Geo-FENNEL FL 250VA-N Bedienungsanleitung

Manual Utilizare

Users‘ manual

Nivele laser autonivelanta - orizontala si verticala

Fully Automatic Horizontal and Vertical Laser Level

FL 250VA-N

Kitul de Livrare

Laser rotativ FL 250VA-N, Receptor FR 45

cu clema pentru rigla de nivelare, telecomanda,

acumulatoru, incarcator, tinta magnetica,

ochelari laser, suport podea (integrat),

cutie transport, manual utilizare.

CARACTERISTICI

1) Fereastra emisie laser

2) Maner

3) Panou Control

4) 5/8“-conector pentru stativ

5) Priza pentru incarcator ( parte spate )

6) Capac compartiment baterii

7) Bula circulara

8) 2 suruburi reglaj pentru utilizare in pozitie

verticala

9) Picior fixare podea

KIT CONSISTS OF

Rotating Laser Level FL 250VA-N, receiver

FR 45 with clamp for levelling staff, remote

control, rechargeable batteries, charger,

magnetic target, laser glasses, floormount

(integrated), container, users‘ manual

FEATURES

1) Laser emitting window

2) Handle

3) Control panel

4) 5/8“ thread for tripod

5) Socket for charger (reverse side)

6) Battery compartment cover

7) Circular bubble

8) 2 foot screws for exact alignment at

use in vertical position

9) Floor fixing leg

DATE TEHNICE

Domeniu autonivelare ± 5°

Precizie

orizontal ± 1 mm / 10 m

vertical ± 1,5 mm / 10 m

Receptor FR45 ≥250m

Functie Punct

fara receptor ca. 50 m*

Scanare

fara receptor ca. 30 m*

Rotatie

fara receptor ca. 20 m*

Inclinare setare

axa X- si Y- ± 5°

Viteza de rotatie 200, 500 U / Min.

Timp de operare / 24h (NiMH)

Sursa de alimentare 48h (4 x C Alka-

line)

Temperatura operare -20°C - +50°C

Dioda laser/ Clasa laser 635 nm / 2

Protectie apa /praf IP 65

* depinde de lumina din camera

TECHNICAL DATA

Self-levelling range ± 5°

Accuracy

horizontal ± 1 mm / 10 m

vertical ± 1,5 mm / 10 m

WorkingrangewithFR45≥250m

Not rotating

w/o receiver approx. 50 m*

Scanning

w/o receiver approx. 30 m*

Rotating

w/o receiver approx. 20 m*

Gradual slope setting

in X- and Y-axis ± 5°

Rotating speed 200, 500 rpm

Operating time / 24h (NiMH)

Power supply 48h (4 x C alkal-

ine)

Temperature range -20°C - +50°C

Laser diode / Laser class 635 nm / 2

Dust / Water protection IP 65

* depending on room illumination

FUNCTII SI CARACTERISTICI FUNCTIONS AND FEATURES

FL 250VA-N fully automatic rotating laser is

a multi-functional laser instrument:

Horizontal and vertical fully automatic self-

levelling

Visible laser beam

Permanent 90° plumb beam

Variable scanning function –

both the scan range and scan direction can

be adjusted

Multistage rotating speed or laser point only

Setting slope up to 5° (X and Y-axis)

TILT-alarm function

FL 250VA-N complet automat de rotaþie cu

laser este un multi-funcþional cu laser :

Orizontalãþi verticalãcomplet automate

autonivelante laser Vizibil Permanent 90 °

fascicul fir cu Plumb Variabila Funcþia de

scanare - atât gama de scanare þi direcþia de

explorare se poate muta . mai multe trepte de

rotaþie a vitezei sau laser punct doar Setarea

pantãde pânãla 5 ° (X þi Y-axa) TILT-alarmã

funcþie

BATTERY AND CHARGER

Both the standard NiMH battery-pack and

4 x C alkaline batteries can be used.

NiMH battery pack

FL 250VA-N comes with NiMH rechargeable

battery pack. Connect the AC/DC converter

with socket “5”.

Permanent red light (at FL 250VA-N) indi-

cates that batteries are being charged.

Permanent green light (at FL 250VA-N) indi-

cates that batteries are fully charged.

Charging time is approx. 7 hours. The wor-

king time with fully charged battery pack is

approx. 24 hrs. * First time charging: If a

new battery pack will be charged the first

time we suggest to charge it for about

10 hours!

If power indicator lamp at control panel is

blinking the batteries have to be recharged.

4 x C Alkaline batteries

FL 250VA-N can be used with alkaline batte-

ries alternatively. The working time with new

alkaline batteries is approx. 48 hrs. Open

the battery compartment cover “6” by use of

a coin. Remove the plug and take out the

battery pack. Put in 4 x C Alkaline batteries

according to description inside of the battery

compartment (take care of correct polarity!)

Whilst use of alkaline batteries the recharging

function is disabled.

ACUMULATORII SI INCARCATORUL

Pot fi utilizate atat kit-ul de acumulatori NiMH

cat si baterii alcaline: 4x C

NiMH-pachet

Nivela FL 250VA-N vine cu pachet de acumulatori

reincarcabili NiMH. Conectati la incarcator prin

intermediul mufei (5)

Permanentãluminãroþie (de la FL 250VA-

N) indicãfaptul cãbateriile sunt în curs de

încãrcare. Lumina verde permanentã(de la

FL 250VA-N) indicãfaptul care bateriile

sunt complet încãrcate.

Durata de încãrcare este de aprox. 7 ore.

timpul de lucru cu bateria complet încãrcatã

este de aproximativ 24 de ore. * Prima

încãrcare: Dacão nouãbateria va fi

incarcata prima datãvãsugerãm são

incarcati pentru aproximativ 10 ore!

Dacãlampãindicatoare de putere de la

panoul de control clipeþte, bateriile trebuie

sãfie reincarcate.

4 x C baterii alcaline

FL 250VA-N poate fi utilizat cu baterii alcaline

alternativ. Timpul de lucru cu noi baterii

alcaline este de aprox. 48 de ore. Deschideþi

compartimentul capacul bateriei "6" prin

utilizarea unei monede. Scoateþi mufa si

scoateti acumulatorul. Puneþi înauntru 4 x

baterii alcaline C în conformitate cu

descrierea din interiorul compartimentului

bateriei (aveti grijãde polaritatea corectã!)

În timp ce utilizaþi baterii alcaline Funcþia de

reîncãrcare este dezactivatã.

PANOU CONTROL

1) Tasta Pornit/Oprit

2) Viteza de rotatie

3) Mod scanare

4) Mod inclinare

5) TILT-mod

6) Autonivelare

A- Indicatorul procedurii de calibrare

Nu este mentionat in manual, fiind doar pentru .

dealerii autorizati.

Comutare Pornit/Oprit unitate

Apasati “1” pentru pornire unitate FL 250VA-N

Apasati “1” din nou pentru inchidere unitate

CONTROL PANEL

1) ON/OFF button

2) Rotatin speed

3) Scanning mode

4) Slope mode

5) TILT mode

6) Self-levelling

A- Indicator lamps calibration procedure

Not mentioned in this manual. For autho-

rized dealers only.

SWITCHING UNIT ON/OFF

Press button “1” to switch the unit on.

Press button “1” again to switch the unit

off.

After switching on the unit flashing laser

diode indicates that automatic self-levelling

procedure is working. Self-levelling procedure

may take up to 30 seconds. Laser starts ro-

tating when self-levelled. If not the laser was

set up out of self-levelling range (indicating

lamp above button 5 is flashing). In this case

please set up instrument on more even sur-

face.

If power indicator lamp at control panel is

blinking during use of instrument the batte-

ries have to be recharged/alkaline batteries

exchanged.

Dupãpornire, pe unitate clipeþte dioda laser

indicand faptul cãse auto-niveleaza automat

Procedura este de lucru. Procedura de auto-

nivelare poate dura pânãla 30 de secunde.

Laserul începe sãse roteascãatunci când este

auto-nivelat. Dacãnu, laser a fost asezat

dincolo de gama de auto-nivelare (indicând

lampa deasupra butonului 5 intermitent). În

acest caz, va rugam sa înfiinþat instrumentul pe

o suprafaþãmai dreapta.

Dacãlampãindicatoare de putere de la panoul

de control clipeþte, în timpul utilizãrii

instrumentului, bateriile trebui sa fi reîncãrcate /

baterii alcaline schimbate.

ROTATING SPEED

FL 250VA-N standardly rotates with max.

speed. With button the speed can be

changed in 2 steps:

500 rpm -> 200 rpm -> 500 rpm.

VITEZA DE ROTATIE

MODUL SCANARE

Apasati tasta pentru schimbare

din rotatie in mod scanare.

Cu butonul

poate fi selectat unghiul de scanare

0° -> 15° -> 30°

MOD INCLINAT

Inclinarea se poate seta in

± 5° pe axa X si Y Apasati butonul

pentru intrare in mod SLOPE - inclinare ***.

Pentru schimbare intre axele X si Y, tastati

scurt

Lumina corespunzatoare axei aleasa

Pentru functia TILT pe axa aleasa apasati

Pentru inchidere mod SLOPE, apasati tasta.

lung circa 1 secunda si nivela se va autonivela.

SCANNING MODE

Press button to change from

rotating to scanning mode.

With button the scan range can be

changed in

3 steps: 0° -> 15° -> 30°

With buttons and the scan direction

can be changed counter-clockwise / clock-

wise. To quit scanning mode press button

„2”.

SLOPE MODE

Slopes can be set up to 5° in

X and Y direction. Press button

to enter the slope mode***

To change between X and Y-axis press but-

ton shortly.

Respective indication lamps show the axis

chosen.

To tilt the axis chosen press buttons

and .

To quit the slope mode press button

longer than 1 sec. and the FL 250VA-N will

start self-levelling procedure.

***In that moment the self-levelling mechanism is

disabled and the instrument enters the manual

mode. FL 250VA-N now can be tilted by use of a

grade mount.

FL 250VA-N mod standard se roteþte cu max.

vitezei. Cu butonul vitezei poate fi schimbat în

2 paþi: 500 rpm -> 200 rpm -> 500 rpm.

Cu butonul þi direcþia de utilizare

poate fi schimbatãcontra-sensul acelor de

ceasornic / sensul acelor de ceasornic. Pentru

a ieþi din scanare, apãsaþi butonul "2".

*** În acel moment, mecanismul de auto-nivelare

este dezactivata þi instrumentul intrãîn modul

manualul. FL 250VA-N acum poate fi înclinat prin

utilizarea unui suport inclinat.

FUNCTIA ALARM TILT

Pentru inchidere alarma TILT apasati tasta

din nou.

TILT ALARM FUNCTION

If level of FL 250VA-N is disturbed the instru-

ment will readjust itself (within the self-level-

ling range of 5°). If level is disturbed at large

range (for example if position of tripod leg

has changed by mistake) a height offset will

be caused. This will be avoided by the TILT-

function. The FL 250VA-N will shut off even

within the self-levelling range:

Switch unit on, wait until self-levelling proce-

dure is completed.

Press button TILT . If now the level is

disturbed the unit will not readjust itself but

stop rotating. Note: Not working in slope

mode. If required self-levelling procedure can

be started by pressing button in this

position.

To quit TILT-alarming function press button

TILT again.

UTILIZARE VERTICALA

VERTICAL USE

Unfold floor fixing leg and set instrument

with the floor mount to the floor.

FL 250VA-N is fully automatic self-levelling

in vertical direction, too. With the help of the

circular bubble the instrument can be set up

as accurately as possible.

Doing so you can use the maximum range

for slope setting.

•

Dacãnivela FL 250VA-N este deranjata,

instrumentul se va reajusta (domeniu de auto-

nivelare interval de 5 °). Dacãnivelul este

deranjat de mari miscari (de exemplu, în cazul

în care poziþia piciorului trepiedului s-a

schimbat din greþealã) o înãlþime de

compensare va fi cauzate. Acest lucru va fi

evitat de cãtre TILTfunction.FL 250VA-N se va

opri chiar þi în intervalul de auto-nivelare:

Porniti unitatea, aþteptaþi pânãcând este

auto-nivelata Procedura este finalizatã.

Apãsaþi butonului TILT. Dacãacum nivelul

este deranjat unitatea nu se va regla din nou,

ci se va opri rotirea. Nota: Nu lucreazãîn

modul pantã. Dacãeste necesara auto-

nivelarea, procedurãpoate fi pornitãprin

apãsarea buton pe aceastãpoziþie.

Asezati piciorului de fixare podea al

instrumentului cu podea de podea. FL 250VA-N

este complet automatãauto-nivelarea, în

direcþie verticalã, de asemenea. Cu ajutorul

bulei circularã, instrumentul poate fi configurat

cât mai precis posibil. Procedând astfel, aveþi

posibilitatea sãutilizaþi intervalul maxim pentru

setarea pantã.

TELECOMANDA

Tastele telecomenzii sunt identice cu cele

de la Nivela.

Distanta de lucru a telecomenzii - circa 50 m.

REMOTE CONTROL

The keys of the remote control are identical

to the keys of the instrument.

Switch FL 250VA-N on as described. Now

the unit can be operated with the remote

control.

To switch off FL 250VA-N press button “1”

on the instrument. Pressing this button on

the remote control will not switch off the

laser level completely (stand-by).

Toate functiile sunt identice ca la utilizarea

Orizontala. Exceptand:

All functions are identical to use in horizontal

position. Except:

Tilt function (slope) is possible in Y-axis only

in order to avoid mistakes!

After slope had been set unit will not start

self-levelling procedure after unit has swit-

ched off and on again.

Set up FL 250VA-N in horizontal position first

to carry out self-levelling procedure.

•

Funcþia Tilt (panta) este posibilãîn Y-axa numai

în scopul de a evita greþelile! Dupãce panta a

fost stabilitã, unitatea nu va porni Procedura de

auto-nivelare dupãinchiderea unitãþii a trecut

porniti din nou. Asezai nivela FL 250VA-N în

poziþie orizontalãsi prima data lasati sã

efectueze procedura de auto-nivelarea, .

Porniti FL 250VA-N aþa cum este descris.

Acumunitatea poate fi operat cu

telecomanda de control.

Pentru a opri FL 250VA-N apãsaþi butonul "1"

pe instrument. Apasand acest buton

petelecomanda nu se va opri nivel laser

complet (stand-by).

RECEPTOR FR 45 cu clema RECEIVER FR 45 with clamp

CARACTERISTICI

1) bule (2)

2) Display

3) Marcaj referinta

4) Fereastra receptie

5) Comutator Pornit/Oprit

6) Difuzor

7) Compartiment baterie (paret spate)

8) Sunet Pornit/Oprit

9) Precizie fina/normala/grosiera

10) Lumina inchis/deschis

11) Magneti(2)

12) 1/4“-conector montare clema-brida (parte spate)

FEATURES

1) Vial (2)

2) Display

3) Reference rabbet

4) Receiving window

5) ON / OFF switch

6) Loudspeaker

7) Battery compartment (back side)

8) Sound on / off

9) Accuracy fine / normal / coarse

10) Light on / off

11) Magnets (2)

12) 1/4“-mounting hole for clamp (back side)

KIT LIVRARE

Receptor FR 45, Baterie, clema prindere pe ,

rigla de nivelare, manual de utilizare

SUPPLIED WITH

Receiver FR 45, battery, clamp, users‘

manual

DATE TEHNICE

Indicatie Display fata

Precizie fina± 2 mm

Precizie normala± 4 mm

Precizie grosiera ± 10 mm

Tonalitate 3

Timp operare 400h

Sursa alimentare 1 x 9V

TECHNICAL DATA

Indication Front display

Accuracy fine ± 2 mm

Accuracy normal ± 4 mm

Accuracy coarse ± 10 mm

Tones 3

Operating time 400h

Power supply 1 x 9V

SIMBOLURI

1) Indicator pornire

2) Status baterie descarcata

3) Indicator detectie

4) Indicator sunet

5) Pozitie laser detectata

SYMBOLS

1) Power indicator

2) Low battery indicator

3) Detection indicator

4) Sound indicator

5) Detected position indicator

Precizie fina / normala / grosiera

Receptorul FR 45 are 3 trepte de sensibilitate

a precizii. Pentru selectare, apasati tasta (9)

Precizie grosiera

± 10 mm

Simbol display fara simbol

Precizie normala ± 4 mm

Simbol display

Precizie fina ± 2 mm

Simbol display

Accuracy fine / normal / coarse

The FR 45 is equipped with three precision

modes. It can be chosen by pressing button

(9):

Accuracy coarse ± 10 mm

Symbol on display: without symbol

Accuracy normal ± 4 mm

Symbol on display:

Accuracy fine ± 2 mm

Symbol on display:

INSTALAREA BATERIILOR

INSTALLATION OF BATTERIES

Open battery compartment cover (7).

Put in 1 x 9 V AA battery according to instal-

lation symbol (take care of correct polarity!).

Close cover.

In order to save battery power the receiver

will automatically turn off if it has not recei-

ved laser scanning singal for 5 minutes.

•

Deschideþi compartimentul pentru baterii (7).

Puneþi 1 x 9 V baterie AA în funcþie de simbolul

de instalare (aveti grijãde polaritate corecta!).

Închideþi capacul. În scopul de a economisi

energia bateriei receptorului se va opri automat

în cazul în care nu a primit raza laser scanare

semnal laser timp de 5 minute.

Andere Handbücher für FL 250VA-N

Inhaltsverzeichnis

Andere geo-FENNEL Laser-Nivelliergerät Handbücher

geo-FENNEL

geo-FENNEL FL 30 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO Geo6-XR GREEN SP Bedienungsanleitung

geo-FENNEL

geo-FENNEL MULTI-LINER FL 55 PLUS HP Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 69 HP Bedienungsanleitung

geo-FENNEL

geo-FENNEL Ecoline EL 167 Bedienungsanleitung

geo-FENNEL

geo-FENNEL MULTI-LINER FL 55 Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 100HAJunior Bedienungsanleitung

geo-FENNEL

geo-FENNEL Geo4-XR GREEN Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 110HA Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 245HV + Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 30 Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 60 Maxi Liner Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 100HA Junior Bedienungsanleitung

geo-FENNEL

geo-FENNEL CrossPointer5 SP Bedienungsanleitung

geo-FENNEL

geo-FENNEL FKL 50 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Torpedo Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 100 HA Bedienungsanleitung

geo-FENNEL

geo-FENNEL Geo5X-L360 HP Bedienungsanleitung

geo-FENNEL

geo-FENNEL Geo3X HP Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 220HV Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 70-GREEN SP Bedienungsanleitung

geo-FENNEL

geo-FENNEL DuoCrossPointer3 HP Bedienungsanleitung

geo-FENNEL

geo-FENNEL FET 220K-L Bedienungsanleitung

geo-FENNEL

geo-FENNEL FL 40-Pocket II Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung

Fixturlaser

Fixturlaser NXA D I-0912 Bedienungsanleitung

Wacker Neuson

Wacker Neuson PAL450 Bedienungsanleitung

geo-FENNEL FL 250VA-N Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken