . . 11

FCC Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 – 12

Manual del Usuario . . . . . . . . . . . . . . . . . . . . . . . 13 - 28

INTRODUCTION

Thank you for purchasing General Tools & Instruments’

(General’s) TS06 Digital Moisture Meter. Please read this

user’s manual carefully and thoroughly before using the

instrument.

The TS06 can be used as a standalone moisture meter, or

with General’s free ToolSmart™app running on your mobile

phone. When used in concert with an iPhone®or Android™

smartphone, the meter can stream—via Bluetooth®— to the

phone all measurements it makes. The phone initiates the

data transfer using the ToolSmart™app, which can be

downloaded from the iTunes®App Store or Google Play Store.

The measurements can then be used to tag photos taken by

the phone’s camera. or example, the app can attach

moisture percentages to icons of different surfaces in a

rendering of a room as a way to compare their readiness for

finishing.

iPhone®and iTunes®are trademarks of Apple Inc., registered in the U.S. and other

countries.

Android™is a trademark of Google Inc.

The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by General Tools & Instruments is under license.

KEY FEATURES

• Incorporates separate moisture-resistance curves for

wood and building materials

• 99.9 count backlit high-contrast reverse-type (black on

white) LCD w/0.3 in. high digits

• Audible high moisture alert

• Squeezing trigger holds displayed readings

• Replaceable stainless steel test pins

• Pin cap doubles as calibration checker

• 3-minute Auto Power Off

• 1 year limited warranty

WHAT’S IN THE PACKAgE

The TS06 comes in a display box along with a “9V” battery and

an extra set of test pins.

PRODUCT OVERVIEW

ig. 1 above shows all controls, indicators and physical

components of the TS06. ig. 2 on the next page shows all

possible indications on the LCD.

A. Protective pin cap with calibrating resistor inside

B. Test pins with black rubber sleeves (sleeves not shown)

C. LCD

D. button. ress briefly to power meter on; press and

hold for >2 seconds to power meter off.

E. button. ress and hold to transmit moisture level

measurements to your smartphone via Bluetooth.

ress and hold again to silence transmission.

Fig. 1. The

controls,

indicators

and physical

structures

of the TS06

. MODE button. ress briefly to toggle between wood and

building materials measurement modes. ress and hold

to disable high moisture level alarm.

G. Measurement hold trigger. Squeeze to freeze displayed

reading. Squeeze again to release display.

H. Battery compartment

Fig. 2. All possible

indications on the

TS06 display

A. Low battery indicator

B. Moisture level reading

C. Wood measurement mode indicator

D. Indicates reading is being held

E. Building materials measurement mode indicator

. Bluetooth enabled indicator

SETUP INSTRUCTIONS

INSTALL BATTERY

Snap the battery compartment ( ig. 1, Callout H) open and

plug the included "9V" battery into the wired socket inside.

The terminals of the battery and the socket mate in only one

way, with the smaller male terminal plugging into the larger

female terminal. Close the compartment by snapping its

cover shut.

OPERATINg INSTRUCTIONS

To measure a moisture level:

1. Remove the protective pin cap.

2. Remove the black rubber protective sleeve from each test

pin.

3. Press the button to power the meter on. The meter will

sound one beep and the LCD will temporarily illuminate

with a backlight and the following readout: _ _ . _%

4. If you are measuring the moisture content of wood, skip

ahead to Step 5. To measure the moisture content of a

building material, briefly press the MODE button. This will

change the display to the following: __ __ . __%

5. Carefully press the test pins into the material whose

moisture level you wish to measure. The level will be

displayed as a percentage if it is within the measurement

range for the selected material:

For wood, the measurement range of the TS06 is 5 to

50%WME (Wood Moisture Equivalent). A moisture level

lower than 5% will produce the following readout: _ _ _%.

A level higher than 50% will produce a readout of _ _ _%

and sound the high moisture level audible alarm. The alarm

will sound for any wood moisture reading above 15.9%.

To silence the alarm, press and hold the MODE button.

For building materials, the measurement range of the

TS06 is 1.5 to 33%WME (Wood Moisture Equivalent). A

moisture level lower than 1.5% will produce the following

readout: _ _ _%. A level higher than 33% will produce a

readout of _ _ _% and sound the high moisture level

audible alarm. The alarm will sound for any building

WOOD

BLDG

material with a moisture reading above 19.9%. To silence the

alarm, press and hold the MODE button.

If silenced, the high moisture level alarm will automatically

be re-enabled after the TS06 is powered off and powered

on again. To re-enable the alarm without powering off the

meter, press and hold the MODE button.

To hold any reading (“freeze” the display), squeeze the

trigger ( ig. 1, Callout G). This will cause the word HOLD to

appear in the upper right corner of the LCD. To resume

measuring, squeeze the trigger again to make HOLD

disappear. This feature allows you to make a measurement in

a dark place or around a corner, hold the reading, and display

it within 3 minutes later where the lighting is better.

Measurements can be held for up to 3 minutes—the duration

of the meter’s Auto Power Off trigger.

To power off the meter, press the button and hold it for

more than 2 seconds.

To use the TS06 with your phone, begin by downloading

the ToolSmart™app from the iTunes Store or Google Play

Store and installing it. Then, pair the meter and your phone by

activating Bluetooth on your phone and pressing the

button ( ig. 1, Callout E) on the meter.

Pressing the button on the TS06 will cause the icon to

blink on the LCD for 30 seconds while the meter searches for

a device to pair with. If no Bluetooth device is detected within

30 seconds, Bluetooth transmission will cease and the

meter's internal Bluetooth circuitry will power down to save

battery power.

A tutorial on the app explains how to save moisture level

measurements to your phone and overlay them on photos of

your project taken by the phone’s camera.

CHECKINg CALIBRATION

You can verify the accuracy of the TS06’s readings by

manually checking its calibration at any time. To do so:

1. Remove the protective pin cap and note the small circuit

board attached to the inside of its rear wall. The rear wall also

has two small holes (left photo below) that provide access to

terminals on the circuit board. The circuit board contains a

resistor whose fixed value can be used to simulate a precise

moisture level and therefore check the calibration of the

meter.

2. Power on the meter, remove the black rubber protective

sleeves from the test pins, and push the pins into the

calibration holes (right photo below). If the meter is properly

calibrated, the displayed reading will be between 17.3%

and 19.3% in Wood Measurement mode. If you do not

obtain a reading within this range and your meter is still

under warranty, call General’s Customer Service

Department at 212-431-6100 to arrange to return the

meter for service or replacement.

SPECIFICATIONS

Measurement Range 5 to 50% for wood; 1.5 to 33% for

building materials

Measuring Accuracy ±2%

Test Pin Length 9mm (0.35 in.)

Operating Temperature -4º to 140º (-20º to 60ºC)

@ <85%RH

Current Consumption <50mA

Auto Power Off Trigger 3 minutes of inactivity

Backlight Characteristics 20 seconds at full brightness

after last button press; switches to

half-brightness after 20 seconds

Low Battery Icon Trigger <5.5V

Dimensions 7.01 x 2.76 x 1.65 in.

(178 x 70 x 42mm)

Weight (without battery) 4.1 oz. (115g)

Power Source “9V” battery (included)

OPERATINg, MAINTENANCE &

SAFETY TIPS

• Measurements of wood moisture level are skewed by two

variables: ambient humidity and the density of the wood

species. The best way to compensate for the effect of these

variables is to develop your own moisture level curves,

based on your experience working with different species of

wood on a day-to-day basis in your neighborhood.

or example, the humidity level affects the dryness of

interior wood considered “acceptable” for finishing. In the

steamy Deep South, where 60% relative humidity is the

norm, fine carpenters have learned how to work with wood

with 11% moisture content. But in bone-dry Nevada, Utah,

and Arizona, where 30% humidity is common, the same

piece of wood would have to have less than 6% moisture to

be considered “ready for finishing”.

• To locate the source of a leak behind wood, plaster, drywall

or a ceiling, make measurements at different locations. The

leak is where the meter displays the highest reading.

• Never use force to drive the test pins into a hard surface.

• Do not operate the TS06 in the presence of flammable or

explosive gases.

• Be careful not to stab yourself with the extremely sharp test

pins.

• Replace the protective pin cap and black rubber protection

sleeves after making measurements 1) for safety reasons

and 2) to avoid bending or dulling the pins.

• After subjecting the meter to a large change in ambient

temperature, wait at least 30 minutes before making

measurements to guarantee the accuracy of readings.

• Remove the battery when storing the unit or when you do

not expect to use it for an extended period of time (months

rather than weeks).

WARRANTY INFORMATION

In the U.S, General warrants its instruments and accessories,

and digital tools against defects in material or workmanship for

one year from the date of purchase unless otherwise stated on

the packaging, manual, and/or marketing materials. General

also warrants its non-digital tools products against defects in

material or workmanship on a limited lifetime term. The

company will replace or repair the defective unit, at its option,

subject to verification of the defect.

Inhaltsverzeichnis

Andere General Messgerät Handbücher

General

General MM70 Bedienungsanleitung

General

General EP8710 Bedienungsanleitung

General

General PM930SD Bedienungsanleitung

General

General DCFM8906 Bedienungsanleitung

General

General CM660 Bedienungsanleitung

General

General MM700D Bedienungsanleitung

General

General UV254SD Bedienungsanleitung

General

General DLM112SD Bedienungsanleitung

General

General DM8252 Bedienungsanleitung

General

General MMH800 Bedienungsanleitung

General

General DSM8925 Bedienungsanleitung

General

General MMD8P Bedienungsanleitung

General

General DAF4207SD Bedienungsanleitung

General

General DPH230SD Bedienungsanleitung

General

General LM30 Bedienungsanleitung

General

General EMF1394DL Bedienungsanleitung

General

General MMD4E Bedienungsanleitung

General

General MM7 Bedienungsanleitung

General

General VM8205SD Bedienungsanleitung

General

General SAF-T-LITE I.S. 300 Leitfaden

General

General EMHT40 Bedienungsanleitung

General

General WK2017SD Bedienungsanleitung

General

General MMD7NP Bedienungsanleitung

General

General DAMP60 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung