Gentec digiscan1 Bedienungsanleitung
-0-
-1-
Table of Contents
1. Precautions…………………………………………. 2
2. Preparation………………………………………….. 5
zStandard Accessories……………………….. 5
zParts Names………………………………….. 6
3. Install The Driver and Software…………………… 7
zInstall the Driver……………………………… 7
zInstall the Software………………………….. 8
4. Place Film/Slide into the Holder………………….. 9
5. Connecting the Digital Image Copier..…………… 10
6. Edit The Pictures/ Photo Editing Tools.................. 15
zAdjust…………….……………………………. 15
zRetouch…………..…..………………………. 19
zClipboard……………………………………… 21
9. Appendix…………………………………………….. 22
zSpecifications…………………………………. 22
zSystem Requirements……………………….. 22
10. Trouble Shooting……………………………………. 23
EN
-2-
Welcome
Thank you for purchasing a Digital Image Copier.
Please take a moment to read through this manual. Its
contents will send you on an educational journey into your
recorder multiple capabilities.
1. Precaution
Before using Digital Image Copier, please ensure that you
read and understand the safety precautions described
below. Always ensure that the image copier is operated
correctly.
•Never operate Digital Image Copier inside of an
aircraft or anywhere else where operation of such
devices is restricted. Improper use creates the risk
of serious accident.
•Do not try to open the case of Digital Image Copier
or attempt to modify Digital Image Copier in any way.
High-voltage internal components create the risk of
electric shock when exposed. Maintenance and
repairs should be performed only by authorized
service providers.
•Keep Digital Image Copier away from water and
other liquids. Do not use Digital Image Copier with
wet hands. Never use Digital Image Copier in the
rain or snow. Moisture creates the danger of fire and
electric shock.
•Keep Digital Image Copier and its accessories out of
the reach of children and animals to prevent
accidents or damage to the image copier.
-3-
•If you notice smoke or a strange odor coming from
Digital Image Copier, turn the power off immediately.
Take Digital Image Copier to the nearest authorized
service center for repair. Never attempt to repair
Digital Image Copier on your own.
•Use only the recommended power accessories. Use
of power sources not expressly recommended for
Digital Image Copier may lead to overheating,
distortion of the equipment, fire, electrical shock or
other hazards.
•Digital Image Copier may become slightly warm
during use. This does not indicate malfunction.
•If the exterior of Digital Image Copier needs cleaning,
wipe it with a soft, dry cloth.
EN
-4-
FCC Notice
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy. If not installed
and used in accordance with the instruction, it may cause
harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment on the off,
the user is encouraged to try to correct the interference by
one or more the following suggestion.
zReorient or relocate the receiving antenna.
zIncrease the distance between the equipment and
the receiver.
zConnect the equipment to a different power outlet
other than the one where the receiver is connected.
zConsult an experienced television or radio
technician for help.
CAUTION
To comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules, this device must
only be installed on computer equipment certified to
comply with the Class B limits.
-5-
Preparation
Standard Accessories
ImageCopier Manual CD
Positive Slide Holder Negative Film Holder
Clean brush
EN
-6-
Part Names
Note: We strongly suggest using a clean, dry, non-alcohol cotton
swab to insert into the image copier slot and clean the glass
surface periodically to produce a clear image. Please make sure
your film negatives/ mounted slides and cover trays are clean
before inserting into the copier as well. Dust or dirt from the
negatives and cover trays will affect the quality of your scanned
images.
-7-
3. Install the Driver and Software
To use the digital image copier you must install the Digital
Image Copier Driver and ArcSoft PhotoImpression 6 in
advance.
Installing the Driver
1. Turn on the computer.
2. Insert the installation CD into the CD-ROM drive and
the installation CD menu will appear.
3. When you see the following screen, Choose
“Scanner Driver”.
4. Follow the on-screen instructions to install driver.
Under XP OS
- Click “Next”
- Click “Install”
- Click “Finish”
EN
-8-
UnderVistaOS
- Click “Next”
- Click “Install”
- Click “Finish”
- Select “Locate and install driver software
(recommended)”
Installing the Software
1. Insert the installation CD into the CD-ROM drive and
the installation CD menu should appear.
2. When you see the following screen, choose “ArcSoft
Software Suite” to
install the software.
3. Follow the on-screen
instructions.
4. Setup MicroSoft
DirectX 9.0
5. The installed software
will automatically
create a
PhotoImpression 6
logo on your desktop.
6. Restart the computer.
-9-
4.PlaceFilm/SlideIntoTheHolder
1. Open the negative/ positive slide holder as Illustrated.
2. Put a negative film/ positive slide into holder as
shown.
3. Close the holder and please make sure the holder
close properly.
EN
Inhaltsverzeichnis
