GeoMax Zipp02 Bedienungsanleitung
GeoMax Zipp02
User Manual
Version 1.1
Zipp02 | 2Introduction
Introduction
Purchase Congratulations on the purchase of a Zipp02 instrument.
This manual contains important safety directions as well as instructions for
setting up the product and operating it. Refer to "7 Safety Directions" for
further information.
Read carefully through the User Manual before you switch on the product.
Product identifi-
cation The type and serial number of your product are indicated on the type plate.
Enter the type and serial number in your manual and always refer to this infor-
mation when you need to contact your agency or GeoMax authorised service
workshop.
Type: ______________________________________________
Serial No.: ______________________________________________
Introduction Zipp02 | 3
Symbols The symbols used in this manual have the following meanings:
Type Description
Danger Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Warning Indicates a potentially hazardous situation or an unintended
use which, if not avoided, could result in death or serious
injury.
Caution Indicates a potentially hazardous situation or an unintended
use which, if not avoided, may result in minor or moderate
injury and/or appreciable material, financial and environ-
mental damage.
Important paragraphs which must be adhered to in practice
as they enable the product to be used in a technically correct
and efficient manner.
Zipp02 | 4Table of Contents
Table of Contents
In this manual Chapter Page
1 Description of the System 7
1.1 Instrument Case 7
1.2 Instrument Components 8
2UserInterface 10
2.1 Function of Buttons 10
2.2 Display 13
3 Preparation before Measurement 14
3.1 Preparation of Battery 14
3.2 Erection of the Instrument 16
3.3 Leveling up of the Instrument 16
3.4 Centering 17
3.5 Collimation 18
3.6 Initial Settings 19
Table of Contents Zipp02 | 5
4 Operation Method 23
4.1 Start Up 23
4.2 Measurement of Angle 24
4.3 Turning Off the Instrument 28
4.4 Measuring Distance Using the Stadia Method 29
4.5 Installation and Removal of the Base 30
5 Inspection and Adjustment 31
5.1 Tubular Vial 31
5.2 Circle Vial 32
5.3 Laser Plummet 32
5.4 Perpendicular of Vertical Hair of Reticle of Telescope 34
5.5 Collimation Error 35
5.6 Index Error of Vertical Circle 36
6 Care and Transport 38
6.1 Transport 38
6.2 Storage 39
6.3 Cleaning and Drying 40
Zipp02 | 6Table of Contents
7SafetyDirections 42
7.1 General 42
7.2 Intended Use 42
7.3 Limits of Use 43
7.4 Responsibilities 44
7.5 Hazards of Use 45
7.6 Laser Classification 52
7.6.1 General 52
7.6.2 Laser Plummet 53
7.7 Electromagnetic Compatibility EMC 55
8TechnicalData 58
8.1 Technical Data of the Instrument 58
8.2 Conformity to National Regulations 60
9 International Limited Warranty 61
10 Accessories 62
11 Error Information 63
Description of the System Zipp02 | 7
1 Description of the System
1.1 Instrument Case
Instrument case Before placing the instrument into
the instrument case, align the dot
mark of the instrument upward
and on the same line, and lightly
tighten the clamp knobs and loos-
ened after the instrument is
placed in the case. All the clamp
knobs must be slightly tightened
again after the instrument is in
place in the case.
Zipp02 | 8Description of the System
1.2 Instrument Components
Instrument
components part
1 of 2
1. Screw of handle
2. Objective lens
3. LCD display I
4. Horizontal drive
5. Levelling screw
6. Handle
7. Laser plummet
8. Tribrach locking lever
6
7
8
5
4
3
2
1
Description of the System Zipp02 | 9
Instrument
components part
2 of 2
1. Focusing knob
2. Eyepiece
3. Optical sight
4. LCD display II
5. Circular vial
6. Battery case
7. Vertical drive
8. Tubular vial
2
1
3
4
5
6
7
8
Zipp02 | 10User Interface
2UserInterface
2.1 Function of Buttons
Description
Buttons
1. R/L button
2. HOLD button
3. V% button
4. 0SET button
5. ON/OFF button
6. Light button
1
3
5
2
4
6
Button Function 1 Other
ON/OFF Switch the instru-
ment On/Off 1. One of the function buttons for entering
into initial setting of the instrument.
2. One of the function buttons for entering
into index error setting.
3. One of the function buttons for entering
into compensation setting.
Inhaltsverzeichnis
Andere GeoMax Messgerät Handbücher
GeoMax
GeoMax Zoom 20 Pro Series Bedienungsanleitung
GeoMax
GeoMax Zoom40 Series Bedienungsanleitung
GeoMax
GeoMax Zenith60 Series Bedienungsanleitung
GeoMax
GeoMax Zenius5 Series Bedienungsanleitung
GeoMax
GeoMax Zeta125 Bedienungsanleitung
GeoMax
GeoMax Zoom80 Series Bedienungsanleitung
GeoMax
GeoMax ZIPP10 pro series Bedienungsanleitung
GeoMax
GeoMax Zoom90 Bedienungsanleitung
GeoMax
GeoMax Zoom20 Pro Series Bedienungsanleitung
GeoMax
GeoMax Zoom80 Series Bedienungsanleitung
GeoMax
GeoMax Zoom90 Bedienungsanleitung
GeoMax
GeoMax Zoom70 Bedienungsanleitung
GeoMax
GeoMax Zoom 75 Series Bedienungsanleitung
GeoMax
GeoMax Zipp20 series Bedienungsanleitung
GeoMax
GeoMax Zoom20 Pro Series Bedienungsanleitung
GeoMax
GeoMax Zone20 HV Bedienungsanleitung
GeoMax
GeoMax Zoom75 Bedienungsanleitung
GeoMax
GeoMax Zeta125 Bedienungsanleitung
GeoMax
GeoMax Zoom70 Bedienungsanleitung
GeoMax
GeoMax Zone60 DG Bedienungsanleitung
